Discussion Locked

W98Setup GPF, DPMI, Corruption

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am trying to install Windows 98 on a formatted HD. (233mhz ? AMDK6 CPU, 32mg ram, 2 Gig HD) I keep getting errors at the copy files portion. Errors are:

W98Setup caused a general protection fault in module USER.exe at xxxxxxxx.

then after that at the black screen I get:

Standard Mode: Invalid DPMI return from 0367:5F92.

Then I tried installing Windows 95, did not work either, I get error msg:

Setup has detected a corrupt setup (.cab) file. This may be caused by a virus, low conventional memory, bad media or a HDW problem.

I removed all the cards and cables and reseated them. I swapped out the memory-from a computer that works fine, video card, Install CD, monitor, Hard Drive, removed the network card, Antivirus in the CMOS was already disabled. Still same problem!

Then I disabled the Internal Cache (I read a post which advised to disable the L2 cache but I have not been able to find it in the BIOS ? when it boots up it says L2 Cache = Pipeline Burst). The install then took several hours to complete but this worked overnight.

Now, after booting up ok, I get Blue Screens of Death!:

Ex: A fatal exception 0E has occurred at 0028:C000CC1B ? The current application will be terminated.

Each time I hit enter, the address changes until it finally goes black.

I just also replaced the battery. After booting I got

Error loading powerprof----, or corrupt file errors, then the BSOD w/fatal exceptions.

I also Loaded BIOS Setup defaults, sameproblems.

Please help??.

-KK

12 replies

by tbradley

Sounds like you have tried just about all the tricks, but after re-reading your post, two things come to mind. You say you get an error reading powerprof-----

This may be the power profiles in Bios. It could also very well be the heat/temp monitoring program built into some bios/motherboard systems.

I would suggest disabling both of these if present.

I have had trouble with some AMD processors in the past, and while reliable, maybe 1 out of 50 or so run HOT!!!!. As a last resort, try "underclocking" the CPU if the settings are available. IE, run your 233mhz as a 166 or 200 if you are able. If this allows you to get a good load, and start windows, then you know you have a "flaky" CPU.

From experience, I had a 200mhz that quit working period when I loaded Win95 the first time. Tried to load at least 40 times, with every combination of settings/hardware I could think of.

Reloaded Win3.1, and it's been working 7 days a week for the last 2 years without a hitch. Luckily I just happened to have a customer who didn't want to switch from 3.1.

by kck

Just a bit more info...

I attempted to copy the files from the CD to the HD to install from the HD. After the 2nd cab file it replaced the 'i' in win with an 'h' and said invalid ---. I tried again and got a little further but then junk appeared all over the screen, happy faces and such here and there and the computer froze. The computer was on for a while then.

I came back later when it was cold and tried the copy again and it copied all the files. Then I ran setup, and it locked up in scandisk, then again after that.

Power Mngmt is disabled in the BIOS. No Temp on this MB but I will definitely try to underclock the cpu!! Thank you very much...

-KCK

by mckaytech

Wow! I admire your persistence and attention to detail. The conclusion I would draw is that your motherboard has a defect in the memory management chipset. The only other thing I could suggest is to try running it for awhile in DOS - if it's a thermal or clocking problem with the CPU it will eventually fail where a chipset problem might never cause a problem with DOS.

The only other thing I can think of is that the CD drive might be defective - could you borrow another one to try?

paul

by tuqan

I agree with the above. Sounds like MB problems to me too. Having done all that you have said in your troubleshoot touched everything I could have suggested. However I do have a question. Did you remove the old partition before doing your format and give it a fresh partition? Or did you attempt to install windows on top of the old partition? If there was a problem with the old to begin with it becomes an inherited one if not removed prior to OS install. Simply formatting the drive will not fix a bad partition. Just a thought.

This discussion is closed to new replies.