Discussion Locked

VPN w/ Linksys, Cisco, NT 4.0 Server

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,

I've searched high and low and can't figure this out, but I also noticed that there are probably many members out there with the same setup. I have a Cisco 67x router connected to a Linksys BEFSR41. The Linksys provides the DHCP, NAT, IPSec, PPTP passthru. My VPN server is a NT 4.0 SP6. The VPN clients are win2k/98 machines.

I haven't been able to connect at all. I get an Event ID 721: Remote computer is not responding.

Does anyone have a similar setup? I need some help along the way. I'm pretty sure the clients and the Linksys are set up properly. Maybe the Cisco is blocking the PPTP requests? I've configured the NT's RAS without PPTP Filtering since there's only one LAN card. Are there any common pitfalls withthe configuration of NT's RAS?

Much thanks,

Herbert

9 replies

by craig haunch

The error is to do with certain ports being blocked, you need to go through the reports that the cisco creates when people are trying to connect as this should then tell you which ports to open.
I had this problem but used a firewall called winroute pro, this has logs that tell me what ports people were connecting on and then I opened these and got it working. Sorry but I don't know what they would be on a cisco router.

by stillatit

There is nothing unusual about the configuration you cited. We are using that and others.

First, if you are using NAT, turn off IPSEC -- it will not work to more than one station and takes special setup to even do that.

Your router must not block port 1723 or the "gre" protocol.

First test: From a client, can you ping the vpn server? You must have connectivity to the server. If you can't get past this step, find out why. It is a connectivity issue, not a vpn issue.

Second test: Are you using RAS or RRAS? If RAS, replace it with RRAS. You also need the PPTP protocol installed, and need to define some number of connections for both in and out.

Third test: On the server, set the requirements to any password and no encryption. Set a client similarly and try to connect. If they still cannot connect, look for a firewall at the server end filtering out port 1723.

Fourth test: Are all stations set up to use 128 bit encryption? If not, do so. Stations using 56-bit will not talk to stations using 128-bit.

Increase the security levels one step at a time until they are as high as they can go and still work. W2K may have some encryption issues with NT4.

Good luck.

by ann777

GRE operates through port 47, both UDP and TCP must be open.

I'm not sure about your dual configuration though. The fact that Linksys and Cisco are doing different things may be your problem.

I'd recommend that you try first with only theCisco in the loop (as it probably is the more configurable of the two). Once you have everything working than add the Linksys with DHCP, etc. As the other answerer recommended, you should probably turn off NAT from the LinkSys.

by ann777

Actually the second answer said to turn off IPSEC, not NAT. (I don't think you can turn off NAT on the Linksys -- that's one of the major features of their router).

by chanherb

A few clarifications:

I have set up the cisco to merely act as a bridge. There is no filtering enabled on it. The Linksys controls all the fitering. On the Linksys, I have port 1723 open to TCP, and port 47 open to TCP and UDP. IPSec pass through has been disabled, PPTP pass through has been enabled. From within the LAN, I can establish the VPN connection (looking for the server addressed at 192.168.x.x instead of using the WAN address). I also upgraded to RRAS but that didn't seem to help. Any other tips?

Herbert

This discussion is closed to new replies.