Discussion Locked

How to install dual O/S - ME & XP?

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I want to install dual O/S on my computer. I currently have ME, and want to install XP as well. I tried to do this a few months ago - created a new partition on my C drive, and tried to install XP onto that, but when I did that, it messed up ME sobadly, I had to reformat. I gave up with XP and just reinstalled ME, because a lot of my hardware won't run under XP. Can anyone tell me step-by-step (ie "dumbed-down") instructions on how to successfully install XP while keeping ME? I know a screen comes up for you to pick which O/S you want to go into; I want the computer to automatically boot up ME as the default. HELP, PLEASE!!!!!!!!

Thanks!
Jen, the Jersey Girl

8 replies

by thechas

If you still have the same hardware that you had the last time, you are still going to have problems with XP!!!

I recommend that you start by going to www.pcpitstop.com and running the XP Readiness Test.

http://www.pcpitstop.com/xpready/default.asp

Post the results back here, and we can help you update your PC so that XP can run properly.

As far as installing XP, it sounds like you know what to do, you just don't have the correct hardware for it to work.

Anyway:

Boot up into Me.

Have the extra partition ready.

Insert the XP CD.

Follow the prompts to install XP in a dual boot setup.

Make sure that you direct XP to install on the new logical drive (D:?)

Install XP updates when done.

To make Me the default operating system, run the bootcfg command from the run box in XP.

From the XP help menu:
"bootcfg default"
Specifies the operating system entry to designate as the default.

Syntax
bootcfg /default [/s Computer [/u Domain\User /p Password]] [/id OSEntryLineNum]

Parameters
/s Computer
Specifies the name or IP address of a remote computer (do not use backslashes). The default is the local computer.
/u Domain\User
Runs the command with the account permissions of the user specifiedby User or Domain\User. The default is the permissions of the current logged on user on the computer issuing the command.
/p Password
Specifies the password of the user account that is specified in the /u parameter.
/id OSEntryLineNum
Specifies the operating system entry line number in the [operating systems] section of the Boot.ini file to designate as default. The first line after the [operating systems] section header is 1.
/?
Displays help at the command prompt.
Examples
The following examples show how you can use the bootcfg /default command:

bootcfg /default /id 2
bootcfg /default /s srvmain /u maindom\hiropln /p p@ssW23 /id 2

Chas

by estreetjerseygirl

Thanks! Since I've had so much bad experience in the past trying to install XP, I figured it'd be best to get step-by-step directions so I was sure not to f*** it up!

by estreetjerseygirl

Just FYI, both my parents have worked for IBM since before I was born. I've been typing since I was 3, on the internet since I was 7. I'm 23 now, if you must know. So don't insult my intelligence by telling me to "take a basic computer lesson," asshole. What, did your mommy take away your Crayolas, so you have nothing better to do than post asinine comments like that?

by sbennetsen

I would first install a second hard drive. XP runs best on a NTFS (NT file system) which 98/ME can't see. When you boot from (XP) it will see your ME partition. Cheap an dirty is to buy system commander. Makes booting from different OS a snap (painin the butt to remove though!

This discussion is closed to new replies.