Question Locked

Realtek AC97 removed from default options list

0 helpful
3 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Two days ago, after re-installing [updating] XP home, I installed Diskeeper 2007 on my system and ran both the disk defrag and then the Boot Defrag. Following these operations my sound stopped working.

The first thing I checked was my volume but couldn't open it "No active mixer devices" error. Searched forums and followed all options outlined to resolve this issue .... still nothing.

When I access my "Sounds and Audio Devices" through the control program there are several problems I noticed. On the "Volume" there is 'No Audio Device'. On the "Audio" and "Voice" tabs the default device is listed as 'Modem #0 Line Playback' AND it is the only item listed as a default. Prior to this I used the following as default 'Realtek AC'97 for VIA Audio'. This is no longer available as an option.

However on the "Hardware" tab, it is listed (along with quite a few others) and alll are showing as working properly.

Again, following much more searching of forums and following numerous options outlined I downloaded and installed the latest drivers for Realtek AC'97 (see below). I also downloaded, installed and ran "K-Lite Codec Pak" (suggested as a cure on one of the forums). Also as a result of a suggestion on a forum I re-installed the VIA drivers from the install disk. All to no avail.

In desperation I once again re-installed [upgraded] win XP home. This time at the end of the install I received an error message (which disappeared before I could make a selection, or fully copy the info) relating to an error on MS00BE.EXE which said something about audio & video and needing a file ff....and options to skip once, always, use once, use always. Before I cud select an option windows restarted and install ended.

Here are the Audio and Sound devices on my system from System Info:

Name Unimodem Full-Duplex Audio Device
Manufacturer Microsoft
Status OK
PNP Device ID MODEMWAVE\0\{4FD55569-6299-40BA-85E4-8A06149E0012}
Driver c:\windows\system32\drivers\modemcsa.sys (5.1.2600.0 (xpclient.010817-1148), 15.75 KB (16,128 bytes), 9/06/06 14:54)

Name Realtek AC'97 Audio for VIA (R) Audio Controller
Manufacturer Realtek
Status OK
PNP Device ID PCI\VEN_1106&DEV_3059&SUBSYS_B0101462&REV_60\3&13C0B0C5&0&8D
I/O Port 0x0000C800-0x0000C8FF
IRQ Channel IRQ 22
Driver c:\windows\system32\drivers\alcxwdm.sys (5.10.00.6240 built by: WinDDK, 3.84 MB (4,030,144 bytes), 9/06/06 14:51)

I still have NO sound. In WinAmp Config of Direct Sound it cannot get device info as it is in use.

I really do not want to have to wipe my disk and reinstall because of the number of applications I would have to re-install.

Any help would greatly be appreciated before I seriously consider going back to my ink bottle and quill ... NOT

With thanks

3 replies

by internetspider

Hi, Before u reinstall why u did'nt use system restore,
1. ok now go to mycomputer properties> (system properties)Hardware> device manager > from the list remove Realtek AC'97 Audio

press refresh (Scan for hardware changes) and it will display new hardwar found and then put ur Viachipset Ac'97 Cd it will auto detect ur driver,

2.if it is set up file then remove RTLAC97 in no.1 procedure then run setup and follow the screen, restart ur computer and check.

3.check ur audio connections and try to change and check ur speakers.

4.when u r in device manager select realtekAc97 Audio properties> Driver> Driver Details> write down these audio system files and delete them one by one and then restart ur system and try to install the driver.

Note: Make sure about the realtek Audio driver that it really for Realtek Via Audio Driver coz there r many virsions in that audio driver.

by ww1ace2006

You may well have heard the sigh of relief from Halifax, NS a short while ago.

As soon as I removed the Realtek using the device manager and clicked the Add New Hardware, the program found and installed driver automatically (I did not have to use my VIA disk. Just went in and re-set Realtek to my default device (it was now listed).

A very sincere and large THANK YOU for your assistance in this matter.

This discussion is closed to new replies.