Discussion Locked

DOWNLOAD: 10+ tools you should have in your support tech repair kit

0 helpful
68 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

https://www.techrepublic.com.com/5138-10877-6046244.html

After you take a look at this download, please post your feedback, ideas for improvements, or further thoughts on this topic.

Thanks,
--The TechRepublic Content Team

68 replies

by 3xp3rt

Most important tool is an Universal RJ45 Crimping Tool, at cost of 17,5$

by gralfus

I ran into a situation at our college where we were using AMP brand plugs and a non-AMP crimper. The crimps were always faulty. If we used generic plugs, the crimps were fine, or if we matches AMP plugs to an AMP crimper they were fine. There were a lot of exasperated students for a while until we figured this out.

When I bought my modular crimper online (GMP Tools), it came with interchangable crimping irons, for phone, RJ45, and a separate RJ45 iron for AMP plugs, so this must be a known issue.

by glenn

I have stolen a makeup brush from a promotional pack that was given to my wife. Nice soft bristles make it easy to clean the dust off parts.

by too old for it

I have a Shark, and a kit of attachments I bought at a sewing machine store.

It works more wonders than just blowing dust around with a can of air.

by lipl1

Personally I perfer the 25 lb. sledge hammer myself. It resolves 99% of all hardware issues, always works, cheap to by and is the only tool needed

by rfishpool

At some sites I have visted 2 essential items

1. Very big hammer

2. Large bottle of scotch

by too old for it

I remember takeing a long drive to a welding supply house to install a network card.

Owner showed me the server (sitting next to his desk, of course) and a large welders hammer. Told me that if the server gave me any problems to give it a whack.

Obviously his method, as when I opened it up there was not a square or plumb surface in the machine.

by sandym

Don't forget a torch. I used to use a great little one that cost ?5 on e bay and also had a cigarette lighter (not that I smoke), but I now use an AA Maglite.

BTW - I never go anywhere without my Pocket Leatherman!

by ley1963

A Leatherman is essential. I have owned mine for 15 years and it still works great (looks good too). I just oil it every once and a while and it goes everywhere with my via a belt clip. Knife, screw drivers, file, pliers, and wire cutters. Most important, it has a bottle opener for cracking open that beer when he job is done.

If you go to their website, they also have a nice accessory kit you can buy that you attach to your Leatherman that gives you a nut driver. The little kit that attaches to your belt (2" by 2" square) holds this nut driver, and 6 tips. I have an additional Phillips, Torx and Allen tips. The actual nut driver attaches in simple but sturdy fashion (ingenious actually) and gives me more torque to turn screws along with the additional tips.

By the way, I have used a paper clip to open CDROMs that are broken or have no power. It is also great for reseting many many devices that give you just a little hole for the reset button. They are also great for holding papers together....wierd.

by nicknielsen

Many years ago, I purchased a Cordura belt pack that would hold a Mini-Maglight, an original Leatherman, a Buck Cadet pocketknife, and a pen. I think I paid US$10 for it. It's still going strong, I still have everything except the pen, and I still use these three tools for almost every routine job.

The looks on faces when you rebuild a PC or printer without a bag full of tools are absolutely priceless.

by tom

A few years ago I found a Mag Lite that uses 2 AAA batteries. Fits a shirt pocket much better than a AA lite, and seems to work better and longer than a single AAA lite. Searched all over this year, and no one seems to carry them. Haven't looked online yet. They're great if you can find them.

by peebriches

Paper clip usually used for ejecting cd's, but also good for poking beligerent users eyes out!

by bdowdell

I bought a $6. toolbox at a discount store and filled it with:
AA flashlight .99
2 types of tweezers $1.40
1 toothbrush .99 (for cleaning rollers on printers)
small bottle of Alcohol.
Pliers, Screwdrivers, Lithium grease, Cable tester, xtra 9v battery, xtra bios batteries, cable crimps, wire cutters, small bag of rj45's, labels, Property tags for inventory, small rachet set, can of compressed air.
Total weight: under 8 lbs.
Total time wasted by not being prepared: 0

by nicknielsen

Also essential in retail maintenance (point-of-sale) world for resetting devices, releasing cable latches, initiating register dumps, and repelling irritated store workers.

by graham

Believe it or not, the paper clip is actually the specified tool used by Mitel to shut down their PABX systems...

by sboverie

1. Straighten part of the paper clip and insert it into the tiny hole in the CD/DVD drive to remove the CD/DVD media or to just open the drive.

2.Use pieces of the paper clip and wrap them around your meter probe tips with a short length sticking out beyond the prob tip, use this for probing tiny connectors and other test points that are too small for the regular probe tip.

3. Use the paper clip to repair mechanical things, need a hinge pin, need a latch, need to short something together.

4. You can use a paper clip as a tool, although not as good as real tools, but when a need is there it can work. I have used paper clips as screwdriver, wrench, drill bit and an interlock over ride.

Be creative, don't look at things as what they are made to be, look at them as objects that have other uses besides what they are designed for. Forget what your shop teacher told you about using the right tool the right way for the right reason.

by evan

These little things make life so much easier. They can reach near anywhere and have excellent gripping power, no matter what the item. I thought that I was the only one who kept a pair in the toolkit... this makes me feel not as weird now! ha.

by markb

Put a dab of Blue Tac on the end of a screw driver. Great for getting those loose screws from awkward places. Its like having a magnetic screwdriver, except it picks up everything!

by pherdinand

I don't saw al your paper but you are a real IT PROFESSIONAL.
best regards.
ATT.FERNANDO ELIAS

by half9

I have a variety of software discs from a mag that has them every month ,,handy for adobe /spyware/ incredimail/and other must have programs. just load off the disc

by tbbrick

Cannot believe you left out a tone generator. Be it data cable or telephony issues, my TG has saved me boocoo headaches. Another thing I can't do with out is my Craftsman multi-head screwdriver. Can't lose the bits as they are stored in the handle. You twist the cap over the bit you want, tip it, and it slides out, then you snap it into place. Finally, my small jewelers screwdriver kit, not just for my glasses, but those itty-bitty screws on hard drives, et al.

What you haul all of it around in is just as important. I have two cases. I use a smaller fishing tackle-type box for telephony tools and parts. I have a canvas gatemouth bag for the bigger stuff such as a spare data cable, mouse, mouse pad, phone cable, power strip, and blank CD/floppies.

by bpate

Another really good telephone/data tool is an SLT cable tester. It's cheap and tests continuity but you can't beat it for troubleshooting cabling issues and testing your cable after you make one. I also carry a 66/110 punch down tool. I also love dental picks...they are great for getting into small areas to move something...

by ciderick

An absolutely essential bit of kit - the standard pencil eraser is invaluable for cleaning contats etc...

by sparker

I'm a long time tech on everything from TV's to high speed printers to you name it. One of the most important things in my tool bag was gouda cheese! OK, actually it was the heavy red wax that covered the cheese. There were times when you could not use magnetic screwdrivers, so I would keep a ball of wax in my bag to scrape some on the tip of a screwdriver and hold the screw in place while reaching deep inside a cabinet to insert a screw. Worked well with nut drivers too!

by good old dog

what I carry around in my trusty old bright red, plastic, nicely compartmentized tackle-cum professional toolbox.
Jumpers (it's amazing how many times they just mysteriously disappear), Q-tips (really handy for gunked up non-responsive trackball mice rollers), tweezers which are spring loaded closed, cheap cotton gloves (for handling video and sound cards)and the always important anti-static wrist band (most of the computers I see are on or near carpet).
I also keep various fans with me and an assortment of Torx bits ( quite a few of the older proprietary cases use Torx screws for the case and their drives).
All of the normal tools, bits and pieces are in there as well. I've probably left out something important.
Hope this helps.

by fungus-among-us

A Zippered CD case full of OS (especially LIVE linux discs) and utilities (spyware detectors and killbox) CDs. Besides a multimeter, I also carry a Power Supply load tester. A tube of Thermal grease as well as thermal grease/pad cleaner/remover. I recently also added a connector tool kit (by Rosewill). It includes 4 different tools needed to dis/reassemble any connector found in the PC. I also carry two of each type of Data cable (80pin IDE, SATA, & floppy) as well as spare SATA power adapters, Y-splitter power cables and your standard power cable. My laptop (with wireless and RJ45 ethernet) is also an essential tool. Another tool that has recently become essential (although it's on my keychain, not toolkit), is the 4GB USB flash drive. Rather than have anything loaded on it for use, I keep it empty and use it for data backup if the need arises.

Not in my toolkit, but in the trunk of my vehicle, I also lug around: (all known working parts) a 15" Color monitor, an old laser (6p) printer, a 40GB IDE drive, a 40GB SATA drive, a 24x CD-ROM, a floppy drive, a 350 watt power supply, an assortment of RAM (SIMMS, DIMMS, and DDR), an assortment of case fans, USB A-B cables, centronics parallel printer cable, a supply of RJ11 and RJ45 connectors, a spool of telephone wire and a spool of CAT5. When I make service call, I not only feel the need to diagnose the problem, but also feel the need to have the client up and running (if possible) while they wait for their replacement parts (mine are just loaners). Repeat business from my clients, and calls from strangers asking for computer repairs must mean I'm doing something right. (even though my hourly rates are 25-40% higher than all of the local computer shops)

by jkinsinger

You should always have masking tape with you in case you have to tape a stuck button in place, or need to tape the door shut on the back of a printer, or just want to tape the users mouth shut so they stop blaming you for their computer being broke.

by danielwoolsey

There is a tool out there that you can use to convert 3.5" / 2.5" / SATA hard drives to USB. This is a must, especially if you want to recover data from a laptop drive. or hook a drive up to a system quickly without opening the case. Find one, buy it, use it, you will love it, you will wonder why you didn't get one sooner.

by itpirate

The CD case (with DELL recovery CDs and Acronis Backup, et al), my jump drive and external HD are probably my most used tools but I also carry a lot of the same things that you do.

Unfortunately I don't have a car-trunk (I have a truck without a camper shell) to carry all the larger stuff.

You are most definitely a mobile tech like myself.

Tim

by vetch_101

I was going to say - I was amazed no one had mentioned live cds or drive cables...

Live rescue cds are a must! I've got loads of different ones, but Knoppix, BartPE disks, and (if you're willing to go a little to the dark side) Hiren's boot are all indispensible...

Also, a particularly nice bit of kit is one of those USB2 to SATA/3.5IDE/2.5IDE cables...
Basically means you can plug (almost) any of the disks you find into a laptop and pull off the data even if it's a non-booting and fairly dead disk...

Jx

by brian.kronberg

Add:
- An extra NIC
- a small switch (like a Netgear FS105)

Replace:
- 15" color with a 17" LCD. Saves gas :)

New:
I always carry a Linksys or Netgear firewall. It is an easy sell after a spyware or virus cleaning.

by whalesbulfs

it says there - paperclip (ofcourse). But WHY? I never ever use paperclip when repairing computer. what for???

by steveaaaaaa12

The paperclip is good for a number of things, holding wires, fishing small parts out, pulling jumpers, and of course the obligatory admission that you need to reset something, a butter knife won't fit everywhere!!!!

by mississauga99

Hi there - i would love to see a separate discussion on what sort of software support you keep in your kit! For example: spyware detection, backup software, virus removal software. I'd like to know what sort of software diagnostic tools everyone is using.

by angry_white_male

* Ethernet analyzer (check cables, length, pin-outs, connectivity, etc... - doesn't have to be an expensive Fluke unit)
* Probe and toner
* RJ-45 crimp tool
* RJ-45 connectors
* RJ-45 jacks
* Punch tool (66 and 110 blades - or whatever you use at your facility)
* Wire cutters
* Cable strippers
* Box cutter
* Butt-set (lineman's phone set)
* Small spool of cross-connect wire
* USB Flash drive with various utilities loaded on it and room to move files
* DOS network boot disk (or bootable CD or bootable USB flash drive)
* Ethernet crossover cable or adapter
* Ethernet patch cable
* Sharpie markers
* Pen and note pad
* Leatherman type of multi-tool
* #15 Torx drivers or bits (HP and Compaq hardware)
* Nylon zip-ties

by angry_white_male

* ESD protection (wrist strap)
* LED headlamp (looks dorky - but it works)
* Laptop (for you freelancers out there - get an old one on eBay)
* Cell phone
* Walkie-Talkies if you're doing cabling projects - less running around if you have a helper

by mark40930

In addition to those items mentioned, I also have a CD travel case containing Windows CDs (in case need to install on a standalone PC) and a Winternals utility CD that is handy to unlock the Admin account if it's locked out.
For the Ethernet analyzer I found that Fluke's Linkrunner is the best value for the money.

by exman

While I've got most of the suggested doo-hickeys mentioned, I rarely travel with them. I keep 2 screwdrivers in my briefcase - a normal phillips and a small slot driver. I also have a Swiss army knife, one of those parts-screw-grabbers and a jet drive with all the necessary diagnostic utilities and patches. In the trunk of my car I've got one of those cheap Chinese toolkits, 95% of which I never use (a soldering iron and a chip puller????) and a soft case with 2 or 3 external backup drives.
I've found that
a: Most problems I'm called out for are software issues and any hardware calls are mostly projects, not repairs. If they're repairs, I either just replace the busted part or take the box back to the shop.

b:
I can't take everything in the world with me and if I'm missing even 1 tool or part, Murphy's Law will make it the only part I don't have, so I have to go back to the shop anyway. I find it easier to just make a list of stuff I need while I'm at the site and when I go back to the shop, pick up all of the stuff I need for the job. It's cheaper than owning a panel van full of parts, most of which are never used.

by wayne

You must always have a pocket knife, I use it to cut and trim and also straighten bent pins. In place of nut drivers, I carry a 6" lock jaw pliers. The pliers grabs screws that are in tight and helps turn them.

by edwin.hills

I always carry a leatherman with a small strip of rolled up duct tape in the case. Many tools only 1 little package.

by jnjgoss

Ihave downloaded it three times and it always has a trojan in it and also never completes.

by rec

Hope everybody has a "funny bone". I've been doing hardware since paper tape and punch cards. I've also watched way too much TV. There are 3 tools I've always wanted, but never been able to get.
1. A "Bronson Rock". In the series "Along came Bronson" Michael Parks was able to repair anything on his Harley with a 10" cresent wrench and a rock. Rebuild a carb, repair a drive chain, over haul the engine... The magic had to be in the the rock.
2. A "MacGyver pocket knife". Richard Dean Anderson seems to be able to do anything with his. Maybe he used it to build the "Stargate"
3. A "Mulder Cell Phone" the one that works in a submarine under the polar ice pack, so when I can't fix something I can call for help.

by d-cat

[quote="rec"]1. A "Bronson Rock". In the series "Along came Bronson" Michael Parks was able to repair anything on his Harley with a 10" cresent wrench and a rock. Rebuild a carb, repair a drive chain, over haul the engine... The magic had to be in the the rock.
2. A "MacGyver pocket knife". Richard Dean Anderson seems to be able to do anything with his. Maybe he used it to build the "Stargate"
3. A "Mulder Cell Phone" the one that works in a submarine under the polar ice pack, so when I can't fix something I can call for help.[/quote]

1. A rubber mallet can get a jammed CD-Rom out of a case. Advised to only use on already broken stuff. :)

2. A Leatherman is the improvement on the Swiss Army Knife, and it goes everywhere I go. Speaking of MacGyver, don't forget the handyman's secret weapon: Duct Tape! What do you mean there's no free drive bay? :D

3. You could go with a sattelite phone, but I hope you're job pays well should you use that thing!

On a more serious level, other useful tagalongs could be a Laptop which you can connect any way possible (56K, WiFi, 10/100), just in the event you need to grab drivers for an obscure net card or something, and ways to get if from here to there: my lap case has in it a floppy drive and spare disks, null modem cable, laplink cable, USB connectivity cable, and a USB flash drive. I also keep with me a CD burner and a few spare CD's.

I usually just walk in with my custom UBCD4Win and my Leatherman, but I of course never know just what else I may have to grab out of the car.

by rogerf67

You certainly can do better than that.
Tools: A high-impedance volt-ohm meter, miniature soldering iron with solder, knife, jewelers screwdrivers, longnose pliers, regular pliers, adjustable end-wrench (small and medium sizes), small hammer (ballpeen), chisel (for metalwork) - more to follow:

by jufarah56

I'd say this covers it for checking on a desktop.
Might want to add a recovery disk but it all depends on where you're desktop is.

by randym55

a helper that won't shut up! That way you can do without a can of air (although it may be hot)

by jonathan

So to address some of the other comments while I am at it, presumably the multi-bit kit has torx drivers in it, and a really, really long phillips bit for getting at mobo standoff screws. It also presumably has magnetic bits, but the blu-tac idea is one I hadn't seen before.

I would add:

1. (and one already mentioned a Shark) is a handheld vaccum with decent power--in my case a Dustbuster with an long, slender attachment that narrows the tip down to 1.5"x.5"

2. A Giotto's Rocket

3. Cable management tools--A bunch of twist-ties and a nice assortment of zip ties in various colors and sizes.

4. Good, good quality electrical tape (like 3M Super 88).

5. A razor blade--comes in handy for the above as well as opening boxes, prying tiny things, etc.

6. Band-Aids (see above)

Not addressing software-based tools here.

by lipl1

Thats what I call those lights with a headstrap. The one I have has an angle adjustment.

by dark_knight

Through the years my box/bag of tools has changed as my job responsibilities have changed. I now have different tool boxes that I use depending on the job I am on. There are a lot of duplicate items between the two, however each has special items.

For example, if I am running wire then I have my kit with the crimps and ends, Tone Generator and sniffer. This kit also holds my Fluke, nice piece of equipment if you have the need for one and you know how to use it properly, but if you don?t, then save your money.
I used to carry a BNC crimp and ends but have tossed then after I figured I had not used them in nearly 7 years.
I know some will say that to have everything in one kit is better because you are always prepared in any case. Well true, but with the same logic, why not include every tool I have in my very large tool box. There are times I need a socket, and I have small little kits, again different bag for the jobs that call for them. I may take different ones in the car just incase. But when you are hauling around all the weight you will learn to take what you need. And if you don?t have you will just have to go get it.
Like the time I needed a hammer to fix a computer. Don?t carry one but needed it. Good thing was the client had one and let me use it.

Why did I need a hammer you ask? Well the computer in question that was shipped to them was, shall we say, not packaged properly. The box was dropped of the back of the truck and one of the corners on the case bent over so much that one could not remove the lid. The system would not power up and I needed to look inside to see what had been jarred loose when it collided with the pavement. The hammer was the only thing short of a cutting torch that was going to get it open. Once I hammered the case into shape I was able to asses the internals, reset the memory that had been knocked completely out along with several of the cards. Once that was done the system came to life. How the hard drive survived?

One think I did not see on the list or put forth in the comments was a mechanical pencil.
The larger ones are great for straitening out bent pins on all different types of connectors. Needle nose pliers are not the answer for this. And the smaller ones work on several of the different types of SCSI cables.

A bit of advice, for those that are starting up and making your kits, If you have any of those kits that they like to hand out for free, take my advice open it up and take all the screw drivers out and throw them away. Go get yourself some good ones. I use craftsmen, cheep and good for the most part. When it comes to the Philips Screwdrivers make sure you get a #2 Philips, most are not aware that the ones included in the free kits are not Phillips but a Reed and Prince AKA as a Fearson. These are the biggest culprits for reaming out Phillip screw heads. http://en.wikipedia.org/wiki/Image:Frearson_vs_Phillips.svg

by rand777

This is the most incomplete article I've ever seen. A complete tech's toolkit has not only the hardware but the software to fix a PC. I can attest that 90% of the problems I've seen are software related! Re-do this article like the pro's that you are and make it complete!

by danlanier

Since the thread is several years old, there is one item that might not had shown up initially that I find indispensable for tech support. It's a SATA/EIDE to USB adapter (with its own power supply).

Sometimes being able to snatch the HD out and stick on a secondary system as an attached USB drive is worth its weight in gold.

It's best to have a small pouch to put this unit in. I had an old IOMega Zip soft case that host my USB adapter. One of my favorite tools by far.

Anywho, best to you for this New Year

by mark

I worked double duty as a police officer and the computer systems administrator. I found the most useful tool was a Heckler and Koch P7 9mm semiautomatic. For some reason, every time I showed up, the problem resolved itself.

I don't know why, but the computer always knew when the gun was at my side.

This discussion is closed to new replies.