Discussion Locked

PS/2 Mouse on HP Vectra VL 400 desktop

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have many of users using HP Vectra VL400 Series Pentium III desktops running Windows NT 4 workstation SP5. They are quite good slim line desktops.
The only problem is this annoying little mouse problem.
Where when a user saves their work or click's OK on a message box or whenever the HDD or CPU start doing it's actions. The mouse jumps all over the screen and sometimes disappear and is uncontrollable. It takes almost a minute before I get control over the mouse (PS/2 Wheel Mouse HP). It looks like it is taking up CPU time.

This is only happening on the VL400 Series.
I have tried the following to try and resolve the problem;
- use the latest mouse drivers
- use generic mouse driver
- used a serial mouse
- installed IDE NT 4 driver for this model
- installed latest video driver
- created a new image from scratch
- increased mouse buffer from 64 to 800

Also when i check the event viewer on the System log.
I mostly get the following event ID 37 on Source: i8042prt
" bogus RESET was detected on the mouse device"

Have checked this error in Microsoft Technet and cannot find any solution or an answer to this problem.
It looks like the mouse buffer overflows maybe because it is not clearing it's buffer correctly.
Can anyone help or give me a reason why this may be happening. I have already called HP Support and they don't know anything about this problem.

10 replies

by thechas

Have you scanned for viruses?

Unexplainable erratic behavior is always a clue to check for viruses.

Make sure your virus definitions are up to date.

by shanghai sam

I am using McAfee Virus Scan NT 4.5
with the latest virus definitions. And is always running in the background on these workstation.
If there was I virus the system scan should detect it.
I haven't tried a full virus scan on the systems though. But I will give it a try.

by timthetoolman

I'm with TheChas on that one. I cant find any references on the net at all re: "bogus RESET was detected on the mouse device"

The use of the word "bogus" has me wondering too. Its not a term Microsoft would use, I wouldn't think.

Do a virus scan if you haven't already.

Cheers,
Tim.

by timthetoolman

Hi,

OK, assuming you dont find any viruses...

Is this problem on one or many of the HP Vectra VL400 Series machines - is it on all of them?

I presume you've tried a new mouse (you said you tried a serial one...

Check to see if the IRQ for the mouse is being shared by another device. It should be IRQ 12 and there shouldn't be anything else using IRQ 12.

...if there is then see if you can relocate that device elsewhere.

Are you running anything unusual on the machines? Does the problem always happen? Does it happen from a safe start?

Cheers,
Tim.

by mistaherrera

Have fully scanned with the latest scan engine and virus definitions - did not find any virus.
Basically its almost all of them I would say about 90% of the same models PCs have the same problem. They all have the same configurations and image loaded onto them. Most of them that get the unexplainable mouse problem produces an error/warning on the system event log - ie. bogus reset was detected on mouse device. and referring to device i8042prt which is the intel ps/2 controller or mouse and keyboard port.
And yes I've already tried a new mice. Have also checked the IRQ and all is okay nothing is sharing IRQ 12 - only one using this is the mouse device - i8042prt.

There is nothing unusual runnning on those machines - other machines are okay. Problem does not always happen.
For example if the problem occurs on a workstation -
I would then try re-install the Intel Ultra ATA IDE driver.
Once that is done. The problem would disappear and won't re-appear for weeks or even a a few months.
I've also tried increasing the mouse buffer level through the registry.
Noticed that the problem re-appears more frequent - 1 week apart. - have increased buffer level higher everytime i visit the workstation every week - did not help.
Then today I have tried re-installing the mouseware pro - logitech driver.
currently monitoring - when the problem would re-appear.

Note: have tried increasing the mouse buffer as through checking in the syste event viewer it indicated the that there was a mouse buffer overflow.

by shanghai sam

Hi,

OK, I think that the mouse buffer isn't the problem. You said that the mouse jumps all over the screen and disappears? I'd say that the PC simply cant service all the interupts generated by the mouse at that time. Increasing the buffer size will only put off the inevitable overflow...

In fact to check that, the moment the mouse stops or "jumps" on the screen, stop moving the mouse. Eventually whatever is happening will finish up, you'll be able to move the mouse again, and I expect you would not get the overflow problem or bogus reset in the log.

So what is it causing the hang?

You said that re-installing the IDE drivers causes the problem to go away for a while. This is strange as the implication is that they get corruptedalong the way...but not so badly as to stop working. And furthermore, pretty much all of the machines do it...

I'd say there are a few more things to look at. The BIOS. Is it the most recent version? Can you update it?

Also get the latest video drivers. They're notorious for causing hang type problems.

Also, is it possible to upgrade one of the problem machines to SP6a? A bit of a longshot but it may help...

And... I suggest enabling performance monitoring with logging on a box withthe problem and on a box without the problem.

Do exactly the same things on the two boxes and compare the couters for each afterward. You will almost certainly see the applications behaving differently and this may give you some clue as to whats happenning.

At this stage, I'd be reasonably confident its a conflict in the device drivers, but between what and what, I dont yet know. The "obvious" guess is mouse drivers and IDE but that not necesarily going to be it.

Good luck,
Tim.

by shanghai sam

The second paragraph stated above is exactly what happens.

Anyway - I have already tried the latest BIOS and it is still happening on the PC and have already tried the latest video drivers. - The problem disappears for a few weeks and may comeback again.
Thanks for the suggestion anyway.

With SP6a - mmmmmmmm - I may try it on one of the VL400's.
I may also try performance monitoring on two pcs one with and one without the problem...if i can find a VL400 without the problem - or that has never had the problem.

Note: The problem mostly occurs in Lotus notes - whenever they receive an email or click's OK on a propmt box in Lotus notes.
And also happenning in Excel and Word. but can also happen whenever there is activity in the system which will require you to click OK or Cancel. -- this may not much info - but thought i'd let you know.

thanks again for attempting to resolve this mysterious mouse/system problem.

by orosas

Are you running any type of screen saver?. You might want to check your power settings and make it to be on all the time. So then the computer wont go to sleep.

by mistaherrera

orosas@ascosintering.com ,
yes - users are running a standard screen saver for the company. - but i don't see why this could affect the mouse behaviour same with the power settings - all ok.

To TimTheToolMan,
Have tried installing SP6a on one desktop pc (HP Vectrac VL400)which has the mouse problem and it still seems to happen.
Have notice for the past few weeks that users with the modified registry (increased mousedata queue)are able to temporarily fix the mouse behaviour by just reboot the PC.
PC's without the increased mousedata queue are unable to do this.
Still trying to figure this problem though.
This problem does not happen on Win2K Pro only on NT4.0.
Cannot upgrade these user's to this Win2K Pro due to the critical business applications they are running on the desktops.

This discussion is closed to new replies.