Question Locked

The MOBO... how can I be SURE it's really the problem?

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Not certain if it's the mobo, psu, or video card. I'm working on a friend's factory HP a6303w with an Asus IPIBL-LB mobo (with no led indicator) and a 300 watt psu. Sometimes within 10 seconds of start up, it will shut itself down momentarily then power back up and stay on. I get NO beeps, even with EVERYTHING disconnected. The fans come on, and all devices have power, but nothing responds. The monitor will say no signal and go to sleep and won't wake up. the keyboard may or may not flash but never powers on up. The dvd drive will open and close but never sounds like it's spinning/reading.

I have swapped memory, cleared cmos, replaced the battery, and reset the psu. I tried contacting both HP and ASUS, but frankly, they were useless.

17 replies

by oh smeg

Than replace the PS. These things use at least 3 different Voltage Rails and if one is down while the unit may seem to work it's not either getting enough or any power to at least one of those circuits.

By the sounds of your description it sounds as if either the 5 V DC or 1.3 V DC rails are either not producing any Voltage or are way down on current. Replacing the PS may get it working again but it is just as likely that the Faulty PS has taken the M'Board along for the ride and if this has a AMD CPU I would expect that as well to be no longer working.

It's just that the AMD Chip Sets don't seem to isolate the CPU's as well as Intel Chip Sets do from nasty things happening. ;)

Col

by twilazoned

Thanks for the fast response!

I had just returned to find your response after replacing the ps with two diff ones, but each had the same result. When I press the power button, everything comes on strong, lasts a few seconds, powers down like it's dead for about 3 seconds, then boots back up and stays running. Still, none of the devices actually WORK, they just have power.

I did notice that her heat sink was totally gunked up. I cleaned it, the cpu (Intel, btw), and reapplied some fresh thermal grease. Wondering if it got overheated after seeing how thick as the gunk was.

Also noticed that the hdd led doesn't flicker at all after the second power up. It just stays solid.

What gets me is that she bought it new, and the factory warranty expired last month. She drives a truck cross country for a living, and it's seldom used since she's rarely home. It was working fine when she left for her last job, but when she came back a week later and powered it up, nothing.

I just want to make sure it IS the mobo before I have her shelling out that kind of money.

by peconet tietokoneet

The first port of call to me would be the processor, but you have cleaned that. By the way did you apply a very,very small amount of thermal paste to the processor? With that done the second would be the power supply unit.
Another thing you can try out.. IS the computer in question Overclocked? Have a look in the BIOS and then select "Default settings", then "save and exit".
If that does not work then a new motherboard will be the next choice.

by ---tk---

I would look all over the Mombo for a blown compositor... If you find a "popped cap" that could and would cause this issue. They are the little cylinder looking things with a "x" on top. They should be level, not bumped up, or worse case leaking acid.

you can google "Popped cap" (Images) and find what they can look like if you have never seen it before.

Added: I should have read Jacky Howe's post before posting...

by dpalsen

Easiest way to tell if it's the PSU is to look at the BIOS and check if your CPU is overheated, as in most modern BIOSes, it will tell you. If it isn't POSTing, are there any beep codes, or is there any way to look at the MOBO and find a troubleshooting light or some such.

As for it powering back on with the HDD LED not coming on, try unplugging all of the drives, and see if it will at least make it past POST. The other thought is to try a video card, but I'm REALLY skeptical that that would be the problem. I'm really leaning motherboard on this one.

by rob miners

Check the Capacitors around the CPU for swelling or bulging. They should have a flat head with a cross indent.

by rob miners

and it's starting and running I wouldn't suspect the CPU. They normally work or they don't.

Carefully remove everything from the Motherboard. Remove the Motherboard and put it on an anti-static mat on a bench. Remove the Power Supply if it is a known working good one to test with. Remove the Heatsink and give it a good clean. Remove the CPU and reseat it. Reinstall the Heatsink remembering to use CPU grease. Clean the golden edge of each memory stick and the video card with a soft rubber/eraser, remembering not to touch the golden edge. Reseat the RAM and test with one stick at a time. Connect the Video Card. Connect the Power supply to the Motherboard. You can use a flat blade Screwdriver to short the Power pins on the Motherboard if you haven't got a spare switch. Connect the Monitor and turn it on and see what happens. If it stars up add one Device at a time to test it. If it doesn't then the Motherboard has failed.

by twilazoned

Oh yes, I reapplied the grease, but unless there is a way to find out without reading a monitor, I have no idea if it's overclocked. When it starts up, the monitor says no signal, going to sleep. (and yes, i put in a new video card to tbs)

by oh smeg

You can look at the Jumpers on it or Clear the BIOS to remove any Overclocking that may have been present. Though if the M'Board CPU has suffered because of Overclocking it will not undo any of the damage. ;)

Col

by twilazoned

Had never heard that term before! Actually, I did go back and take a detailed look at them after you and Jack's suggestion, however, they all look fine.

by twilazoned

I am almost traumatized by her HP. I finally realized that I wasn't hearing any post codes because there was no on board speaker installed on her pc! Add to that NO led on the mobo, and the realization that it was put out with a cheesy 250 w ps, and I find I have never been so disappointed in an HP product.

Asus doesn't even have support for the mb (because it's OEM) and the support guy (who was really cool btw) helped me out anyhow and said the only things left would be that's it's either grounding out or fried.

About to pull that puppy out and see if it'll bark on a sheet of cardboard...

by ic-it

If it is one of the older AMD sockets (939) you may find a decent price at ascendtech.

I just replaced one this last weekend (HP AMBERINEM-GL6E S.939 2000FSB MBOARD, 5188-2526) 75.99 If it is the same style, be aware that the MB next to it (same page, bottom left and right) is the same but with composite out. (if not still a good source for other boards).

http://www.ascendtech.us/index.asp?FSCat=302&url=IND&iFromFeatured=1

Edited to add; You can find cheaper 939 boards, but this saved me hours by not needing to do a repair, updates, ect.

by twilazoned

I truly appreciate the assist on this one guys! I have never had a pc give me so much grief. And of course since it's an HP and is going to be tattooed, I'll be making a new post about THAT subject! (sigh...)

by rob miners

and let us know if you get code purple.

Edit: spelling

by wiseassowlx

I have a Hp pavillion p6212f which also has a IPIBL-LB and 250w power supply and there are so many different problems with it that I dont know where to start but the PSU is as good as any. when I ran the system ona couple of sites to estimate the proper psu to get I came up with 4oow and that wasn't even counting all the expansion slots being used or all 6 usb's drawing power. I just estimated moderately. I think that Hp turned out a lot of systems with underpowered pc's being the end result. to solve the dilemna then diffferent features are turned off to save power. features like screen resolution possibly and anyplace they can cut back just a smidge of power . they are running that tight. So features neve work or look right and if you change the settings its as if they are switched back to the economy settings anyways. And as far as the beeps you were expecting to hear to signal something being wrong I believe that i have seen data saying that some of these can be set to silent so it wont be recognized as a problem to the user. its a way of hiding a problem from the user just the same as archiving a message if its bringing bad news about a program or issue. Archive it and they will forget about it. anyway to make it appear as if there is no problem existing. Another example is Windows Error Reporting. this program can be shhut down so that no problem reports will be sent to Windows so then a computer that is problem riddled will suddenly appear to be ok even though it just doesn't run right. they are good at this. So then when you call tech support they cant understand why you are saying there is a problem.

This discussion is closed to new replies.