Discussion Locked

Installing win95

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

New tech.Have a laptop with 194mb hd and 386 enhance cpu.Formatted with fat16.when insert the '95installation cd in the drive and enter the command "autorun" it says this programm can not run in ms-dos mode.I have search the whole cd for setup.exe file.But could not find the file.Like a stupid try to run setup.exe from dos command line.
The answer "bad command or file".Please help me out.I know there are a lot of tech with the answer,because to them it is very simple.Thanks in advance. Babul.

14 replies

by dmiles

SYMPTOMS
When you restart your computer in MS-DOS mode, restart to a Windows command prompt or restart your computer and use a startup disk, you may not be able to access your CD-ROM drive. This behavior may occur even though you are able to accessthe CD-ROM drive from the Windows graphical user interface.
CAUSE
This behavior can occur if any of the following conditions exist:
The CD-ROM driver or Mscdex.exe file is disabled (commented) or missing from the Autoexec.bat or Config.sys file.
The CD-ROM driver or Mscdex.exe file is missing or damaged.
The startup disk does not contain the CD-ROM driver or Mscdex.exe file.
You have replaced the original CD-ROM and not updated MS-DOS drivers.
To access a CD-ROM drive when you bootto a Windows command prompt or restart the computer in MS-DOS mode, you must load the real-mode CD-ROM driver in the Config.sys file and the MSCDEX driver in the Autoexec.bat or Dosstart.bat file. If your CD-ROM drive is supported in protected mode in Windows, the real-mode CD-ROM and MSCDEX drivers are most likely not being loaded in the Config.sys and Autoexec.bat or Dosstart.bat files on the hard disk. In addition, if you boot from a floppy disk, the CD-ROM and MSCDEX drivers will not load unless you manually configure the Config.sys and Autoexec.bat files on the floppy disk to load them.
RESOLUTION
To resolve this behavior, use any of the following methods:
Run the Dosstart.bat file.
Extract the correct version of the Mscdex.exefile.
Add the appropriate files and commands to your startup disk.
Install the MS-DOS drivers for your CD-ROM from Command Prompt Only

by thechas

Yes, you cannot run the W95 installer from true DOS.

You need to boot from a W95 startup disk.
Unless you have the upgrade from Windows 3.1 version of 95.

You either need to copy a W95 startup disk, or download an image.

2 sources are:
www.bootdisk.com
www.madboot.com

Extract the image, and copy it onto a bootable floppy.

If the laptop does not support having both the CD and floppy drives in place, boot from the floppy, and run the system command (sys C:) then copy the floppy files onto the hard drive.

Chas

by maelgwyn

Ok, on the DIR structure of Win95 there is a dir
called \win95.

If you go to that dir and then type setup, you
will get the install. Now, if you have problems,
try copying all the files to the HDD (the ones
on WIN95)

You can run the install form any vrson of dos,
since it is is only dpendant on having a couple
of files running.

Anywho, it probably is no help, but, send me
an email if you need more help.

Mael

by zlitocook

It's been awhile but get a win98 boot disk, with fdisk, format on it. You can borrow it down load it, or go to a 98 computer and make one from add remove programs. Boot to it and type (format c: /s /u and answer yes. After it's done reboot and type in the letter it give's for the CDROM, like if your computer shows a A: prompt type in the letter it gave your CDROM d: then type setup. And follow the directions.

by fred07

Anyone may correct me but I do believe you have insufficient HD megs for win 95. Scratch my head for size of HD for win 95 and you will not get any thing over 95. I do believe you have a DOS or no more than win 3.1 that can go on that machine.

by cpb72

Infact, I should mention that all the suggestion I have received, was performed by me even before I submitted the question. I have access to the cd rom.I booted using a 95 bootdisk which was edited.
When the machine boots from bootdisk,it loads thediagonostics tools in drive D and assign a letter E for cdrom.I insert the 95 cd into the cdrom and change the drive from A to E.Then I cd to win95 and enter the command setup.exe. I get the following messages"bad commnd or file" then I explore the cd and found no setup folder.I tried to cd to autorun and run the autorun.exe. It says
this programm can not run under dos mode.Again the machine has no windows installed.Could the setup.exe be some where else in the disk? If anyone want to write me personally,please do so. Below is my e-mail.cpb72@aol.com

by tg2

check to see if your setup.exe is acatually oemsetup.exe

and the other post I think is right also... you may not have enough space on the hard disk for a win95 install, although that's not causing your error at this point.

:)

This discussion is closed to new replies.