Discussion Locked

PIX 515E

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am trying to configure a PIX firewall 515E

I can ping outside from the firewall
I cannot ping outside from the inside network, but I can ping the firewall and configure the firewall with ASDM 5.01.

I think my NAT and ACL is probably not setup, though I have tried to do so, I have been unsuccesfull. Any help would be appreciated.

Here is the config:

PIX Version 7.0(1)
names
!
interface Ethernet0
nameif outside
security-level 0
ip address 63.201.112.138 255.255.255.248
!
interface Ethernet1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Ethernet2
shutdown
no nameif
no security-level
no ip address
!
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pixfirewall
domain-name bhccrane.com
ftp mode passive
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
monitor-interface inside
monitor-interface outside
asdm image flash:/asdm-501.bin
no asdm history enable
arp timeout 14400
nat (inside) 0 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 63.201.112.137 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00
timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 inside
dhcpd lease 3600
dhcpd ping_timeout 50

9 replies

by sureshkumar1982

Hi,
Pls check your PIX IP address 63.201.112.138 255.255.255.248. I think your PIX having the broadcost address. You suppose to use this range ( 6,12,18...120,126,132..138,144). So your PIX has invalid address.

by synner

Your ip addressing is correct... contrary to the other response...

However, you don't have a global (a pool of addresses on the outside) to nat to.

Remember, When you want to go from a high security zone to a low security zone, all you need is a translation (global and NAT).

by pilot80

Yes, that's it, but I do not know how to set that up and the ASDM is kind of confusing when it comes to doing NAT

by pilot80

That worked hehe
I used that in ASDM and created a NAT from inside to outside and it works

by deepsand

technical questions such as this belong in the "Questions" (formerly "Technical Q&A" - a much better name than the present one)forum, rather than in "Discussions."

by deepsand

Once upon a time the "Discussion" and "Technical Q&A" forums were quite different in structure and reached by separate tabs atop the Home page.

Now they share the same structure - other than the Name the only difference is the ability to mark responses as "Helpful" in the "Questions" forum - are reached by links co-joined on the screen, and lead to the very same introductory panel, such that it's not clear at all to many that the distinction between the 2 forums exists.

This discussion is closed to new replies.