Discussion Locked

Store.exe = 100% CPU processor

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Problem=Store.exe = 100% CPU Utilization
Hardware = Compaq Proliant ML 370
640 RAM - 500mhz - C & D part 4G & 30G
NT4.0 SP4
Exchange 5.5 SP2

Steps to correct problem
1. Reboot several times
2. Install Post SP2 store for Exchange
3. install SP3 for Exchange
4. Install SP4 and Post-SP4-Store
5. Checked tech net for articles
a. Q243581 - Registry setting changed
b. Q172813 - Post SP4 Store (again)
c. Q272570 - Ran all utilities on the pub.edb and priv.edb. Cleaned out several problems and database is not showing any errors or inconsistancies
d. Ran a thorough virus check - cleaned out several e-mail messages with virus
e. Had all users clean out and delete unneeded messages, and transfer others to personal folders
f. Checked other technet articles and they did not apply or were done in the previous steps.
g. Have 2 or 3 threads eating up the process but cannot pin down which ones.

Besides a Re-Install, what else can be done? I really donot want to re-install if there are other options.

10 replies

by duwaned

It looks like you have pretty much covered most angles on the Exchange side of things, but what about NT?

Why not try to take NT server up to SP 6a. SP 4 was very unstable (I speak from experience!). There were problems with RPC connections in earlier versions of the NT service packs, and Exchange uses PRC to communicate with clients, and this could be causing your problem.

If you can't load a new SP on your server, then there is an RPC hotfix available at the following address:

ftp://ftp.microsoft.com/bussys/winnt/winnt-public/fixes/usa/NT40/hotfixes-postSP2/rpc-fix/rpc40i.exe

Let me know if this helps you out.
Regards.
Duwane

by larcat

I had the same problem. Look in the directory \exchsrvr\imcdata\out directory. I had about fifteen instances of Store.exe running when I looked into NT Monitor and when I looked into this directory there was fifteen email trying to send out. I removed the messages and problem was solved. These are text files and you can read them with Notepad. It may help to pinpoint the problem. It appears that they were looping. If you look at Event Viewer you should see an error that a file is in a loop. Letme also tell you that someone hacked into port 25 and set up a mail-relay to do this. I kept receiving emails in the postmaster account that I could not figure out where they were coming from. Take a look.

Larry

by rabbit_runner

I checked. There are no event viewer messages and that folder was empty, except for messages being sent at that moment. Thanks for the info.

by mtnsqs

1. Install later NT service pack - SP4 was unstable - SP 5 is very good.

2. For an exchange server you have very little RAM on the machine - Exchange is a high memory user - try to increase the system RAM and aslo check out the size of swap files.

by rabbit_runner

Just to add some additional info.
Pagefile = 4GIG (4000 meg)
I plan on installing NT SP6a during the weekend. I will report back later.

by rabbit_runner

I Tried to install service packs.
1. = SP4 40 bit
2. = SP4 128 bit
3. = SP5 40 bit
5. = SP6 128 bit
I tried each one in turn and the installed appeared normal. However, at the very end, when the percentage reached 100%, A message was displayed, 'The data is invalid' and I had to replace the system back to the original state. I am not certain what is happening at this point. Any Ideas would be helpful. Please let me know. Thanks

by duwaned

You might need to uninstall SP 4 first. It was so unstable that it needs to be removed before upgrading to a later version of Service pack.

Hav a look at MS TechNet article number:Q196603 for for info about removing SP 4. To find this article, goto www.microsoft.com, and do a search for the article number given above.

Regards.
Duwane

This discussion is closed to new replies.