16 replies
Hi tomm344462,
I encountered the same issue with my 2003 server and the HPDJ 6940.The driver you suggested works a treat! Many thanks mate, youve saved me a a considerable amount of hassle.
thanks again,
Maurice
by herrerad
by larryl
by smiller
by standardit
by suewhitehead
by v_mathieu
(Sorry for my bad English, i' m French)
The installation of a Windows XP pilot for Windows Server 2003 must normally always function, because the only difference between these two systems is that Windows Server 2003 has a core more recent than that of Windows XP, therefore the pilots are inevitably compatible between the two systems.
But you know, HP, it are odd, then one should not seek to understand why it do not have to correct the bug compatibility.
Here is the solution:
Start > Settings > Printers and telecopiers > Files > property of the server > Drivers
Add > Next > Next > provided Disque > Browse >
Select the Cd reader which contains Cd of the HP drivers provided with your printer HP 6940. It must be called ?hppp?.
Select ?Autorun.inf? > Open > OK
Select in the list the ?HP Deskjet 6940 series? driver > Next > End
(The system copies the driver files required)
At the end, Click on ?closing?.
Here is, the installation of the pilot is to finish. It was not so hard, not?
This technique (if one can call that a technique) must normally function for any printer driver.
by kferraro1
by winstephen
In attempting to manually set the IP address on an HP 6940 I mis-typed it and now cannot find the printer on the network. (I typed 10.3.102.35 and it should have been 10.93.102.35.) Other HPs have a small button near the cat5 jack that wipes out any static address - but not this one.
winstephen@yahoo.com
by kferraro1
I have had to do this. These directions for a cold reset are from an HP discussion page. It will set the IP back to DHCP which you can then discover from your DHCP server.
Page 30 of the user manual available from: http://h10032.www1.hp.com/ctg/Manual/c00591688.pdf
says:
Follow these steps to reset the printer to the factory default settings:
1. Verify that the printer is powered on.
2. Press and hold down the Report Page button.
3. While holding down the Report Page button, press the Cancel button three times.
4. Release the Report Page button.
Regards,
Bob Headrick, MS MVP Printing/Imaging
by gmorrow913
Just wanted to say this helped me out as well and a quick GOOGLE search brought me your solution here.
Thanks again!
by dbreece
by serkanoney
Hi,
Many Thanks your solution this issue was solve my problem too. But there is one think you have to consider if you choose this driver, it creates character set problem and I try the other driver to fix and I found that 990c is more suitable.
by meyh
The model number [b]HP Deskjet 6940[/b].
[b]Method 1:[/b]
You may refer to the below links and use the troubleshooters. Check if it lists and helps resolve any issues: Open the Printer troubleshooter:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&tmp_geoLoc=true&product=46798...
[b]Method 2:[/b]
You may check if you have the latest drivers installed for the device. You may refer to the below link for getting the latest drivers and check.
http://www.hpdriver.net/hp-deskjet-6940-driver/
Good Luck.
by partizani
The model number HP Deskjet 6940.
Hi I can used this sahre and worked. succesfull
Method 1:
You may refer to the below links and use the troubleshooters. Check if it lists and helps resolve any issues: Open the Printer troubleshooter:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&tmp_geoLoc=true&product=46798...
Method 2:
You may check if you have the latest drivers installed for the device. You may refer to the below link for getting the latest drivers and check.
http://www.driverhp.net/printer/hp-deskjet-6940-drivers.html
Good Luck.
This discussion is closed to new replies.
Trending Networks posts
Sort by Trending