Discussion Locked

windows can't open install.log

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
i have a dell opti-plex gx1 w/a 350mhz pIIand128 of ram.im having a problem getting the computer to recognise a new cd-rom that was instaled.the old one was replaced when i re-installed windows 98and the driver file disapeared after the instalation(the disk i used was a copy and i dont know if it is a second edition or not)i replaced the IDE cable when i got the new cd-rom and cant figure out what to do next.And on start up the instal wizard cant open INSTALL.LOG any help would be great...Thank you for your time

5 replies

by rabbit_runner

I am not certain if this will apply to you. But check out the following.
When you got your new CDRom, did it come with an 80 wire cable? Also was the cable on your old CDrom a 40 wire cable? If the original was a 40 wire and the new an 80 wire, a quick fix would be to go back to the 40 pin cable. The reason is that the different cables treat the master / slave settings differently.

However if both cables are identical, check to make certain that the master / slave setting on the new CDRom is identical with that on the old one.

If the computer can not find or see the cdrom, then the driver will not be installed. A way to check this is to re-boot your computer. When it first starts to boot up, find the key that will enter 'setup'. This is the CMOS setup. Sometimes it is F2, or DEL, or F10. Often during the boot up, there will be some instructions on the screen which will indicate which key to press. Once in CMOS, check in the Advanced settins area and see if the computer sees your CDROM. If it is not showing, then re-check your cable connections. If it is showing there, then Windows will be able to find the device.

If the device is showing, you will need to check the particular driver to operate this CDROM. Windows will normally load a generic driver which will give you standard funactionality with the CDRom, but may not give you all the features that the manufacturer put into the device.

Hope this helps.

by robert_benotti

thank you for your time...the IDE cable that came with the cd-rom is a 40 pin cable,all connections are tight,and the cd-rom is in the master possition in the secondary IDE port on the mother board and the computer still will not recognise the new hardware...i evenwent in to the device manager-settings-dule IDE channel settings to make sure both channels were selected... thank you for your time

by thechas

W98 often needs the IDE bus driver for the chip-set on the motherboard.

For a PII, you will need to go to Intel's archive if the chip-set is an Intel set.

http://downloadfinder.intel.com/scripts-df/Product_Filter.asp?ProductID=816

This file should be the correct one for your chip-set:

http://downloadfinder.intel.com/scripts-df/Detail_Desc.asp?agr=N&ProductID=816&DwnldID=4241

Remove any spaces from pasted links.

You might be able to get the drivers from Dell if you have the system serial number.

Chas

by robert_benotti

thank you for your time...to let you know the cd-rom dosen't work so im limited to using floppy's...the file you wanted me to copy and load was to big for a floppy...thank you again for your time

by thechas

If a floppy is the only way you have to transfer the file, then use WinZip or a similar program, and create a self extracting archive.

You can span multiple disks if needed.

What I do when I set up a system, is to mount the systems drive in my main PC and create a folder with ALL device driver downloads on the hard drive. That way, I have the drivers available to get things started.

I also copy the Windows CD, and install from the hard drive instead of the CD drive. That way, I never need the Windows CD.

Chas

This discussion is closed to new replies.