Discussion Locked

Scanner HP 5p

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I would appreciate some help for solving the throubles I have with HP Scanjet 5p.
With Windows 98 SE I have had it working so and so only for limited time.. Actually it does not work and I am experiencing two strange facts.

1-If I tray to reinstall scanning software either the original old HP software either the new HP software, when the installation starts, after normal preliminars, I get the following advice:

Serious error
Unknown compression error: -1

when I click OK it reappears and so on for many times, finally I get the advice:

Serious
An error is happened, installation not succesfull. Close all applications and try again (Error 32).

When I click OK it goes back to desktop.

2-If I try to uninstall SCSI card, it is a Symbios Logic 53C416-NB, either if I have previously disabled it in Device Manager other not, when the PC restarts all goes well until the desktop appears, then the
PC freezes. The only thing I can do is shoot down the PC, reinsert SCSI card, reboot and the PC can work.

I do not tink that what I am experiencing depends from HP software, may be it depends from something wrong in my Windows 98 configuration.
The question is that I am not able to find it.
Obviously I have looked in
Control Panel | System | Device Manager |
and I have not found problems.

May be that in some points I was not very clear because I am translating from italian language and my knowledge of english language
is not very good..

Thanks for your help.

Andrea Doria

15 replies

by bucko77

I would guess that the compression error you are experiencing is from the setup files. Try downloading them again from www.hp.com

Make sure too that you close down any programs that are running like MS Shortcut bar and disable your virus scanner.

You need to REMOVE the SCSI card from Device manager not just disable it before you physical take the card out.

Good luck!

by dmiles

The error message could be caused by not enough memory and updating the drivers
Click on Start>Settings>Printers,click on the file menu and select properties check to see how much memory the printer has.
As for the SCSI card,remove the card from device manager and then let windows detect the card,you will want to look on the manufacturers site for updated drivers or other driver download sites to get latest drivers which you can find at www.driverforum.com or www.windrivers.com

by adoria1

What has printer to do with SCSI card for scanner? May be you refer to driver for SCSI card. It is no more supported from HP neither from Symbios Logic. I have 256 MB ram and also a mem defrag software.

by bucko77

Have you checked your BIOS? - I have seen some Compaq BIOSes that need you to remove the card from the BIOS as well as the OS

Good luck

by adoria1

I have checked the BIOS and I have not found any entry related to the card. When I installed the card I dont had to set something in the BIOS. Now my first trouble is that I am not able to keep away the card without PC freezing.
Thanks

by s_joe

Try to remove any hard drives or other componets attached to the scsi in the device manager before you remove the scsi tag. if windows boots with misleading hard drive and printer pointers, it may lockup.

hope this helps

by adoria1

No other component are attached to the SCSI, so I don't Know how following your suggestion.

Many thanks

Andrea

by buckle

Have you tried (in this order)
1. removing all the hardware
2. un-installing all the software
3. reboot
4. reinstalling the software
and when step 4 prompts you to reboot
5. reinstall the hardware and power on.

I always have problems with the HP scanners if I install the hardware before the software.

by abubin

it could be your system itself is giving problems. It could be faulty system or if you overclock, then that might be the reason. Try checking your RAM and motherboard if possible. It seems like your PC is transfering corrupted data. If all else fails, your windows could be corrupted itself. You should try formatting and re-install windows.

by dark force

Try this,
Boot to Safe Mode(press F8 when "Starting Windows 98" appears, or after POST is done), Remove all the SCSI Devices in Device Manager and all the scanner information(drivers/programs), shut down/power off.

Remove the SCSI Card, reboot. This should allow Windows to boot normally(and not freeze).
If Windows starts, shut down again and reinstall the card. When Windows boots, it should detect the SCSI card, let it finish.

When it finishes rebooting again, install the scanner software.

If this doesn't work, boot to DOS, rename the Windows Directory and reinstall it into a new directory.

Good Luck

This discussion is closed to new replies.