Discussion Locked

VFAI Failed(windows95)

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

While booting Windows 95 this message appeared.
VFAI Device Initialization Failed
A device or resource required by VFAI is not present or is unavailable. VFAI cannot continue.
Loading System Halted.
Is this a windows or hard drive issue?
Are you familiar or know what this message means?

8 replies

by talli

See, I believe u made a typo there-it should be "VFAT Device Initialization Failed", not "VFAI".Doesn't it make more sense? :)
Now, this nasty error could result from a number of conditions: 1. Your Ifshlp.sys file could be missing from your Windows folder. If that is true-extract a new copy from your original CD. 2. Your Config.sys could be pointing to a previous instance of that Ifshlp.sys file. In that case ,u should edit the Config.sys-go to Safe Mode Command Prompt and open Config.sys in any text editor u use (like Edit.com). Find the line that loads this file and delete it. (no worries-Windows looks for it automatically on bootup).Obviously, save the Config.sys and reboot. 3.It could be the opposite-that your Ifshlp.sys statement was removed from Config.sys (like when reinstalling Windows). In that case-also go to Safe Mode Command Prompt and edit Config.sys, only if u do not see any Ifshlp.sys statements-add one. (DEVICE=C:\WINDOWS\IFSHLP.SYS) (No brackets, obviously, and if your location of Windows folder is for some reason different-change it accordingly). 4. It could be that u have a bad Paths section of MSDOS.SYS. Go to edit it the same way (don't forget to change it's attributes in the beginning and restore them afterwards.)Your Paths section should look like this:
[Paths]
WinDir=
WinBootDir=
HostWinBootDrv=C
(WindowsFolder is obviously your Windows folder ,and, if u r using compression, instead of C-the letter of the host drive)
5. Ther could be a Winboot.ini file in root dir of your boot drive. To delete it go to Safe Mode CP and issue the following command:
deltree winboot.ini
To get into Safe Mode CP-use your boot floppy.
HTH
Good luck.
Talli

by mariahchrista

YOU HAVE A VERY DETAILED ANSWER AND IT SOUNDS LIKE YOU KNOW WHAT TO DO WITH ANY PROBLEM YOU MAY COME ACROSS. WE FINALLY FOUND THE RECOVERY DISC AND IT RAN IN SAFE MODE. THEN WE ADJUSTED THE MAX. CACHE SIZE. THANKS.

by maxwell edison

"VFAI" refers to an artificial intelligence or mathmatical analysis program. I'm going to assume that it's a typo, and your error message says, "VFAT Device Initialization Failed".

This problem can occur under any one of the following conditions:

1. If the Ifshlp.sys file is missing from the Windows folder.

2. If the Config.sys file contains a line that points to a
previous version of the Ifshlp.sys file.

3. If the following Ifshlp.sys statement is deleted from theConfig.sys file after you reinstall Windows:

DEVICE=C:\Windows\Ifshlp.sys

4. If the [Paths] section in the Msdos.sys file is incorrect.

5. If a Winboot.ini file from a previous incomplete installation
is present in the root folder on your Startup disk.

6. If a "maxfile cache = 4096" line is present in the System.ini
file.

-------------------------------------------------------------------
(1.) To resolve the problem, use one of the following methods.
-------------------------------------------------------------------

Ifshlp.sys File Missing from Windows Folder
-------------------------------------------

If the Ifshlp.sys file is missing from the Windows folder, extract a new copy of the file from your original Windows floppy disks or CD-ROM to the Windows folder.

For information about how to use the Extract tool, view the following article in the Microsoft Knowledge Base:

Q129605 How to Extract Original Compressed Windows Files (go to the Microsoft support web site & search Q129605)

-------------------------------------------------------------------

(continued in comments....)

by maxwell edison

(2.) The Config.sys File Points to a Previous Version of the
Ifshlp.sys File
-------------------------------------------------------------------

1. Restart your computer. When you view the "Starting Windows 95"
message, press F8, and then choose the Safe Mode Command Prompt
Only option from the Startup menu.

2. Use a text editor (such as Notepad) to open the Config.sys file.

3. Delete the line that loads the Ifshlp.sys file. Note that Windows
automatically loadsthis driver when you start your computer.

4. Save and then close the Config.sys file.

5. Restart your computer.
(3.) Ifshlp.sys Statement Was Deleted from the Config.sys File
After You Reinstalled Windows
-------------------------------------------------------------------

When you reinstall Windows, the Ifshlp.sys statement is deleted from the Config.sys file and it is not replaced. To add the Ifshlp.sys statement to the Config.sys file:

1. Restart your computer. When you view the "Starting Windows 95"
message, press F8, and then choose the Safe Mode Command Prompt
Only option from the Startup menu.

2. Use a text editor (such as Notepad) to open the Config.sys file.

3. Type the following line in the Config.sys file:

DEVICE=C:\Windows\Ifshlp.sys

4. Save and then close the Config.sys file.

5. Restart your computer.

(continued in next comments....)

by maxwell edison

.
.(4.) Incorrect [Paths] Section in the Msdos.sys File
-----------------------------------------------

1. Restart your computer. When you view the "Starting Windows 95"
message, press F8, and then choose the Safe Mode Command PromptOnly option from the Startup menu.

2. Type the following command at a command prompt:

" attrib -s -h -r msdos.sys " (without the quotation marks)

3. Use a text editor (such as Notepad) to open the Msdos.sys file.

4. Verify that the following lines in the Msdos.sys file are correct [Paths]
WinDir= WinBootDir= HostWinBootDrv=C where
is the folder that contains Windows. Note that if you are
using disk compression software, you must change thedrive letter in the
HostWinBootDrv= line to the drive letter of the host drive.

5. Save and then close the Msdos.sys file.

6. Type the following line at a command prompt:

" attrib +s +h +r msdos.sys " (without the quotation marks)
7. Restart your computer.

-------------------------------------------------------------------

by maxwell edison

.
.
(continued from previous comments...)(5.) Winboot.ini File Present in the Root Folder of the Boot Drive
-------------------------------------------------------------

1. Restart your computer. When you view the "Starting Windows 95"
message, press F8, and then choose the Safe Mode Command Prompt
Only option from the Startup menu.

2. Type "deltree winboot.ini" (without the quotation marks) at a
command prompt to delete the Winboot.ini file in the root folder
of the boot drive, and then press ENTER.

3. Restart your computer.

-------------------------------------------------------------------
(6.) There Is a "maxfile cache = 4096" Line in the System.ini File
-------------------------------------------------------------

Use any text editor (such as Notepad) to open the System.ini file in the Windows folder. Type a semicolon (";" (without the quotation marks)) at the beginning of the "maxfile cache = 4096" line, save the file, close the file, and then restart your computer.

I hope this helps. Good luck.

Maxwell

by mariahchrista

YOUR INFORMATION IS VERY DETAILED AND IT SOUNDS LIKE YOU KNOW WHAT TO DO IN BINDS. UNFORTUNATELY IT DIDN'T HELP AND I DON'T KNOW WHY. AFTER SEARCHING WE FINALLY FOUND THE RECOVERY DISC AND THAT RAN IT IN SAFE MODE. WE THEN GOT HELP AND ADJUSTED THE MAX. CACHE SIZE.

This discussion is closed to new replies.