Discussion Locked

Windows 2000 DNS Setup

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

When I setup ns1 in windows 2000 somehow I am missing something and the system does not
work. Can some tell me how to set this up?

7 replies

by fenaikh

Hi
plesae read this i have recived it from
Windows 2000 Server Tips at TechRepublic.com

INSTALLING DNS SERVER, PART 1
Since TCP/IP is a default network protocol for Windows 2000, DNS has
become the most important service for resolving names. In Windows NT
4.0, Microsoft used NetBIOS names, and thus the WINS was the default
mechanism for resolving computer names. That has changed in Windows
2000, where DNS is the primary name server and is required for Active
Directory. WINS can stillbe used for older clients, but it's no longer
required for a pure Windows 2000 network.

Before installing the DNS Server service on a Windows 2000 Server,
properly configure TCP/IP on the specific computer. That means you have
to configure theserver to use a static IP address (rather than a
dynamic address) and configure the proper hostname.

1. Go to Start | Settings and open the Network And Dial-Up Connections
folder.

2. Right-click Local Area Connection and click Properties.3. Select Internet Protocol (TCP/IP) and click the Properties button.

4. In the dialog box, select the Use The Following IP Address check box
and then type the IP address in the fields provided.

5. In the Preferred DNS Server field, type 127.0.0.1.

6. Click OK.

by fenaikh

Hi
plesae read this is the 2nd part i have recived it from
Windows 2000 Server Tips at TechRepublic.com

Today's Windows 2000 Server tip

INSTALLING DNS SERVER, PART 2
You'll be relieved to discover that installing DNS Server service is
quite straightforward and is done the same way that other Windows 2000
components are installed. The DNS Server service can be installed
during the Windows 2000 Server installation process or after.

Once Windows 2000 Server has been installed, follow these steps to
install the DNS Server service:

1. Go to Start | Settings | Control Panel.

2. Double-click Add/Remove Programs and then double-click Add/Remove
Windows Components.

3. In the Windows Components Wizard dialog box, select Networking
Services and click the Details button.

4. In the Networking Services dialog box, select DNS and click OK.
(Make sure you check the box before DNS and not just DNS.)

5. Click Next.

6. When you're prompted for the Windows2000 CD, insert it and click
OK.

7. After Windows 2000 finishes copying files, the installation is
complete. (It's not necessary to restart the computer.)

Unfortunately, your clients cannot start using the DNS service right
away. The service installation is only one part of your job. Before
your clients can really start using the DNS service, you have to
configure the service and create some DNS zones. That will be covered
in the final part of our series on installing the DNS Server service.

good luck

Mohamed

by fenaikh

hi again pls look at these article and white paper from Microsoft.
Good luck
Mohamed

Article ID: Q237675
Setting Up the Domain Name System for Active Directory
http://support.microsoft.com/support/kb/articles/Q237/6/75.ASP
URL:
Article ID:Q255134
Installing Dynamic Host Configuration Protocol
(DHCP) and Domain Name System (DNS) on a Domain Controller
URL:
http://support.microsoft.com/support/kb/articles/Q255/1/34.ASP

Windows 2000 DNS White Paper
URL:
http://www.microsoft.com/windows2000/library/howitworks/communications/nameadrmgmt/w2kdns.asp

Note:
pls always watch for spaces in URl's
Good luck
Mohamed

by fenaikh

Hi
Chapter 6 - Windows 2000 DNS
wwww.microsoft.com/technet/win2000/win2ksrv/reskit/tcpch06.asp
plesae read this is the 2nd part i have recived it from
Windows 2000 Server Tips at TechRepublic.com
DNS ALIASES, PART 1
Domain Name System (DNS) can be described as a service that maps host
names (i.e., computer, domain, etc.) into IP addresses. However, this
basic definition doesn't allude to all that DNS can really do.
One of the features that is used by almost all Web servers is aliases,
which represents another name for an existing entity. For example, if
you have a computer named computer1, you can create an alias for it and
call it mycomputer.
This concept is widely used on the Internet. When you type
www.techrepublic.com in your browser, you're requesting a service from
a computer named www in a techrepublic.com domain. When system
administrators install the operating system, they don't name it www.
Instead, they often use a name that doesn't represent any kind of
service.
When a service is installed, such as a Web service or FTP service, they
add an alias for this machine. For example, system administrators might
make www the alias for Web server and ftp the alias for FTP server.
This allows users to contact the service by its name. So when you type
the address of the Web server, the DNS resolves this name. Then DNS
recognizes that this is an alias, finds the original host name, and
gets its IP address.
In part two of our series, we'll explain how to create a DNS alias in
five simple steps.

by fenaikh

Hi
this is the second part of DNS ALIASES
from :Windows 2000 Server Tips at TechRepublic.com
goo luck
Mohamed
DNS ALIASES, PART 2
In part one of this series, we described the Domain Name System (DNS).
Now it's time to create aliases in Microsoft's DNS service:

1. Open the DNS console from the Administrative Tools folder.

2. Expand the forward lookup zone and the domain in which you want to
add an alias.

3. Right-click in the right pane and select New Alias.

4. When the New Resource Record dialog box appears, type the alias
(e.g., www) in the first edit box. Type the fully qualified domain name
of an existing host for which you are defining this alias. You can also
click the Browse button if you want to select it and not type it
manually.

5. Click OK.

If you look at the DNS console, you can see that the Type column for
this new alias displays an Alias That Data column, which shows the
fully qualified domain name of an existing host. You could say thatan
Alias maps a second name to the original host name.

Now when you look at the original host name, you can see a Host Under
Type column and the IP address of a host in the Data column. This is
the most-used DNS feature--mapping a host name toan IP address.

------------------------------------------

This discussion is closed to new replies.