Discussion Locked

WINNT 40 MODEM INSTALLATION

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Good Morning Gurus.Last Friday Passed my NT
Server Enterprise test.I have two more to go,
TCP/IP & IIS.I am a self study person.Gain tremendous knowledge from This site.Although I am reluctant to post this Question(A little embarrased by the lenght of my troubles)Simply ran out of options,So here we go.Since the beginning of my studies,I am having a horendous time installing modems on my nt40 server.Told on read me file to run setup from a: which i did,after reboot service error could not open com3.removed modem added com3, assigned i/o 3e8,looked in winmsd irq 7(available),reinstalled modem with same error.On a few occasions notified
me required dll's are not installed.It may be
a routine for all other folks,am getting the
feeling Ineed help .Any thoughts will be very welcome & appreciated,THANX-AZIZ

8 replies

by ulf

Add the modem from the modem-applet in controlpanel. Change the driver to the manufacturer's.
If you are having trouble with the com-ports.
In the ports-applet: remove all ports and reboot. And then add the modem.

by dkpalmer

You don't mention what type of modem you are installing ( is it PCI? ), so a little hard to troubleshoot. But here are some thoughts.

Note: IRQ 7 is the default for LPT1 - it's almost certainly assigned in the BIOS and not available.

Best bet is COM3 using either IRQ3 ( the normal default ), or IRQ5 ( as long as your network or sound card aren't using it ).

by azizhakim

I just bought this us robotics 56k pci modem
last Saturday,I did have a pctel that came with my pc,since i had so much trouble trying to install,i just threw it away in frustration.my other nt server40 box has a serial mouse,i did not have any trouble installing,it sent it to com1 where it is,happy.NB. I HAVE NOT TRIED IT ON IRQ 3.MY A+ BOOK TELLS ME COM1&3 TAKE IRQ4, COM2&4 TAKE IRQ3.I WILL DEFINITELY TRY IT ON IRQ3
ON COM3 AS YOU SUGGEST,Every time i assign the a+ book values,i get those errors-THANX

by shanghai sam

Don't know how much my answer will help, but here goes... If it will make you feel any better, a lot of people have probs with NT and internal modems especially the so-called WinModems. And US SchlockBotics modems SUCK!

I too have used PCtel(win)modem in a NT box, tried adding com ports they way you have and no luck. What I ended up doing was to go into the system BIOS and disable Com/Serial port#2, my mouse is on Com1. Then ran setup from the NT drivers folder on the CD that came with my modem.

That action not only installed that drivers but it also setup the modem to use Com1 and it works. Yes the mouse is plugged into that physical port, but the modem is apparently using a virtual port.

You can goto www.pctel.com to locate current driver versions.

Your A+ book is giving you the correct IRQ's and addresses, however keep in mind that those are for external modems or internal modems that are "controller" based. Controller based internal modems usually (but not always) have jumpers for hardware selecting IRQ and address values. Others use a configuration program to set those values. Like the way soundBlaster sounds are setup.

If you really want to solve your problems permanently, spend a $100 on an external Diamond SupraExpress external and be done with it. If you do, be sure to leave Com2 enabled and set to 2F8 in the system BIOS.

Once you've had an external modem, you'll never go back to an internal. Bin there done that, speaking from experience.

Good Luck

by azizhakim

Thanx.Input helped,although i still am unable to finish.I will heed your Advise & go with Xternal modem,once again,Thanx

This discussion is closed to new replies.