Question Locked

Laptop shuts off with batt in, but runs fine on AC power

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I recently acquired a Gateway MX6625 laptop that was non-functional. I replaced the motherboard because the old one had been zapped (I suspect it was because the power connectors' soldering on the board was burned) and the laptop wouldn't turn on or anything...no lights, etc. Anyway, I replaced the board and it boots up fine now. I purchased a new battery for this unit as well, because if it had been zapped, I didn't want to use a bad batt. When I put the new batt in, the laptop will start to boot into Windows and then will just shut off. If I remove the battery, the laptop will run no problem. When I have the unit off and I just plug it in to see if the batt will charge, the purple light (charging light) comes on for about a minute and then will go out. Then it will come back on about 20 seconds later and then go out after a minute and back and forth it goes. The batt never gets a charge.

So to recap, I have a new mobo, new batt, it works fine on AC power alone, but not with the batt in. I have to take the batt out and just use AC power. I have also tried a different AC adapter (same volts, amps, etc.) for fun and it does the same thing.

Any suggestions?

9 replies

by oh smeg

By the sounds of things it may even be a shot Mains Adaptor so check that first to see if you are getting the right voltage and Current.

It sounds as if the Battery is pulling the DC Rail down to a level where the system will no longer work or it's drawing more power than the M'Board/Power Supply can offer. With the Battery shutting down and then coming bacjk on for a short period and then switching off for a longer period this is the clasic sign of an Overload Occuring. Could be a short in th Battery causing the problem have you checked for voltage at the Battery Terminals?

Could be a Bad Power Supply/Mains Adapter so check the output of the Mains Adapter and then look at what is being offered tot he Battery at the M'Board side of things at the battery connector.

Reading the voltage & Current ratings wil answer your question.

Col

by robo_dev

if so, it could be faulty.

Measure the voltage of the battery when it shuts down. A faulty battery would tend to 'drop the load' without warning.

Also see if the battery is getting very hot. If the laptop is faulty and the current draw is too high, the battery may overheat and shut down.

by smokinjoe30

Okay...I'm not much of a hardware guy and I haven't ever tested voltage so how would I go about testing this stuff? I can get a multimeter from a friend, but what should the readings be and so forth? Thanks.

by robo_dev

by swapping them out.

It's rated as an 11.1V battery, but you would have to figure out what the pinout is. Typically there are four or six pins that connnect the battery to the laptop.

IF the battery is faulty, after it drops the load, I would not expect that the PC would be able to boot or operate normally from the battery...especially if it had overheated.

Is this a 'genuine Gateway' battery or a 'gateway compatible' battery?

The other thing to check for is if the laptop correctly indicates the battery charge level....if it does not, then you may need to do a 'Battery calibration' using a software utility that comes from gateway.

Note, however that a google search on 'Gateway laptop battery calibration' returned a couple of hits on "battery calibration killed my Gateway Mx6124 laptop!'

by oh smeg

Where the Electrical Rating is there is a Output Voltage and Current probably somewhere around 13 to 15 Volts and something measured in Milli Amps is the current rating of the Adapter.

This Voltage and Amperage should be present at the Plug at the end of the adapter where it plugs into the NB. Also double check the polarity just to make sure that someone hasn't tampered with the Adapter and wired it up wrong.

The Battery is Nominally 11.1 Volts so it needs at least 2 more volts to charge it so anything between 13 to 15 Volts should be present at he NB Connector to the Battery. The actual Battery should read somewhere around the stated 11.1 Volts with a fairly big error % so anything between 10.5 to 12 would be acceptable.

Col

by robo_dev

My HP laptop here has a supply rated at 2.5A.

I would expect that reverse wiring would result in 'magic smoke phenomenon'. Magic smoke is the smoke that escapes from electronic equipment that is very difficult to get back into the device.

My guess is that either the battery is faulty, or the battery connectors to the mobo are messed up somehow. One issue I've had is that the quality of these battery packs is all over the map...especially if it's a generic made-in-China 'compatible' battery pack.

by smokinjoe30

I have already obtained a new batt as per my original post. I attempted to do battery calibration on original batt and it came up OVER VOLTAGE and shut down...now whenever I connect the old batt to the laptop, the charging light on the front blinks red four times. When I hook the NEW batt up (Gateway, not made-in-china immitation) I don't get any RED light...but the purple light goes on and off, and so on as I stated in the original post.

I attempted calibration on the NEW batt and it states that it's "Trying to wake up primary battery". There is a spot on the screen that says Voltage Before Learning = 8186mAH.

I am never able to see if the laptop even reads the amount of charge left on the batt.

by robo_dev

It's starting to sound like either:

1) Interface circuitry built into battery(s) has failed or is confused.

2) Interface from Laptop mobo to battery has failed.

3) Calibration data is just hosed and needs to be cleared/reset.

I'm not sure how to reset calibration on that model. Some IBM Thinkpads had tons of problems with that....people were having to force calibration reset by putting tape over some of the communication contacts on the battery (with small risk of battery overcharge->overheat->fire->explosion).

On some laptops, resetting the bios will also reset battery calibration data. I'm not sure how to reset the data if it's stored in the crcuitry of the battery.

I'm sure you've already updated bios and battery calibration utilities.

From a voltage measurement standpoint, I would be curious if the battery that was detected as 'overvoltage' is really that way or not?

This discussion is closed to new replies.