Discussion Locked

registry setting for NIC MAC address

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Where in the Win 9x registry is stored the MAC address of a NIC card?
I do believe is stored in HEX, but WHERE?
Any links to and/or info would be HIGHLY appreciated.

Thanks,
Florin

20 replies

by bowieb

I don't know about the registry, but you can find the MAC address of your NIC card from the winipcfg program. Go to Start|Run and type "winipcfg". You can see all of your network adapters, MAC addresses, IP addresses, etc.

by florinpetrescu

I am REALLY trying to find the registry key that holds information about NIC MAC address. It is a fixed (static) ip, so DHCP entries doesn't help me.

by parbo

Sorry to disappoint you but it is not stored in the registry. this information is gathered everytime from the card itself or out of cache.

by florinpetrescu

Sorry, but it's not there. There is no DHCP entry under hklm\sys\ccs\serv\vxd. It's a static ip machine: configured as static from the very beginning. And there is no entry under ...\vxd\mstcp for Mac address. Any other ideas?

by ann777

HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\VxD\DHCP\DHCPInfo00

or 01... 02 etc.

by ann777

And if it's not in DHCP then look under the MSTCP settings under the VxD set.

by florinpetrescu

Sorry, but it's not there. There is no DHCP entry under hklm\sys\ccs\serv\vxd. It's a static ip machine: configured as static from the very beginning. And there is no entry under ...\vxd\mstcp for Mac address. Any other ideas?

by florinpetrescu

Sorry, but it's not there. There is no DHCP entry under hklm\sys\ccs\serv\vxd. It's a static ip machine: configured as static from the very beginning. And there is no entry under ...\vxd\mstcp for Mac address. Any other ideas?

by computechie

The MAC address of a NIC isn't a registry entry, it's hard coded into a NIC card, at the time of manufacture. It's a FCC given code, and the first few digits identify the manufacturer of the card. Every NIC from every manufacturer has a different MAC address, and the same one will never be used again.

by jparade

I know this doesn't help you much Florinpetrescu, but Troy D is wrong. I've had problems on networks where the MAC addresses on 2 NICs were the same. I believ there is a key in the regisrty that allows you to change the MAC address. I'm not sure of it at this time, but I'll find out and get back to you with it. JAKE

by william jay

MAC address is a function of the NIC. Some NICs allow one to change the MAC by software config. To see what is the MAC address, type "nbtstat -a 192.168.114.4", but replace the ip address with your own!, or nbtstat will work the same given the machinename rather than the ip address. Now that you have the MAC, search the registry for it! To do that effectively, open regedit, save the registry to a text file, and use a text editor to open it and search ...

An IP address is a function of TCP-IP. Even if you use only netbeui or ipx, the MAC is the same. DHCP and other services may allow or deny based on a given MAC, but they don't use it for much else except identifying the location. Win2K allows several different concurrent ip/netmask assignments for each NIC, but there is only one MAC per card.

If your NIC is one that has a configurable or blank MAC, then run the dos-based utility that comes with it to set it to whatever you need it to be.

Please do not comment or reply to this post as it is correct and everything useful that can be said about this has already been said.

by akdude

I found that on a WinNT 4.0 box you can change the reported MAC. Don't remember how, but I think I found the whitepaper in TechNet. It doesn't change it on the NIC, just when nbtstat is used.

This discussion is closed to new replies.