do I have a virus
my windows clock loses time if I re boot it is right when it loses time I get hang ups and mouse pointer freezes
I can not run windows disk defragmentation on drive c a fixed hard disk but I can on drive d another fixed hard disk
Windows Forum
my windows clock loses time if I re boot it is right when it loses time I get hang ups and mouse pointer freezes
I can not run windows disk defragmentation on drive c a fixed hard disk but I can on drive d another fixed hard disk
by oz_media
Sounds like you've got a lot going on and maybe not enough RAM to do it.
You may have a bad CMOS battery, but that usually just goes and doesn't slow.
What OS are you using? Other specs,i.e. RAM, processor type and speed etc. would be helpful.
by fred07
hi,
First sign of a cmos battery failure is the clock will not keep correct time.
Clock will change time every boot up.
Change cmos battery now and your problems will probably go away.
When doing disk defrag on a problem drive do so in SAFE MODE.
That should solve that problem.
fred
by 1stladytech
I would also check for spyware, it sounds like you have to many processes running at the desktop. Since the clock is correct after a boot, I would not suspect the CMOS battery. Download SpyBot's Search and Destroy at www.download.com and make sure to update it before you run it. If that doesn't fix the time problem, try shutting off programs in msconfig until you find the one that is not allowing your clock to update properly.
Vickie
by techkid
by techkid
by sgt_shultz
by stuart_at_oz
First things first - do you have anti virus software installed on you PC, and is it up to date? Using the internet with out one is like bungee jumping with out the rope. :-)
I have seen similar system/mouse freezes with faulty CDROM drives..... (yes, seriously)
We have had problems with one manufacturer/speed only - the Mitsubishi Diamond Data 48x cdrom drives (over 50 at last count). Other speed drives from the same manufacturer are fine.
They have displayed various symptoms, including system freezes, sometimes the trays pop out and in for no reason, and even a couple of hard drive corruptions. All have been fixed by replacing the CDROM!
It may be worth disconnecting your CDROM drive and trying it, see if it helps.
If you have a 48x Diamond Data CDROM I would put money on it being the cause.
Having said that, it is also worth doing the points mentioned above, especially checking for spyware (I use Lavasoft's Ad-Aware) and doing a scandisk and defrag under SAFE mode.
I would also recommend using a firewall such as the one built into WinXP, or for older Windows versions, try Zone Alarm (www.zonealarm.com)
You should also state upfront what version of Windows you have, and the general spec's of your computer, so the people trying to help can be more specific with advice.
Hope this helps,
Stu
by stuart_at_oz
by keiko105
by nzholden
Is it overclocked? also some software that tries to set it to some other time zone ( naviscope etc).
Hard to say about your problem at this stage. It could even be faulty motherboard with broken tracks or a loose PCI card ( ISA has thicker strips) . Try reinstalling windows. if the problem i am trying to solve takes more than 30 minutes i save my files and resinstall and I am pleased from the results till now.
by rcom
This was an problem caused by McAfee virus scan. The issue is fixed with the 4160 scanning engine.
ftp://ftp.nai.com/pub/antivirus/engine/4.x/elnx4160.zip
by whopi
You were very short explaining your problem. (is this a recent PC, with W98 ou W2000 ou XP). Normally, a lithium CR2032 battery must have 3 Volts. Remove the battery and ask around for a voltmeter: buy a new one when voltage goes below 3 Volts.
A low battery cause a loss of time reference from boot to boot, but also the loss of hard disk configuration and boot sequence preferences, it seems it is not the case. I have seen defective clock chips with little or annoying time shifts. In that case, there is not other solution than to discard the motherboard. I hope that you have a recent one, and not an Olivetti M24 with a clock ending up on dec 31, 1988!
To succed with the defragmentation, you need tho have a clean bootup and no blocking processes of processes using periodically the hard disk. A first solution is to stop the processes from the processlist accessable after a single CTRL-ALT-DEL.
The second way the perform a Defrag without interruption is to start up the Windows in SAFE MODE (pressing F8 during the bootup sequence and selecting SAFE MODE inthe list.
by mrmyke
This discussion is closed to new replies.
Sort by Trending