Question Locked

Windows will not recognize my hard drive

0 helpful
25 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I had to reinstall Windows XP. Windows will now not recognize my slave hard drive. BIOS sees it and I can see it in the hardware list but I can not access it. Any suggestions?

25 replies

by michael jay

on My Computer, select Manage and then disk management. Does the drive show there?

by sparaxis1

It does not show there. It was there until I reinstalled Windows. I haven't changed anything else.

by michael jay

that it shows in the BIOS and in the hardware list, by hardware list do you mean Device Manager in Computer Management?

by canvasshoes2

I don't know if this helped the Original Poster, but I had the same problem, and this was just the ticket to fix it! Thank you, thank you!!!

Laura

by holyseraph2001

I had the same problem with a seagate 1TB SATA drive, originally it is not recognized by the windows system. The trick is that new hard drives came un-formatted, so you need to go to my computer--> manage --> Storage, then at the storage management screen, initialize the drive and creat a new partition with it.

by w4clm

Thank you, I also had the same problem as it appears many are having installing a second SATA drive. One in Manage --> Storage the drive was located quickly partitioned and formatted. Total of 931.51 GB (1 TB ) Western Digital SATA drive now installed up and running thanks to your posting of 9/20/08
CLM

by w4clm

Thank you for this posting. Once in Manage -- Storage, the drive was easily identified, partitioned and (Right Click) to format. Now formatting at 931.51 Gb (1 TB) Western Digital SATA drive.
Thanks again and regards
CLM
Technician

by fupa

this solution fixed my problem exactly. i was have the same problem as the OP and this is exactly what i needed to do. thanks very much.

by big_herpes

So, I had this problem too, and some of the suggestions led me down the right path. Right click MY COMPUTER and click on MANAGE. Click on STORAGE, then click on I think DISK MANAGEMENT. In there, towards the bottom you'll see the first hard drive that says (system). Underneath it I had a HDD that said Disk 1, Foreign. Right click on it, and it will give you an option to IMPORT FOREIGN DISKS. That's what I did, and it worked out perfectly. Hope this helped.

by sparaxis1

The drive is listed in the device manager. When I right click on it, Windows even says that it is working properly. I have tried to update the driver and Windows says that the driver is up to date.

by michael jay

The only other thing that I can think of is jumpers, but if it worked before it should work now.

Master drive has master jumper, slave drive has slave jumper? Check that.

If you have access to another computer I might suggest that you slave that drive to it and see if it works there.

Anyone else looking in, what have we missed?

by dma69593

I'm the same as you. If there is only one hard drive installed, it should be set as the master drive and cdrom drive as secondary. Two hard drives requires one set as master and one set as slave. Is this person trying to install XP on slave drive, because it won't work.

by michael jay

Uninstall the drive in device manager, then scan for hardware changes. This should reinstall the hard drive, it is a long shot but this may bring the drive back to reality.

by clivefpowell

So I look forward to seeing what your solution turns out to be. I have already done most of what has been suggested, so tonight it is unplug, switch on, switch of and replug hard drive. If that doesn't work transfer it back to the old PC.

by clivefpowell

Well unplugging, booting and then switching off and replugging it all in didn't work so this week end is putting it back into the PC it came from.

by clivefpowell

Could Sparaxis try using Belarc to see if that can also see his drive? It can mine. I get

Generic USB CF Reader USB Device [Hard drive] -- drive 3

Generic USB MS Reader USB Device [Hard drive] -- drive 5

Generic USB SD Reader USB Device [Hard drive] -- drive 2

Generic USB SM Reader USB Device [Hard drive] -- drive 4

SAMSUNG SP1604N [Hard drive] (160.04 GB) -- drive 0, s/n S013J10Y645773, rev TM100-24, SMART Status: Healthy

WDC WD400AB-00BPA1 [Hard drive] (40.02 GB) -- drive 1, s/n WD-WMA6R2904473, rev 18.20D18, SMART Status: Healthy

So why can Belarc see it but nothing else?

by jaysettle

bios and disk management sees my 200Gb hd but My
Computer doesn't---so in disk management I right clicked
on 200Gb hd and went to convert to dynamic disk and went
through the instructions to finally format it. It has appeared
now in top window in disk managaer under the C: drive and
is now up to 8% formated-hope this works. (Fortunately I
didn't have any important info or data on the 200gb hd so
was able to click the format option)

by heymoa

i am having the same prolem with a SATA drive. the PC has 2 IDE hard drives one master and one slave that are working fine but the master is full and i want to clone it to a new 250gig SATA drive.

the drive shows up in the bios but windows will not recognise it in disk management even though it shows up in the device manager. also partition magic recognises the drive but i couldn't use that to format the drive as i only have the demo version. i plugged the drive into a different PC and windows found it straight away and the balloon for new hardware popped up. so what is this other PC missing?

by peter42y

Same problem.
Windows 98 able to see both drives. After I installed XP drive D dissapeared from the windows explorer tree but computer managment does recognize it. It has no letter assigned.

by arsenyc

I also reinstalled Windows XP becauses of some missing files. I had two working hard drives installed before the reinstallation. But now, only the primary drive shows. My problem is that the drive appears in the BIOS, but does not appear in disk management of explorer. I rechecked the BIOS 4 times and everything is the same as it was before, and I didn't touch the inside of the computer. I just can't get it to show up in disk managment. Please Help!

by burke91

my secondary hard drive (d:) must have had a loose connection. opened the case and adjusted the connectors but now it isn't recognized windows (although it is seen in bios, device mangager and partition manager). when i disable and reneable the drive in device manager it then becomes visable in windows, but only until my next reboot, then i have to go through the whole disable reenable procedure again....

any ideas???

thanks..

dan

by jamonbaldwin

My computer will not recognize my maxtor slave hard disk. It is not listed under disk management either. It is enabled in my bios. When I try to detect it in my device manager it says its not properly connected to my computer- "code 45". Well, I've reconnected all my wires 5 times at least, my jumpers are set to slave. Please help.

by dannyjack007

Checked Management and there it was. Formatted and ready to go. Thanks a bunch!!!

This discussion is closed to new replies.