Question Locked

trouble connecting linksys wireless b adapter to linksys access point

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
My wireless b adapter can see my wireless access point but is unable to connect to it. I can connect to an outside apple unsecure network but can't connect to my own access point. I have wpa security, all my other computers can connect to the access point (laptop and IMAC); however, this desktop pc is unable to connect. Any help would be appreciated. I've downloaded the latest drivers for my linksys wireless b, ver. 2.8. Thanks!

12 replies

by langlier

You'll need to check a few things on the wireless router. Your default ip for it is 192.168.0.1 .(the default login/pass varies by router but if it is also a linksys leave the login blank and the pass is admin) type that into IE on anything that can connect to the router. verify that the router is operating to support both B and G and you may want to check to see if there is a new firmware available that may be able to eliminate some connectability issues. Its a start and further help can be provided if needed.

by clin

I have the latest firmware and my access point is set to mixed mode. Any other suggestions? Thanks!

by langlier

More suggestions:

If you are using the linksys connect tool disable it and use the Windows wireless connect tool

Make sure there is no other software installed (firewall, other wireless tools) that might interfere. If there is either disable or uninstall it.

It sounds like a client side problem. Thus it could be anything from the hardware to the software. If this was my tech shop I'd pop a USB wireless device into the desktop and see if I could connect with that.

by vinitogupta

Hi,
I have faced this problem once and i figured the solution actually I have in my personal network One Dlink router one linksys router 3 Desktop Machines and one Laptop, I am using two desktops on Linksys and one on Dlink, I use laptop for wireless connection with linksys and i had DHCP enabled in my linksys router. The ip was conflicting with one of the desktop, so i manually reconfigure the ip of my laptop and good to go

thanks

by clin

Thanks to all for your solutions. I am up and running again. I think there were multiple threads that needed fixing. I set the IP for the wireless desktop outside the range of both the router and access point. I made sure the subnets matched and the gateway and dns reflected the router. Now, it looks like I have a connection that doesn't drop. Thanks again.

Cathy

by clin

Thank you for your suggestions. I disconnected the linksys tool and took off the firewall. I also created a static IP from my dlink router for the PC based on its Mac address. The windows wireless connect tool says that I'm connected (low signal), yet, the signal comes and goes. I tested the adapter on my other pc and basically it sees the linksys access point but not the router to the outside internet.

I agree it's a client side issue, but I'm at a loss on how to proceed. Thanks for any help.

by rkuhn040172

I've seen LinkSys routers combined with DLink AP's (or vice versa) where for some unknown reason, the LinkSys will be on one subnet and the DLink will be on another.

The problem shouldn't happen and only happens on particular models.

One way to check is open up the router's management console and check the subnet settings or check a PC connected to the router using ipconfig /all.

Then, ipconfig /all on the PC in question that can't connect to the router but does connect to the AP.

I'd bet you have 2 different subnets going.

Like I said, it shouldn't happen but does.

BTW, the default settings for LinkSys equipment is 192.168.1.0 and DLink is 192.168.0.1.

Another poster in here had that wrong.

by clin

I fixed the IP of the access point and set the subnet as the same as the router. So my access point has a static IP within the range of the router's IP DHCP addresses. Would it be better if the IP of the access point was out of the IP range of the router? What's odd is that two of my other machines (IMac and husband's laptop) have no problem hitting the access point and then getting an IP from the router out to the internet. Thanks!

by langlier

Default linksys router is 192.168.1.1

I forgot they are the oddballs of the router world. most others are 192.168.0.1

This discussion is closed to new replies.