Question Locked

Slave drive access is denied after master drive re-installation - XP

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My master (C:) drive recently crashed and I have to reformat and reinstall the XP OS. Now, my slave drive (a separate hard disk) is not accessible: "Access is denied".

My 20 GB slave drive is using the NTFS file system and there are about 6 GB of data that I cannot afford to lose.

Is there any way I can recover the data or, better yet, make the slave drive accessible?

Thanks.

15 replies

by techexec2

This is normal and you should be able to restore access. You need to have the new system "take ownership" of the files on your slave drive. This article explains how to do this:

How to take ownership of a file or folder in Windows XP
http://support.microsoft.com/default.aspx?scid=kb;en-us;308421

-----

Note: If you used NTFS encryption, this will also apply:

Methods for Recovering Encrypted Data Files
http://support.microsoft.com/default.aspx?scid=kb;en-us;Q255742

-----

Tip of the hat to "HAL 9000".

by aknon

Hi! TechExec2,
I have managed to solve the slave drive access problem with the info taken from the link you have supplied.

Thank you very much.

by d.leduc

I have almost the same problem. If it was the same problem I'd already have my answer.

I have a computer running W2K with two IDE hard drives setup as master and slave. The slave drive is dynamic with only one volume. The master drive went bad and was replaced and reimaged from a generic system image. The slave drive now appears is system hardware and in disk management as dynamic and foreign. I've seen all kinds of articles that suggest that I should rescan then right-click and import foreign. Unfortunately that is not a choice on any menu that I've been able to find. I can only revert to basic, or look at properties and that doesn't help. Is there some command-line way that I can import foreign or is there some other way to get this disk visible to the rest of Windows 2000?

by multiplexed

I'm not sure, but an easier way might be to go to computer management\disk management and right click the slave drive. Then select import foreign disk.

by techexec2

I have never used "Import Foreign Disk". But, I think it applies to dynamic disks only (1).

REFERENCES

(1) Troubleshooting
http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/sag_disktrouble.mspx?mfr=true

(2) Disk status descriptions
http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/dm_status_disk.mspx?mfr=true

(3) To move disks to another computer
[i]"If the disks are dynamic disks, Disk Management displays Import Foreign Disks dialog box. Right-click any disk marked Foreign, click Import Foreign Disks, and then follow the instructions on your screen."[/i]
http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/dm_status_disk.mspx?mfr=true

by aknon

Hi! Multiplexed,

I have tried the method you suggested, but I could not find the feature to "import foreign disk".

But I was able to resolve the problem by reading up on the link provided by TechExec2.

Thanks anyway for your assistance.

by btyler02

I have a very similar problem. I reinstalled XP on my master drive which is SATA, but after the install when i connected my IDE drive, the BIOS and windows see the drive, but it has no assigned letter or way to access the contents on it. I have tried to use the Disk Manager, but it will not let me assign the drive a letter and when I tried the safe mode thing, it wouldn't let me go to the properties their either. The only options it gives me are to Reformat the drive or disconnect it? I can't afford to loose this info, and the whole reason I backed up everything was to avoid this situation? Any help is greatly appreciated!

by techexec2

Your problem is that the volume is not being mounted. This is entirely different that aknon's problem where the volume was mounted but access was rejected because the new system needed to take ownership of the files.

First of all, there is no "master" and "slave" with SATA. All drives are "master", one drive per cable.

Secondly, you refer to the PATA drive as "slave". If it is the only drive on the PATA IDE cable, it should be jumpered as "master". Or, it can be jumpered as "CS" (cable select) and be at the END of the cable, if the cable is an 80-wire IDE cable.

Third, is the SATA drive new to the system? Did you previously boot from the PATA drive?

I am suspicious that something bad might have happened to the PATA drive, or the data on it, while you were manipulating things. If Disk Manager can see the PATA drive, but does not show a partition on it (no NTFS or FAT partition), there may be something wrong with the drive.

by btyler02

I installed the SATA drive for the clean wipe and installed XP on it. Then after a boot into the new install I shutdown and plugged in the IDE drive with all my backup data on it. I unplugged it so I wouldnt possibly be able to loose the info? So much for that. So after the next boot windows recognized the drive and all, but it won't mount. I can see it in the Disk Management program, but the only option I have is to delete the partition. It shows the drive as Disk 0, 128.00 as NTFS Helthy(Active), then another partition of the unused space as 21.05 GB Unallocated. I am dumbfounded. I have tried mounting it as my external, no luck, tried it on my other computer, no luck? What gives?

by cougarjewel

My situation is an exact duplicate of this. Any answers?

by 5staar

If anyone can help!!! Please respond.

by pjotaduy

I had the same problem but with my C: drive, with the operating system in it. Wasted an enormous amount of time, mine and HP's support. Could not even Restore or reinstall the OS in the disk. The disk could be written on.
Minutes ago, after a week of trying, googling around I found the following, rather simple, fix:

http://support.microsoft.com/kb/810881/en-us

It fixed the whole disk from the root!
(I had to install the OS in a new disk first. The old C: did show in the My Computer screen but it could not be accessed and listed zero size and content in its properties! The fix above opened it all up. Am I glad!!!)
Take care,
Pedro

by sgt_shultz

that you have now discovered why the local admin account needs to be secured. because if you have local admin rights and physical access to the computer you can take ownership of anything on there...

This discussion is closed to new replies.