Question Locked

System Crashes & Reboots when copying files to External USB hard drive

0 helpful
68 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

When I try to copy files to my usb hard drive my system freezes then reboots. Ive tried two different drives with different enclosures and the same thing happens with both of them. I have tried connecting them to different usb ports with no luck.
Does anyone have any idea what could be causing this or how to correct it?
I also have the same problem when accessing flash memory through my card reader.
Im running an AMD 4800+ Dual under windows xp pro with sp2.
I have an external enclosure with a maxtor 300 gig hard drive and an acomdata photon 2.5" 100 gig portable drive. Im using an ECS KN1 Extreme motherboard with a 600watt power supply and USB 2.0. My card reader is an I-Rocks and I also have a card reader in my epson rx500 usb printer. The external enclosure has its own power supply but the photon drive is bus powered.
Thanks in advance for you help

68 replies

by the scummy one

for updating in the questions forum. And also for replying back to the questions previously (I just read your other post).

A few suggestions to try:

First, uninstall the USB HDD and remove it.
Second -- Re-Install the chipset drivers for your MB
Third -- reboot, go into the BIOS and check for any USB settings. I have found less problems when enabling legacy USB support.
Fouth -- reboot, plug in the drive, let Windows detect the drive first. If it works, great, if not run the manufacturers drivers for it.

If it still causes a crash, likely it is caused by a conflict with another device. Use device manager to change resource options.

Also, some new USB HDD's have been found new, with a virus loaded. Wipe and format it when you have a chance, before use (be safe). Then run AV just to be sure (from safe mode)

by keithv

I tried a my old hard drive that still had windows xp pro installed on it and I had the same problem with the system rebooting. Im starting to think its a MB problem.

by keithv

Ok, I unplugged my usb hard drive and reinstalled the chipset drivers, checked the bios (legacy keyboard support enabled), USB V1 + V2 enabled. Rebooted. Plugged usb portable hard drive in and tried to copy 7 200MB files to it. About half way through the copy process the screen frooze and the system rebooted again . I just checked device manager and I dont see any conflicts and nothing is showing a yellow or red indicator. There are no viruses on my local hard drive or the usb drive.
Any other ideas would be greatly appreciated.

by keithv

Ok, I unplugged my usb hard drive and reinstalled the chipset drivers, checked the bios (legacy keyboard support enabled), USB V1 + V2 enabled. Rebooted. Plugged usb portable hard drive in and tried to copy 7 200MB files to it. About half way through the copy process the screen frooze and the system rebooted again . I just checked device manager and I dont see any conflicts and nothing is showing a yellow or red indicator. There are no viruses on my local hard drive or the usb drive.
Any other ideas would be greatly appreciated.

by keithv

Ok, I unplugged my usb hard drive and reinstalled the chipset drivers, checked the bios (legacy keyboard support enabled), USB V1 + V2 enabled. Rebooted. Plugged usb portable hard drive in and tried to copy 7 200MB files to it. About half way through the copy process the screen frooze and the system rebooted again . I just checked device manager and I dont see any conflicts and nothing is showing a yellow or red indicator. There are no viruses on my local hard drive or the usb drive.
Any other ideas would be greatly appreciated.

by keithv

I apologize for the multiple posts. The website kept giving me a 404 error but apparently it kept posting the message anyway.

by cg it

In start up and recovery.

That way, you won't reboot and you can use the task manager to end the program.

What shows in the event log?

if this is a straight copy, drive to drive,
then the system is having trouble communicating with the external drive.

Without research, it could be a USB device driver issue. Make sure you have the latest patches from both Windows and the device maker.

by the scummy one

I left the site for a few hours because of it.
Anyway, if you ge the 404 error, usually (not always) it will still post. What to do, is to hit the back button, copy your test, hit back again, and refresh. After the refresh you should see if it posted or not.

Back to your USB issue. Hmmm. It copies half of the data and then has an issue. As CGIT has mentioned, turn off auto reboot on errors.
It will either hang, or BSOD. The BSOD will give more info.
Also check the event viewer (as suggested) to see if any errors are listed.

Also, what happens if you copy smaller amounts of data. If it freezes in the middle of 7 200MB files, will it copy each 200MB file by itself? Or is it locking up and rebooting on a certain file?

Edited to add: If it errors on a certain file, the file is likely to be corrupt. If the file(s) are corrupt, run chkdsk /R /F

If it is erroring more randomly, back up your data before proceeding, because your main HDD may be having read issues, and may fail soon

by keithv

I checked the event viewer. The only error I found was this one. "The following boot-start or system-start driver(s) failed to load:
kl1"
I had kaspersky installed at one time but I uninstalled it a while ago. I dont think thats really causing the crashes.
I tried to run tuneup utilities drive check on the acomdata portable usb drive and I got the same reboot.
I can copy some files and then it will suddenly crash. Its not one particular file. Like I said earlier I also get the same problem sometimes accessing the flash memory card from my camera.
I installed the latest nvidia nforce 4 system drivers as well with no luck.
There are no apparent conflicts in device manager.
Where else should I look?
Also auto reboot has been disabled since before this problem started.
Thanks for everyones help.

by keithv

I tried running tune up utilities disk doctor and the system crashed. I tried the usb hdd on my notebook and it worked fine. That system runs xp pro as well. I ran the disk doctor from the notebook and it checked out fine. Im running out of ideas of what to check. Could it be a problem with the motherboard or is it definitely a windows issue?

by mayhem1969

heat. The two most common causes of restarts. This could be the result of a bad cpu...the more power required for the tasks such as moving files to a peripheral, the hotter the cpu gets and it restarts or if its bad it will restart spontaneously when too many requests are placed on it. 600 watts sounds plenty big enough, but if your ps is going bad you may not be pulling enough watts to run the system as configured.

by keithv

The temps seem good. I dont have any other problems with the system other then this. I would think if it was a PS problem or a CPU problem Id have other signs, no?
Its really got me stumped. Im pricing out a new MB and cpu because this has got me so frustrated.

by keithv

I reinstalled SP2 with no luck. I reinstalled the motherboard device drivers and nothing. I then reinstalled an old hard drive I had removed from this system that still had windows xp installed. I was able to access the drive with no problems at all. I copied files to and from the drive and scanned it, and it never crashed. I then reinstalled my current hard drive and had the same problem again. So it must be a windows problem. I tried comparing the printout from device manager from both drives and the only difference I noticed is the listing for ide ata/atapi controller. The controllers are listed differently on each drive. Would the ide controller effect the usb drive? I tried updating the drivers but I have the most recent versions already installed.
Any one have any ideas what to try next?
Thanks

by mayhem1969

It might not be the USB. What the problem may be is copying or transferring files from the current HDD. If the replacement transfers files to the USB HDD without issue, then it might not be windows, but the HDD itself.

I would think that if it was a windows issue a reinstall of XP and not just SP2 would resolve it. You might backup and then try a repair install or a complete reinstall. But if that doesn't resolve it, I doubt it's some spontaneous windows issue but most likely a failing HDD.

by keithv

but I can copy the same files to another internal hard drive with no problems and I can transfer the files via network, the problem only occurs when accessing the usb hard drive. it also crashes if I run tuneup utilities disk dr on the usb drive.

by mayhem1969

It seems you've done an exhausting search for the problem but still haven't found exactly what it is. I think you'll have to reinstall XP completely. Either you've got a device conflict, a virus or other malware, or simply downloaded an update automatically that interferes with the operation of your computer with peripheral devices.

I don't think the question is how are the two hard disks different, so much as how are the two windows XP OSs different. Different updates or different hardware configurations. When you changed the OS its possible that something else was sacrificed that allowed the USB HDD to work properly. That gives me the impression you may have a conflict. You might try uninstalling the devices and reinstalling them (it has been a while since I read the entire thread). But, you may have already tried that. Otherwise, I think you are looking at a complete reinstall to fix whatever windows problem you have.

by keithv

Thanks Mayhem, thats what Ive been trying to avoid if possible. Ive tried every utility I know of to try to find the conflict but no luck. I was hoping someone else out there ran into the same problem somewhere along the line.
The problem with the drivers is I dont even know where to start uninstalling. I cant find any info on what would cause a conflict with usb devices.

by mayhem1969

I don't think you indicated whether this was something recent that occurred or if it has existed since XP installed the devices as new hardware. Can you access the information on the drive from safe mode? If there is not a problem in safe mode, then it would appear to be a driver issue or driver conflict.

I think you said that you were using the most recent drivers for these devices? You might try going into device driver and removing the devices, rebooting and seeing if that helps. (you may have already tried this).

Since XP is updated there is no reason it should have a compatibility issue with these drives or your reader for that matter. However, you may have downloaded a recent update that interferes with your USB connections or simply had a corrupted system file.

I don't blame you for wanting to avoid a reinstall. You might try an in place reinstall which will not erase your information. Good luck.

by the scummy one

that I can think of. Sorry for being late to the party!

Go to start -- run -- sfc.exe /scannow

have the XP cd in the disk tray. This will take a while, but it may help.
Also, you may want to limit startup apps and running programs while doing the copy.

Aside from that, I am at a loss here and cannot think of another solution right now.

by keithv

I tried booting to safe mode and copying files to the drive and the same thing happened. The system froze and then rebooted.
Im completely lost here.
How would I do an in place resinstall?

by rob miners

There are a couple of other things to try before reinstalling.

Look for errors in the event logs.
To view the event log: Administrative Tools/Event Viewer or Start/Run/eventvwr.

As CG IT suggested.
By default when WinXP encounters a system failure, it reboots without warning. The setting that controls this can be changed:
Control Panel/System/Advanced/Settings (Startup & Recovery)/System Failure/Uncheck-Automatically Restart. When you get the Blue Screen take note of Stop: 0X00000000 and post the information it could give us a clue as to where to start looking.

There are also debugging tools available. If you look to the right of the screen when you click on this link you will find instructions.

http://www.microsoft.com/whdc/devtools/debugging/installx86.mspx

Symbols

http://www.microsoft.com/whdc/devtools/debugging/symbolpkg.mspx

by keithv

After running SFC.exe and rebooting I got the BSOD. I had to do a system restore to correct whatever sfc.exe did.
I have it set not to reboot on errors but it still does. Ive checked the event logs and there arent any errors listed.
Does anyone know if ultraiso, magiciso, or daemon tools could be the problem?
Ive tried disabling all virtual drives and that didnt help either.
I really appreciate everyone's help with this.

by rob miners

Was this Drive a Full Build or was it installed from an Image?

If you are using ultraiso, magiciso, or daemon tools how many Virtual Drives from each Application did you setup?
For example I use Magic ISO and Virtual Clone Drive. I dont install Magic Disk at the same time.

Here is a link to some good reading.
Have a look at this section. Cleanup the Device Manager / Windows Safe Mode

http://www.usbman.com/Troubleshooter%20General.htm

It wouldn't hurt to run this either. There is a free version.
http://www.memtest86.com/

Also when you have the cover off the PC have a look at the Capacitors. Check for bulging or leaking.

by the scummy one

There is no way to change the message limit on this board/thread, we all have to work within the limits.
When the max message level is hit there are 2 things that often get done. First is like this, go up 1 level and post to that. Many times we will add in the subject, a person to whom it is directed to.
The other way is to post under a different sub-thread, or the original post and continue from there.

by keithv

I tried running sfc.exe and it loaded all the drivers from the cd and then that was it. Nothing else happened. Im not sure what was supposed to happen after the progress bar finished.

by keithv

This drive was a fresh install when I got it. I have also installed SP2 and all the updates from Microsoft.
I only have 2 virtual drives set from daemon tools. I had tried disabling the virtual drives but that didnt help..
Im thinking about uninstalling all those utilities and trying it that way.
I will check out that page.
THanks. Ill keep you posted.

by Former member

You might wish to get a diagnostics suite and test your USB ports.

I have a Micro drive that is defective and if left in the port during a reboot, it will cause an endless reboot cycle. A faulty USB port destroyed the micro drive.

The point is that interaction of hardware can cause the problem that you have. Conflicting interrupt addresses can also do this.

by keithv

Any recommendations of what program or programs to try? Ive tried tuneup utilities and it didnt find any errors. There are no errors shown in device manager either.
Im thinking it must be a 3rd party software driver thats causing the problem. I just cant figure out which one.

by rob miners

the memtest results?

You say that you reinstated your old hard drive and everything worked. How have you got the jumpers configured on the drives? Are they both set as master or is one cable select?

by keithv

My internal HDDs are sata drives, each connected to its own port

by rob miners

which Drive had had the reference to ide ata/atapi controller?
Edit:

If it is the new one try this Workaround.

http://support.microsoft.com/kb/817472

Edit:
The reason I am thinking about this is because I don't think that the Drive has been picked up properly in XP.

by keithv

I think its recognized fine. I can access the drive. I can view the contents. Its just when I try to copy files to it that the whole system crashes.
Not sure what you are referring to about the controller though.
The old hard drive with windows xp had a different driver listed for the motherboard then the new hard drive with my current windows on it. Is that what you meant?

by rob miners

thats what I meant. I think its time for a rebuild. As Pond Scum suggested a few days ago go to a command prompt and run chkdsk /r
It will require you to resart the PC before it will do it.
Also go to the Drive Makers site and download any Disk Tools. Run them.
Other than that I am all out of ideas.
Have you ran memtest yet?

by keithv

All this time Ive been trying to copy files to the usb drive. Tonight I decided to copy from the drive to my HDD and it worked fine. I copied a number of files and there was no problem. I then tried to copy the same files back to the usb drive and the system crashed. Im even more stumped now then before. I have scanned my hdd and there are no problems shown. When I try to scan the usb drive the system crashes.
Can anyone explain this?
Thanks..

by the scummy one

the drive reads fine, but will not write without error.

Are you sure you have the correct power cable for the hdd?
currently, I am scratching my head, cause it works fine on another system. sfc kills your system, and reloading drivers and SP2 had no effect. The only thing I can think of is power issue to the drive. Try another power strip or wall plug.

by keithv

The same drive worked in this system with an older copy of windows though. So do you think it would be a power problem?
Do you know of any drivers that would effect copying to but not copying from? That even sounded wrong just writing it.

by the scummy one

so it must be some other conflict/bad driver, corrupt file, etc. in Win.

by keithv

Any other ideas of what to check? Or what utilities I could try to find the problem?
Thanks for everyone's help

by rob miners

we haven't asked is what file system are you using on the external Drives??

Edit:
The reason I ask is because I found a thread to do with Knoppix Live CD locking up when the external Drive was connected.

by rob miners

Create a Restore Point.

1. Go to Start -> Run and type cmd

2. In the DOS window, type the following, pressing ENTER after each line:
SC Stop KLIF
SC Delete KLIF
SC Stop kl1
SC Delete kl1

3. Close the DOS window & reboot the system

by keithv

Im going to try this but what is does it do? What am I stopping and deleting?
Thanks

by keithv

I had this turned off from the beginning but it doesnt seem to matter. The file copy animation freezes and the screen goes black and then reboots.

by rob miners

pretty obvious that something has became corrupted and I think that it is pretty serious if you can't get a Blue Screen. If you are not prepared to reinstall do the inplace repair and see how you go. If it works problem solved. If it dosn't you wont have much choice but to reinstall.

Happy New Year
Rob

by keithv

Only the KL1 service and file was left on my system. I removed it and tried copying files. As usual it copied about half way and then reboot.
Is there a utility to somehow trap the error thats causing the reboot?

by rob miners

Post 28 has the instructions. It would have been one of the first things that I would have checked.

You did restart the PC after removing the KL1 service?

by keithv

ok. I installed the debugging tools. Now what? Im not sure where to start

by rob miners

If you installed symbols to the default directory. Create a batch file and run this command substituting Mini122707-02.dmp with the name of your minidump file which if you have one is at C:\WINDOWS\Minidump

dumpchk.exe -y "srv*c:\windows\symbols*" C:\WINDOWS\Minidump\Mini122707-02.dmp > C:\output.txt

I really think that you should try the Inplace Repair as Pond Scum suggested. You should be able to turn off autorestart to Blue Screen.

by keithv

Thank you for all your help. I wish I could figure out whats causing the problem but its not looking like its going to happen. I guess my only option is a full reinstall.

by rob miners

really don't want to keep dragging this on but what was the result from the Debug.

by keithv

I couldnt figure out how to run the debug. If you could give me some guidance on that I might be able to find something.
THanks

by rob miners

If you installed symbols to the default directory.

Create a batch file and run this command substituting Mini122707-02.dmp with the name of

your minidump file which if you have one you will find it in C:\WINDOWS\Minidump

Open notepad and copy and paste the information between the == == to notepad.

===================================================================================

dumpchk.exe -y "srv*c:\windows\symbols*" C:\WINDOWS\Minidump\Mini122707-02.dmp >

C:\output.txt

======================================================================================

Note this is one line of text.

Modify the file to reflect the name of your Minidump file.

C:\WINDOWS\Minidump is where you will find the file.

Save the file as c:\dpchk.cmd

Open Explorer and navigate to the C:\ Drive

find your new file and run it.

Then open C:\output.txt

It will look something like this result from running 2 instances of siw.exe from a flash drive.

----- 32 bit Kernel Mini Dump Analysis

DUMP_HEADER32:
MajorVersion 0000000f
MinorVersion 00000a28
DirectoryTableBase 00039000
PfnDataBase 81b83000
PsLoadedModuleList 8055b140
PsActiveProcessHead 80561258
MachineImageType 0000014c
NumberProcessors 00000001
BugCheckCode 1000007e
BugCheckParameter1 c0000005
BugCheckParameter2 805a7085
BugCheckParameter3 f78cabac
BugCheckParameter4 f78ca8a8
PaeEnabled 00000000
KdDebuggerDataBlock 8054cd60
MiniDumpFields 00000dff

TRIAGE_DUMP32:
ServicePackBuild 0c850300
SizeOfDump 00010000
ValidOffset 0000fffc
ContextOffset 00000320
ExceptionOffset 000007d0
MmOffset 00001068
UnloadedDriversOffset 000010a0
PrcbOffset 00001878
ProcessOffset 000024c8
ThreadOffset 00002728
CallStackOffset 00002980
SizeOfCallStack 000003f0
DriverListOffset 00003000
DriverCount 00000081
StringPoolOffset 00005650
StringPoolSize 000011b0
BrokenDriverOffset 00000000
TriageOptions 00000041
TopOfStack f78cac10
DebuggerDataOffset 00002d70
DebuggerDataSize 00000290
DataBlocksOffset 00006800
DataBlocksCount 00000005

Windows XP Kernel Version 2600 (Service Pack 3, RC 12.133) UP Free x86 compatible
Kernel base = 0x804d7000 PsLoadedModuleList = 0x8055b140
Debug session time: Fri Oct 19 07:38:34 2007
System Uptime: 0 days 1:34:16
start end module name
804d7000 806ed400 nt Checksum: 00221856 Timestamp: Sat Sep 01 03:21:45 2007 (46D84E29)

Unloaded modules:
b6172000 b6175000 SiwIo.sys Timestamp: unavailable (00000000)
f79ef000 f79f1000 cpuz_x32.sys Timestamp: unavailable (00000000)
b5ef7000 b5f22000 kmixer.sys Timestamp: unavailable (00000000)
b670d000 b6738000 kmixer.sys Timestamp: unavailable (00000000)
b6738000 b675b000 aec.sys Timestamp: unavailable (00000000)
b9457000 b9458000 drmkaud.sys Timestamp: unavailable (00000000)
b6a0f000 b6a1c000 DMusic.sys Timestamp: unavailable (00000000)
b6890000 b689e000 swmidi.sys Timestamp: unavailable (00000000)
b6ba5000 b6ba7000 splitter.sys Timestamp: unavailable (00000000)
f7527000 f7530000 processr.sys Timestamp: unavailable (00000000)
f780f000 f7814000 Cdaudio.SYS Timestamp: unavailable (00000000)
f793b000 f793e000 Sfloppy.SYS Timestamp: unavailable (00000000)
f7807000 f780c000 Flpydisk.SYS Timestamp: unavailable (00000000)
f77ff000 f7806000 Fdc.SYS Timestamp: unavailable (00000000)

Finished dump check

by keithv

There isnt a minidmp file for every time the system rebooted due to the usb hard drive problem. Not sure why that is. Here is what I got though. Hope you know how to read it. :-)

----- 32 bit Kernel Mini Dump Analysis

DUMP_HEADER32:
MajorVersion 0000000f
MinorVersion 00000a28
DirectoryTableBase 0ba70060
PfnDataBase 82000000
PsLoadedModuleList 8055c700
PsActiveProcessHead 80562818
MachineImageType 0000014c
NumberProcessors 00000002
BugCheckCode 1000008e
BugCheckParameter1 c000001d
BugCheckParameter2 00000047
BugCheckParameter3 a8cab540
BugCheckParameter4 00000000
PaeEnabled 00000001
KdDebuggerDataBlock 8054c2e0
MiniDumpFields 00000dff

TRIAGE_DUMP32:
ServicePackBuild 00000200
SizeOfDump 00010000
ValidOffset 0000fffc
ContextOffset 00000320
ExceptionOffset 000007d0
MmOffset 00001068
UnloadedDriversOffset 000010a0
PrcbOffset 00001878
ProcessOffset 000024c8
ThreadOffset 00002728
CallStackOffset 00002980
SizeOfCallStack 00000ab0
DriverListOffset 000036c0
DriverCount 0000008e
StringPoolOffset 000060e8
StringPoolSize 000013c8
BrokenDriverOffset 00000000
TriageOptions 00000041
TopOfStack a8cab550
DebuggerDataOffset 00003430
DebuggerDataSize 00000290
DataBlocksOffset 000074b0
DataBlocksCount 00000006

Windows XP Kernel Version 2600 (Service Pack 2) MP (2 procs) Free x86 compatible
Kernel base = 0x804d7000 PsLoadedModuleList = 0x8055c700
Debug session time: Sat Dec 29 12:43:44 2007
System Uptime: 0 days 0:00:27
start end module name
804d7000 806e2000 nt Checksum: 001FB950 Timestamp: Wed Feb 28 04:15:54 2007 (45E5484A)

by rob miners

Follow this link for instructions on using Windbg.
If you downloaded Symbols point it to that folder.
When you have ran the initial dump if you look to the bottom of the screen you will see kd> to the right of that type in !analyze -v and press the Enter key.

Ctrl + a will copy the information and paste it into notepad.

As there will be a lot of info pm me the results.

http://forums.majorgeeks.com/showthread.php?t=35246

by keithv

Microsoft (R) Windows Debugger Version 6.8.0004.0 X86
Copyright (c) Microsoft Corporation. All rights reserved.

Loading Dump File [C:\WINDOWS\Minidump\Mini122907-02.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: C:\WINDOWS\Symbols
Executable search path is:
Unable to load image ntoskrnl.exe, Win32 error 0n2
*** WARNING: Unable to verify timestamp for ntoskrnl.exe
Windows XP Kernel Version 2600 (Service Pack 2) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Kernel base = 0x804d7000 PsLoadedModuleList = 0x8055c700
Debug session time: Sat Dec 29 12:43:44.203 2007 (GMT-5)
System Uptime: 0 days 0:00:27.875
Unable to load image ntoskrnl.exe, Win32 error 0n2
*** WARNING: Unable to verify timestamp for ntoskrnl.exe
Loading Kernel Symbols
.............................................................................................................................................
Loading User Symbols
Loading unloaded module list
..
ERROR: FindPlugIns 8007007b
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 1000008E, {c000001d, 47, a8cab540, 0}

*** WARNING: Unable to verify timestamp for ati2dvag.dll

Probably caused by : ati2dvag.dll ( ati2dvag!DrvEscape+318 )

Followup: MachineOwner
---------

0: kd> !analyze -v
ERROR: FindPlugIns 8007007b
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

KERNEL_MODE_EXCEPTION_NOT_HANDLED_M (1000008e)
This is a very common bugcheck. Usually the exception address pinpoints
the driver/function that caused the problem. Always note this address
as well as the link date of the driver/image that contains this address.
Some common problems are exception code 0x80000003. This means a hard
coded breakpoint or assertion was hit, but this system was booted
/NODEBUG. This is not supposed to happen as developers should never have
hardcoded breakpoints in retail code, but ...
If this happens, make sure a debugger gets connected, and the
system is booted /DEBUG. This will let us see why this breakpoint is
happening.
Arguments:
Arg1: c000001d, The exception code that was not handled
Arg2: 00000047, The address that the exception occurred at
Arg3: a8cab540, Trap Frame
Arg4: 00000000

Debugging Details:
------------------

EXCEPTION_CODE: (NTSTATUS) 0xc000001d - {EXCEPTION} Illegal Instruction An attempt was made to execute an illegal instruction.

FAULTING_IP:
+47
00000047 ?? ???

TRAP_FRAME: a8cab540 -- (.trap 0xffffffffa8cab540)
ErrCode = 00000000
eax=00000086 ebx=bfa11601 ecx=00000000 edx=e2ad4f98 esi=a8cab60c edi=e2664538
eip=00000047 esp=a8cab5b4 ebp=e25d5008 iopl=0 vif nv up ei ng nz ac po nc
cs=0008 ss=0010 ds=0023 es=0023 fs=0030 gs=0000 efl=00090292
00000047 ?? ???
Resetting default scope

CUSTOMER_CRASH_COUNT: 2

DEFAULT_BUCKET_ID: DRIVER_FAULT

BUGCHECK_STR: 0x8E

PROCESS_NAME: csrss.exe

LAST_CONTROL_TRANSFER: from e2664538 to 00000047

FAILED_INSTRUCTION_ADDRESS:
+47
00000047 ?? ???

SYMBOL_ON_RAW_STACK: 1

STACK_ADDR_RAW_STACK_SYMBOL: ffffffffa8cab644

STACK_COMMAND: dds A8CAB644-0x20 ; kb

STACK_TEXT:
a8cab624 8b138f18
a8cab628 00000000
a8cab62c 00000000
a8cab630 00000000
a8cab634 00000000
a8cab638 eefc0000
a8cab63c bfa083d0 ati2dvag!_NULL_IMPORT_DESCRIPTOR (ati2dvag+0x333d0)
a8cab640 bf9f0d88 ati2dvag!DrvEscape+0x318
a8cab644 00000000
a8cab648 896a296c
a8cab64c a8cab66c
a8cab650 bf9f4191 ati2dvag!DrvGradientFill+0x9af
a8cab654 a8cab688
a8cab658 bfa130d0 ati2dvag!_NULL_IMPORT_DESCRIPTOR (ati2dvag+0x3e0d0)
a8cab65c 00000001
a8cab660 00000000
a8cab664 00000004
a8cab668 00000001
a8cab66c a8cab6bc
a8cab670 bf9f4a33 ati2dvag!DrvDisablePDEV+0x111
a8cab674 00000005
a8cab678 a8cab688
a8cab67c 8b138038
a8cab680 00000000
a8cab684 a8cab7c4
a8cab688 e26741b0
a8cab68c e2ab2440
a8cab690 e2ab2314
a8cab694 8b138038
a8cab698 e2ac8080
a8cab69c 00000130
a8cab6a0 0000012c

FOLLOWUP_IP:
ati2dvag!DrvEscape+318
bf9f0d88 ?? ???

SYMBOL_NAME: ati2dvag!DrvEscape+318

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: ati2dvag

IMAGE_NAME: ati2dvag.dll

DEBUG_FLR_IMAGE_TIMESTAMP: 452d9de8

FAILURE_BUCKET_ID: 0x8E_BAD_IP_ati2dvag!DrvEscape+318

BUCKET_ID: 0x8E_BAD_IP_ati2dvag!DrvEscape+318

Followup: MachineOwner
---------

by keithv

The only thing is that this page makes no mention of this affecting on usb hard drives. Other then that problem my system is rock solid.Im going to give it a shot anyway though and see what happens.
Ill let you know

by keithv

I uninstalled all my ati drivers and reinstalled the new omega drivers. Tested my usb drive and same problem, instant reboot and no minidmp file.
Completely frustrated at this point I found an old pci usb 2.0 add in card. I figured Id try it. I installed the card, connected the drive and it works perfectly. Ive copied about 10gig back and forth from the drive over the past hour testing it.
Now I have no idea why the add in card works but the on board usb ports dont. I would think its a driver issue but my old hard drive that I took from this system when I upgraded worked fine.
Im happy its working now but Id still like to know whats causing the problem.
Thanks for all you help. Maybe someday I can return the favor.

by rob miners

the problem is the ati2dvag drivers somehow conflicting with the onboard USB. My next step would be to try another Video Card preferably not the same make. Then you will know for sure whether or not it is the card.

by keithv

Unfortunately the only PCIe cards I have are ATI. I have an old AGP card but that wont go int this system. The onboard usb works fine for printing, my mouse, and my gaming keyboard. Its definitely got to be a conflict. I'm going to try reinstalling the old hard drive and see if I can figure out what I didnt have installed on that one that I do now. Ill keep you posted on what I find.

This discussion is closed to new replies.