38 replies
by derekdcosta
Try running msconfig (from Run) and then select the startup tab. deselect everything except essential windows apps.On the general tab choose not to load Environment variables.
Re-start and try scandisk again. I have also found that Norton Anti-Virus can cause the problem. If this works try to identify the cause of the problem by selectively activating the startup items 3 or 4 at a time. You may have to boot to safe mode to reactivate some of the System Config Utility settings.
by derekdcosta
Actually, the whole answer is here...
http://support.microsoft.com/default.aspx?scid=kb;EN-US;q222469
If this link doesn't work search support.microsoft.com for "q222469"
by diskaus
by diskaus
by thechas
You can boot from a startup floppy, and run scandisk from there.
This will clear up any "gross" errors that may be getting in the way.
In addition to the other suggestions, are the systems running low on virtual memory?
Scandisk and Defrag restart when anything causes a HDD access.
Make sure that screen savers are disabled, and consider disabling virtual memory.
by diskaus
by schultzd
I have seen this problem before. In my case I had an HP pinter file that was causing the problem. Removal of the offending file ended the problem right away. Check with HP support about this problem so they can identify the offending program for you.
Hope this helps.
by diskaus
by ann777
You have booted into Safe mode and scandisk/defrag will not complete? I have only seen this one time before...
Scandisk did complete; but defrag kept circling until the error message: "Scandisk has restarted 10 times" kept coming back.
Safe mode boots without anything but the basic neccesities of Windows... so I had this computer backed up, reformatted and re-imaged. I figured that the defrag utility got corrupted; scan disk was not showing any errors.
In your case, scandisk may be corrupted too. You can try to extract those programs from the cabinet files on cd, or you can start over. Formatting the drive and reinstalling seems to have resolved the problem for the computer that I saw.
by ann777
Sorry, one more thing to try in the case of Win98 computers.... boot to DOS prompt and do a manual scandisk without any options. When it finishes, andswer "yes" to "surface scan". Hopefully that does not show and bad sectors. If it's okay, thenreformat and reinstall. If it does show bad areas, then the hdd is probably going bad and should be replaced.
by diskaus
by rnegrete
hi, i hope i can help you. i work for Fic of taiwan.
i repair motherboards (compaq).
you can use a program to make a copy of your hard disk.
i use ghost.exe and d2d.exe
by diskaus
by bertievn
Close all your programs that load at start up and you will be able to scan without programs
Easy way to press control alt delete and clich on one by one except explorer and end task
Also works when writing cd or copy
by diskaus
by b_pope
by diskaus
by armour
by diskaus
by derekdcosta
Is the "...restarted..." message appearing even if you answer "no" to being notified again??
If you are networked, try disconnecting the cable ( and any other external devices)first. Possibly re-boot as well.
Running scandisk from a win 98/Me startup disk booted to the c:\ prompt ( no CD ROM support) would appear to be the only way around the problem. With only the command prompt running and both config.sys and autoexec.bat disabled this must surely work.
Have you tried running an updated virus scan... scanning ALL files, first?
by diskaus
When you get that error message and you click don't notify you again. Does it continue on or quit.
Second, are you connected to any kind of network or cable modem if so disconnect from that since sometimes it does make a connection to the hard drive also disable the screen saver during the scandisk and defrag.
by diskaus
by otl
Had same problem 36+hours later scandisk had not finished. This had nothing to do with what was running on the computer at the time (Explorer and Scandisk only, even tried safe mode)
This was with a HP system and 60G HDD (2 different ones!), after repartitioning drive to 3 - 20G parts, scandisk and defrag run beautifully. I know this is not an answer you would like to hear reload the OS after changing the partitions.
by diskaus
I have a 4 Gig Main drive and a 3 Gig storage drive
both 75%+ free space
by casta
by diskaus
by robert
by diskaus
by lizzy
by lizzy
by lizzy
by diskaus
by quaint_data
by diskaus
by diskaus
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending