Discussion Locked

Windows 2000 hates me

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Okay, I bought a WD 30.7 Gig IDE hard drive, it was the best bang for the buck. First off the 1999 bios didn't discover it. After a technical call to WD, I added another jumper to the hard drive and it was discovered. I fdisked and formatted the drive via a Win98 startup disk. Then using this same disk I started up the computer and tried to install Win 2000 server edition. About 15 minutes into it (it was still copying files) I got an error message that it could not recognize my boot drive/device.

It told me to restart the computer and see if I got past this error message - I didn't. What IS the problem? I did install Win98 on it, it installed flawlessly. I tried to upgrade from the 98 version to 2000 and got stuck in/on the same error message. Help me.

The computer is running a Celeron 366 with 96 megs of RAM. A generic SIS 4 meg AGP video card. It has two net cards, a DVD ROM and a CD ROM. The hard drive is hooked up as a primary running off the number one IDE controller. The DVD and CD are primary and slave running off the number two IDE controller.

This should be a slam dunk - the only thing I can point at is the WD hard drive.

13 replies

by chris

I have seen this happen with my HP NetServer, and the only solution we came up with was updating the BIOS. Try to get an update to your BIOS and if that doesn't work try exchanging your WD for the same model to see if you have a bum HD. Hope this provides some help.

by mike.wagoner

Once again, the solution seems to be the bios - the bad news is that short of coughing up money - I appear to have the most up to date bios avaiable. Its an Award bios, version 4.51 and for anything more recent than that they want to charge a fee. I'm still debating if its worth it or not.

by jeffwatt

I've seen this type of behavior when the OS detects the IDE controller, but its not quite the right version. Try updating your BIOS, and check with the MB manufacturer to see if there's an IDE Controller driver available, and use it instead of letting 2000 detect the driver.
I'd place my bet on the BIOS, though, there's very few devices out there that 2000 won't detect.

by mike.wagoner

It likes everything up-to-a-point and yes, everyone seems to think bios. I tend to agree at this point but the blood suckers want to charge me to upgrade - what happened to the good old days.

by jlessick

You say you booted from a floppy? Did you remove it once the install started? Leave the boot disk in drive A or better yet try booting from the Windows 2000 CD.

by mike.wagoner

Yes, I did remove the floppy. The Win 2000 is an OEM version so it doesn't/won't boot from the floppy (I had tried that too). Thanks for the response.

by doubledown

I can pretty much guarantee it's not your hard drive (especially since it works under Win98)...I've got the same one and a very similar computer configuration, and Win2k Server installed just fine. I agree with the others, its most likely somethinga BIOS update will fix.

by mike.wagoner

Yeah, unfortunately they want a price to upgrade the bios (its an Award bios). I'm still debating on if I should give in to their blood money.

by kokleong

If you already have a backup of your data, try boot up from the Win 2000 CD and do the installation from there, you can change the boot up sequence from the CMOS menu.

by doc7213

I got the same error yesterday, with virtually the same machine. Here is what I found out from the "wizards at Microsoft" If the HD had a FAT16 and was changed to a FAT32 it will not work. The only way around this is to partition the HD and run aDual Boot with 98 and 2k. This is not what I wanted to hear either. There is a program on the Microsoft Win2K site that will check your system to see what needs to be upgraded, or what devices may be conflicting. If you can't find it email me andI'll get it to you.

by mike.wagoner

Remember, this was/is a new drive, it was not formatted at all. When I did format it, I formatted with a FAT32, so there was no change involved. If I had my way it would have been formatted NTFS.

Also when I was installing Win2K, it went through the check of the hardware, all it complained about was my SCSI controller. Even after removing it I still got the "can't find boot device" blue screen error.

Thanks for trying to help.

This discussion is closed to new replies.