Discussion Locked

copy MASTER DRIVE TO SLAVE DRIVE

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
How do i TRANFER THE ENTIRE DRIVE C: IN WINDOWS 2000 OR WINDOWS XP, TO A SLAVE DRIVE D:. BECAUSE MY DRIVE C: IS ALMOST FILLED, UP AND MAKE MY SLAVE DRIVE D: THE BOOTABLE DRIVE C:.

13 replies

by wcp

You need to use a third party software like Norton Ghost or PowwerQuest Drive Image.

You may also use DOS command XCOPY from Command prompt. To do that, you have to physically connect the two hard drives to a third computer with Windows 2000 or XP. I have done this before and it WORKS.

Please post a comment if you need more information on how to use XCOPY.

by wcp

After you transferred files, make sure you change the hard drive jumper settings.

by wcp

As long as the HD stays in the same computer, you do not have to worry about SID.

The reason to use XCOPY from Command prompt is to use appropriate keys to override some restrictions that prevent dragging and dropping to work in Windows Explorer.

First of all, the new HD must be partitioned, formatted (NTFS), and set as active to make it bootable.

I will post more info.

by wcp

A while ago, I posted a question in TechRepublic regarding to using XCOPY to ghost C: drive in Windows 2K or XP.

I have used XCOPY in Windows 98 and ME successfully (sometimes it is the only way to ghost the C: drive) but I quickly found out it did not work in Windows 2K or XP. The main reason is that while in Windows (2K or XP), some files (Default, SAM, Security, Software, and System in C:\Windows (or Winnt)\System32\Config) cannot be copied. Without theses files, Windows cannot be loaded.
After about three months without getting any solution I closed the question.

I finally found one from my trial and error, help from Microsoft, and from Microsoft Knowledge Base.

The following are the steps I took.
Let?s say C is the hard drive (HD) I want to ghost to D which is new and bigger in size.

1. Boot to Windows (2K or XP)
2. Navigate to Disk Management to initialize (Basic), partition (Primary), format (NTFS), and make the partition of the D drive as active so it becomes bootable.
3. Shutdown the computer.
4. Disconnect the two HDs and connect them to a different computer with Windows 2K or XP in NTFS. Boot the computer. Let?s say the C and D above is now D and E, respectively.
5. Navigate to Command Prompt.
6. Type ?XCOPY D:*.* /s/h/e/c/k/y/r E:? without the quotes and press Enter key. Copying process starts.
7. Type ?Exit? without the quotes when it is done and press Enter key.
8. Shutdown the computer.
9. Disconnect the HDs.
10. Change the jumper setting so the bigger HD becomes C:
11. Connect the HD to the original computer.
12. Boot the computer with a Windows 98 Startup disk.
13. From A Prompt, type ?Fdisk /MBR? without the quotes and press Enter key.
14. Take out the floppy and reboot the computer.
15. You should be in Windows 2K or XP exactly as before but with bigger HD size.

by wcp

Unlike in Windows 98 or ME, I have not been able to figure out ghosting a HD to a directory of a different HD.

Please post a comment if you have any question or need help.

by wcp

The above should have been "ghosting Windows 2K or XP HD" not "ghosting HD".

by curacao_dejavu

That is not possible the way you want it, You will need to make the d-drive bootable and that can not be done with copy files.

I see 2 solutions:
a: install xp or w2k, when installing select the d-drive to install the os on. then install the applications that you need, and then copy ONLY the data files (like *.doc, *.xls etc ) on a new data folder on the d-drive. After that proces you can delete the folder on c-drive (only folder because you need like 4 files on the c-drive to tell the os that the system partition is on the d-drive.

b)
Assuming d-drive is empty,
physically swap the d and c drive, in your machine.
then install w2k or xp, install the applications that you want.
copy the files from the ex-c now d-drive to the new c-drive.
format d-drive to have a empty partition.

Of course if you have a cd burner, I would burn all data first on the cd. Then install w2k or xp and format everything in the process.

Leopold

by dmiles

Create boot disk

Set both drives to Master and set CD-ROM to slave

Mount both drives in cabinet (choose location that allows cables to be swapped)

Connect new drive to primary IDE channel (do not connect old drive or CD-ROM yet)

Boot from the floppy that you created in step one and Fdisk the new hard drive with or without partitions (depends on which version of windows)

Format with /s option (format c: /s) and format additional partitions if necessary.

Boot from hard drive to confirm format.

Power down.

Disconnect primary data cable from new drive

Connect primary data cable to OLD hard drive and secondary data cable to new hard drive (no need to connect CD-ROM yet)

Boot up, you should end up back in windows

Go to MyComputer you should see the new hard drive as D:

Check that there are only system files on drive D:

From MyComputer's command bar click on (View) make sure show all files is ON and hide system files is NOT checked.

Press CTRL+ALT + DEL and end all tasks except Explorer and Systray

Open MyComputer and DblClick on drive C: then open MyComputer again and DblClick on drive D: this will give you two windows one drive C: and one drive D:

Position the windows so you can see the files on both drives, click on the drive C: window, make sure that you are in the ROOT folder. Select all files except Win386.swp. RightClick drag selected files to the drive D: window and select copy.

Go have a cup of coffee or soda

After files have copied power down and remove data cables from both drives.

Connect primary data cable to new hard drive. (do not connect old drive or CD)

Boot up and if everything went ok you should have a copy of windows with all your installed apps on your new drive.

by carlos0463

I am not sure, but I believe i read somewhere that you cannot just copy files over with Windows 2k/xp and try to boot. I believe the HAL, SID and/or hard drive have to be the same in order to boot.
I believe I read this in the SYSPREP page from ms. But, I could be wrong, if anybody is knowledgeable of sysprep it would be cool :)

by voldar

To do that is very simple - use Drive Image 4.0 (Pro) from Power Quest - it is a very simple to use program.

by pc girl

You need either Partition Magic or Ghost. Ghost is by symantec which is included with norton system works 2002 or I believe it can be purchased seperatly. All you really need off the Ghost software is the boot floppy you create from the Ghost software itself. That boot floppy can then be used to do mirroring and manipulations on any pc and you don't even need the software anymore. Depending on which software you choose, things will go a little different. In think I would recommend Ghost in your case since you want to ultimatly boot from drive D. For everything else but this, I use Partition Magic. Now, be careful to read exactly what your doing so you don't copy D to C instead of C to D. When it's complete, it will ask you if you want to hide the second drive so not to cause problems upon reboot. You want to say "NO" do not hide drive. I've never had any problems and it's a pain to un-hide it later. Reboot, verify the copy was sucessful, shut down, change the jumpers on the hard drives to fit your hardware setup and then go into the bios to verify it reconizes both HD's and that it's set to boot from the one you want.
If your not familiar with jumpers on hard drives, IDE connections on a motherboard and how to configure primary master versus secondary master ect... Then i recommend you learn it first or call in the calvary. Unless you have a lot of time, I'll keep checking back.

One more thing, make sure you have enough room on C drive to install the Ghost software.

Good luck.

by dbtrend

If you plan to image Win2k/XP for use on the same system, you can use several different Drive Image programs such as Norton Ghost or PowerQuest Drive Image. These programs will duplicate the system exactly, but if the system is part of a NT/2K Domain, you must use the Sysprep tool which is part of the MS Deploy tools on the CD ROM.
The Sysprep tool removes the SID from the system so that it can be imaged. A new SID will be generated the first time the system is booted.
Note that because the SID is removed from the host machine you should not use this system for use on the network after running Sysprep.
If your machine is a member of a domain, and you do not run sysprep before imaging the drive, the system will not join the domain when it starts up, and you will need to remove the system from the domain and add it back again.
This is not a big deal, but saves time if you run sysprep first.

If you plan to use the image in a different system you should use Syspart tool.
The difference between the two is that Syspart copies the OS files to a second Hard disk, but will not add the hardware drivers. When you boot the drive that has the new image, it will automatically redetect all of the new hardware drivers and generate a new SID. It will also run a mini setup wizard to obtain the new machine information, (name, Network settings,admin password etc..)
The syspart tool must have a second hard disk attached to the system locally to use it, but does not use third party tools for imaging.
I am not sure if the Syspart tool will copy all of your data to the new drive, so make sure you have a good backup of your data first.

This discussion is closed to new replies.