Discussion Locked

Installing a Network Card

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have installed a Linksys LNE100TX Fast Ethernet Adapter and when I boot up I get Error Resource Conflict PCI Network Controller Bus:00 Device:0E Function:00 Press ESC to resume. How do I fix this?

19 replies

by lathe

Your problem is your IRQ (Interrupt Request) is conflicting with anather device, if you are using Win 95/98 go to mycomputer on desktop and click right mouse button and properties. Click on device manager, look for network adapters, you will be getting a yellow or red mark on the network card click on the card and click on the properties in that go to resources and remove the check mark on use automatic setting and go to change settings, then you will see interrupt request and you will see a number in in the settings field, change the no. to a different one like 10 or 11 or so, look in the bottom box for IRQ conflickt if it is showing any confilict change the no to a different one till it shows no conflict and restart the system, then you have to install the required drivers.

All the best

by mckaytech

You didn't tell us about your motherboard but I've seen this problem with some AGP motherboards that share some resources between the AGP video card slot and the PCI slot right next to it. In that case, the solution is to move the network card to another slot.

If that doesn't work, you'll want to go into the CMOS setup and take a good look around. The error you report is coming from the BIOS, not the operating system, so the problem has to be either in the CMOS setup or the card itself.Hope this gets you started - if not, if you can re-post with the motherboard make and model and what OS you're trying to run, it will be easier to provide a good answer.

paul

by james_randy

Ive seen cases similar to this with LinkSys cards that were installed with the wrong driver. Even if you used the driver that came with the card, it could be the wrong one. Go to the LinkSys web site and download the correct driver. They know that this problem occurs, and they have a page with pictures of cards, chips, etc., so it's easy to find the right one. See link: http://www.linksys.com/download/default.asp (I got tired of screwing around with the LinkSys driver hassles, and went back tobuying 3Com.)

by tlippert

This appears to be a problem in the bios. The problem is i am not too familiar with AMI bios's. In the PCI configuration data there is a place to set the IRQ and IO information for PCI slots. I have only seen this with an AMI bios. It may take a couple tries. Good Luck

by elai888

I have the same exact problem you have. I've tried two Linksys Ethernet Adapter, and both didn't work. So, I bought a 3COM, paid $40 extra, and it worked instantly.

by brgraves

In order to answer, it will be helpful to know OS, whether or not the NIC is PCI or ISA. How many PCI/ISA slots are filled?
If running W98SE what does System Info indicate? At any rate, it seems as an IRQ conflict. Is the BIOS setup as a PNP OS or not. Is the device capable of PNP or must it be assigned resources. More info will result in direct answers rather than questons

by mjohnson

I've installed these cards in a few computers, with no problems. As one person mentioned, is the motherboard AGP? From your details, "Controller Bus:00" I'm guessing that it in the top most slot (slot 0). This is generally close to the AGP port.

Have you tried to move the card to another PCI slot? Make sure you have the latest drivers. Also, try the card in another PC or try a known working card in this particular PC.

I've never had problems with Linksys cards, but there have been a couple cases with Netgear cards where I had two bad cards in a row. It happens from time to time.

Good luck!

by jeff kraft

I'm going to assume that the network card is in PCI slot 1 next to the AGP video card. Try moving the card to a different PCI slot. If that doesn't cure the bootup problem, remove as much of the hard ware as possible (sound card/modem) and boot up. Add each piece of hard ware one at a time until you find the culprit(s).

by 9878445

I agree with paul in answer 2 I believe it was the error message is comming from your bios I have seen resource conflicts from bios on modems. I have never seen a network card conflict with a setting in the bios but it is entirely possible. I would check the bios maybe reset the default config and reset the ecsd data and if nothing else move the card around to a different pci slot. I have also seen motherboards that have problems with that first pci slot thats right next to an agp slot.

This discussion is closed to new replies.