50 replies
by cawaii Accepted solution
by oh smeg Accepted solution
If there has been a power spike these things get scrambled and the only way to fix that is to remove the power lead for about 30 seconds and then plug them back in and allow them to boot.
If there is a Battery Backup involved with this unit you'll need to remove that as well as the power lead. ;)
Col
by cawaii Accepted solution
by somesh.bsu Accepted solution
Reset operation returns the DLink Router to factory settings. You will need to configure it once again and specify your PPPOE options (if that is what is being used to connect to Internet) and setup the DHCP address pool along with ISP provided DNS entries. Refer to DLink DIR 655 manual available at this link: http://static.highspeedbackbone.net/pdf/D-link-DIR-655-Manual.pdf
That should help you set up things once again in under 10 minutes.
by cawaii Accepted solution
by kmthom Accepted solution
Try this:
1. Reconnect through the ROUTER.
2. Go to adapter settings and disable your network adapter, then enable it again. While you are at it, go to the properties of the network adapter -> Internet Protocol (IPv4) -> Properties of IPv4 -> check to make sure it is set to automatic on both settings.
3. Give it about 20 seconds or so, then bring up a command prompt. (Start -> Run -> type "cmd") Then type "ipconfig /all"
4. Let me know what it says.
If THAT does not help, try the following:
1. Plug back into your MODEM directly, giving you internet access.
2. Do an "ipconfig /all"
3. The IP address that is shown may have to be set as your Default Gateway on your router somewhere.
4. Also, on the router config, check your DHCP settings - post what you find if you need help.
About your worries with DYNAMIC and STATIC. For home use, DYNAMIC is typically what is used. However, it looks like DNS is the problem, not your router assigning an IP. The problem could be the network adapter (does wireless NOT work, but a WIRED connection work?), or the DNS on the router/modem is not talking with each other.
by cawaii Accepted solution
by kmthom Accepted solution
In that case I would check your DNS settings. Try www.opendns.com.
They have some free DNS servers you can try, namely:
208.67.222.222
208.67.220.220
Try plugging those into your adapter settings/router settings and see if that helps you.
by cawaii Accepted solution
by mfa9 Accepted solution
Reset the DIR-655 to factory specs, then start fresh. D-Link has some on-line wizards here:
http://support.dlink.com/emulators/dir655/121/Internet.html
That will guide you through the process.
by cawaii Accepted solution
by l_creech Accepted solution
by cawaii Accepted solution
by l_creech Accepted solution
It's always possible that could happen, but very rare.
Having reset your router I would suggest power cycling your modem (or even resetting it since it will retrain automatically with the ISP) and see if possibly that is where the real problem lies. Actually had to do this today with a Comcast device to bring a customers network back to life.
by cawaii Accepted solution
by l_creech Accepted solution
by monophysite Accepted solution
Reset the DIR to factory anyways. What have you got to lose?
Then follow the manual instructions:
http://static.highspeedbackbone.net/pdf/D-link-DIR-655-Manual.pdf
First Steps from Manual:
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modems power adapter. Shut down your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer.
5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot.
7. Turn on your computer.
8. Verify the link lights on the router. The power light, Internet light, and the LAN ligh....etc.
Reset the router, unplug, and follow these instructions.
Then use the wizard link above, or read more of the manual if you want to DIY.
by cawaii Accepted solution
by dayen Accepted solution
by mackman2011 Accepted solution
by gdeangelis Accepted solution
Can you take the ip address from your pc which is directly connected to your isp, and apply it to your router, removing the dhcp as you have suggested? This will remove dhcp on the outside connection. Make sure you put in the dns settings. Then plug your pc into the router and make sure you get an address. You didn't say if you had a private or public address from your isp on your pc while directly connected to it. If you are getting a private ip (192.168....) address, you may need to tweak your settings. Once you get it all working, take some screen shots and save it on your pc so you'll have them in case you need them later. Just to be sure, have you moved any cables during the process, or are they all as they were before the trouble hit?
You may need to cycle the isp modem as well.
by cawaii Accepted solution
by gdeangelis Accepted solution
by cawaii Accepted solution
by arujammer Accepted solution
by gdeangelis Accepted solution
Make the routers inside address 192.168.1.1 on the inside network and leave it dhcp assignes from hughes net on the outside (connected to the modem)
So inside 192.168.1.1 255.255.255.0 and the router will get 192.168.0.x from the modem on the outside.
by 1000064442 Accepted solution
by mfa9 Accepted solution
by mjd420nova Accepted solution
by mfa9 Accepted solution
by cawaii Accepted solution
My ISP is HughesNet, they're satellite~ my modem model is HN9000 if that helps any~ this all worked just fine in the past, tho when we first hooked it up it seemed we had to call D-Link to have them specifically tell us some stuff we needed to put in router, I can't call them now tho because I'm not under warranty anymore and they will charge me~ it was a hassle to set up but everything had been working fine for 6 months~ then a week ago the weather was a little cruddy so it was affecting the connection to the modem, I thought it was the router and reset it, now they're is no wireless internet~ =( I've cloned my MAC address, that doesn't do a thing~ tho my LAN MAC address is different and I don't know if that's the one I should be cloning? if so then I don't know how to do it, can't find the settings for it anywhere~ =P and ipconfig for the modem is,
Windows IP Configuration
Host Name . . . . . . . . . . . . : MOMS
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : Yes
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Intel(R) PRO/100 VE Network Connecti
on
Physical Address. . . . . . . . . : 00-12-3F-95-EB-0E
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.0.3
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
DHCP Server . . . . . . . . . . . : 192.168.0.1
DNS Servers . . . . . . . . . . . : 67.142.161.12
67.142.161.13
Lease Obtained. . . . . . . . . . : Wednesday, July 25, 2012 10:35:32 PM
Lease Expires . . . . . . . . . . : Wednesday, July 25, 2012 11:35:32 PM
by mfa9 Accepted solution
by arujammer Accepted solution
by mfa9 Accepted solution
by mainboard777 Accepted solution
unplug modem to reset it. wait a minute then plug in. do same for router after modem lights quit flashing. If they are same unit then hit reset switch according to manufactures procedure.
then power off cpu and restart after router is finished resetting (lights quit dancing )
Once restarted restart your wireless hookup procedure without password, unless your router is by default no wireless is turned on. if so go into router and turn on wireless then rerun hookup wireless.
by rob kuhn Accepted solution
Maybe get a new router and see if you still have problems.
BestBuy and Fry's Electronic are very good at accepting returns within 2-4 weeks of purchase. Just be sure to keep all the packaging, softwre, manuals, etc. It also helps if they're not torn and in "like new" condition - makes the return process easier and faster :)
Late last year our 3+ year old Wireless router started to act up. We were intermittently losing Internet access. At the time we weren't sure if it was the router or the cable modem.
I targeted the router mainly because of the number of years in service it has been. And it seemed like the perfect excuse to finally get an "N" Wireless router :)
Anyway, if after getting a new router and the problem is still present then you can start to look at your actual cable modem and ISP.
I know you said that connecting directly to the modem works fine but I've found that soemtimes rebooting the router (power cycling it) will clear up problems.
HTH and good luck!
by cawaii Accepted solution
by rob kuhn Accepted solution
I think power cycling at this point is moot. :)
One last thing you can do is to try and reload the firmware. Even if the firmware is current sometimes reflashing it will fix odd problems.
I've done that on some of my switches before. I've even uploaded an older firmware (like one version back). On some equipment you can't install a previous firmware version so it might not be possible.
If getting a new router works there still might be some hope for your old one. Maybe convert it into a repeater? Or just use the switch portion of it.
BTW, just to confirm your setup, you don't have anything sitting between the router and your cable modem, correct? In other words you don't have a switch in bertween the two?
by mackman2011 Accepted solution
If your IP address is static your ISP should give you the info you need (IP, gateway, and subnet). Satellite addresses are by and large static. Your router's MAC address should be on the router, on the label with the serial #, etc. This is your WAN MAC address. Your WLAN and LAN MAC addresses should be the same as each other and similar to the WAN address, the last pair will be a unit apart from the WAN, i.e. B4:7D to B4:7C. Your assigned WAN IP address from your ISP will be entirely different from your LAN and WLAN IP addresses. The IP addresses assigned to your devices connected to the router are dynamic. My home router's LAN IP address ends with .1 but the devices begin at .101 and change with re connection.
With your PC hard wired and connected you can get the ISP's numbers from your network connections. It's not unheard of for someone to just re enter the same numbers and click update or save and everything works. Go figure.
by cg it Accepted solution
and obviously the person who is having troubles did all the things one would do to fix the problem. After that, since the price of the router is $70.00 USD+ the amount of time spent on fixing it, costs more than simply tossing it and getting another.
That's my advice on how to fix it. Take a hammer, smash it, then go buy another. One will feel better after smashing to router to pieces and then getting a new one that works.
by balajistarrer Accepted solution
It looks like the dns address is same as default gateway.. Try to change the dns address to the following:
comodo dns :
primary dns :8.26.56.26
secondary dns :8.20.247.20
or
Nortan dns :
Preferred DNS: 198.153.192.50
Alternate DNS: 198.153.194.50
or even google dns..
Hope this would change your problem..
by rob kuhn Accepted solution
That's actually typical if the router is set for DHCP from the ISP and the router is providing DHCP and or DNS for the network.
Manually adding the DNS to the router would probably work but if the ISP changes it's DNS then obviously it will break. :)
by macgvr Accepted solution
If your satellite modem has a firewall, and I would expect it to, you may want to connect the modem to one of the lan ports on your router. You would need to turn off DHCP in the router and let the modem handle that. If the modem allows that and all the computers work, then all you really need is a switch and not a router. The only reason you might want a router is if you want a better firewall or you need to create firewall rules that the satellite modem can't handle. Given that the satellite modem has a firewall, (I hope it does), it will get tricky having one firewall behind another and creating access rules that actually work.
This should get wireless access working and you don't have to worry about getting the router configured to work with the modem. You won't need to replace your D-Link. Just use it as a switch instead of a router.
If you want to try to a static DNS that is not likely to change. Use either OpenDNS, IP address: 208.67.222.222 and 208.67.220.220, or Google, Ip address: 8.8.8.8 and 8.8.4.4
by geekmasterz Accepted solution
by yuvaaa Accepted solution
From the output seen for the modem, it is the IP settings that should be changed on the router's interface.
To do that, connect the computers Ethernet port and router's ethernet port with a ethernet cable.
-- Open the IE or Firefox on the computer, type 192.168.0.1 and press enter. You might be asked for username and password. Do nothing but click "OK".
-- Once you have the router's interface, click "Network Settings" on the left side of the page.
-- Under Router Settings section, change the router IP address to 192.168.2.1
-- Under "DHCP Server Settings" section, change the "DHCP IP Address Range" to 192.168.2.100 to 192.168.2.150.
-- Now click "Save settings" at the top of the page.
===============
-- Now unplug the power cable from the router.
-- Connect the modems ethernet cable to router's WAN interface.
-- Connect the power cable to the router and check for the usual lights(Ethernet, WAN/Internet).
-- Now, open IE or firefox to access the routers interface.
-- Click status and check for the "Cable & Network status", Ip address and Default gateway.. etc. You should see Ip address as "192.168.0.X". If Yes, you should be online.
by ebd79 Accepted solution
by decoderspot Accepted solution
Have you tried to Reset your router, then try Reset by pressing a small switch on the back side using Pen or a pin.
Then you have to Re Configure Router.
by decoderspot Accepted solution
Have you tried to Reset your router, then try Reset by pressing a small switch on the back side using Pen or a pin.
Then you have to Re Configure Router.
http://dadecoder.blogspot.in/2013/02/how-to-backup-and-restore-d-link-router.html
This discussion is closed to new replies.
Trending Networks posts
Sort by Trending