Question Locked

TDK 440N DVD RW does not recognise CD disks

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am hoping someone has an answer to my dilemma.

I have a TDK 440N DVD R/RW drive that has stopped recognizing CD disks.

I have tried using a bootable disk and it will not boot to the disk.
I have upgraded the firmware.
I have re-installed the drivers.
I have replaced the ribbon cable.
I removed and then re-installed it.

It shows up with the correct designation and will burn DVD?s with no qualms but cd?s just show as an empty volume.

If anyone can shed some light on this I would greatly appreciate it.

10 replies

by Former member

You might need to reset the drive to its original driver by putting a pin in the reset slot that you should find on the drive. This resets the drive back to its default state.
I hope this helps you.

by grrr_its_tuffy

Hey Alan, have you had any luck with your CD problem? I'm having the same trouble. It recognizes DVDs and DVD disks used for data, but not data CDs, audio CDs or blank CDs. Actually it *DOES* recognize CDs *IF* I uninstall the drive from the Device Manager and then restart. But when I do this it only works the first couple of times I insert disks. Then it stops recognizing them again.

I figured one of the drivers must be corrupt or something, so I tried reinstalling the system and it still does it. I also reinstalled TDK's "Disc Blender" software which is supposed to include drivers. No luck.

I don't think it could be a firmware problem because these are disks I've had around for a while, and I believe firmware upgrades just get the drive to recognize newer media...? But I can't see how it could be mechanical with the way it's acting.

Have you tried uninstalling the drive like I did? Did it react the same way? I'm hesitant about trying Peconet's reset-slot solution because I think that would just duplicate what I've already tried. But I've searched all over for solutions to this and I'm stumped.

by alan

Well I tried a number of solutions but the one that eventually worked was I replaced the drive.

None of the other solutions I found worked at all. I upgraded the firmware, removed then re-installed it, found the latest drivers, and nothing worked. I even installed it into another system and the problem happened there too.

The new drive is working perfectly.

by grrr_its_tuffy

So I get to buy a new drive now! Yay. Sure is a bizarre problem though, isn't it?

by scttgrswld

A similar thing is happening to me and others that i know some discs don't boot properly. in my case and with others i know also (note: they have differnt name brade drives).

I have noticed with newer disks recently purchased or attained have problems being recognized by my 440n, my older ones that have always booted, still boot fine. So it could only really be one of the following reasons:
1. Drive Gone bad (works fine with older disks though)

2. More modern program disks made differently and drive can't always recognize them properly. (I say "not always" because some of these new ones eventually after multiple tries load up) Maybe TDK needs to give better driver updates to keep it current with current disk making techniques.

3. There is a virtually undetectable macro virus/bug out there causing this to happen since I've seen this problem spread out among different brand name drives (most have been older drives though)

through my experience with this problem and now coupled with yours and your efforts to resolve the problem eventually getting a new drive which I assume is working fine now makes me lean toward reason #2 maybe #3 but if it is 3 then the bug only affects older units I'd bet though it's 2 after all why should companies such as tdk give us proper support for our old working units when they can prosper on selling us new ones? :(

by dave.lee

I just pulled a 440N out of a recycle pile. "Dead-for recycling" was markered on the case top. Plugged it into a 2 year old HP Compaq and watched "Princess Diary" and then listened to a cd copy of "The Roches". XPSP2 identified it and let me right in. Sorry. Have a better day.

by oh smeg

The Dyes used in making the new Disc's are not 100% Compatible with the Wavelength Laser used in this Old CD Burner.

If the Light is not reflected fully the Reader may not be able to read the Disc's reliably. This was once a very common thing when the First CD Burners became available some makers in an attempt to guarantee future income required that you buy their Blank Media. This worked quite well till Places like Kodak stopped making any media and then the Kodak Burners became useless as a Burner as there where no Blanks that they could successfully burn.

The other thing with Optical Burners is if you leave Disc's in them all the time the Intensity of the Laser Light drops off as the LED's used to generate the light start to break down or degrade. You should not leave Disc's in an Optical Drive indefinitely. If you need to use a single Disc a lot or need it in a Optical Drive you should load a Virtual CD Application and copy it to the HDD instead of using a CD.

Col

by bakerst

The CD only drive on my Dell Optiplex at work failed right after tech services upgraded MS Office from 2003 to 2007. The upgrade was pushed from a server. They replace the CD drive to fix the problem.

At home my Dell Inspiron with the TDK 440N stopped recognizing any CDs period right after I upgraded MS Office 2003 to 2007 from the MS Home Edition CD. The drive worked for the upgrade, but only reads DVDs ever since.

This discussion is closed to new replies.