Point to Point t1 Cisco 1841 File Sharing

Hello All,

I have a point-to-point t1 that I have a Cisco 1841 at each location. I can ping all interfaces on each router from both sides. I can even ping various computers on each side from the other side. I just can’t seem to share files from one computer to another. Below I have the configs from both routers. Any help is greatly appreciated.

Thanks!

RouterA#show config
Using 2149 out of 196600 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RouterA
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable password *
!
no aaa new-model
!
resource policy
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
–More–
*Dec 6 23:11:00.851: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed sip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip domain name yourdomain.com
!
username cisco privilege 15 secret 5 *
username * password 0 *
!
!
!
interface FastEthernet0/0
description LAN
ip address 192.168.254.2 255.255.255.0
speed auto
full-duplex
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0
ip address 192.168.250.253 255.255.255.252
no ip route-cache cef
no ip route-cache
service-module t1 timeslots 1-24
!
ip default-gateway 192.168.254.1
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.254.1
ip route 192.168.162.0 255.255.255.0 192.168.250.254
!
no ip http server
ip http authentication local
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
control-plane
!
banner login ^C
———————————————————————–
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username “cisco”
with the password “cisco”. The default username and password have a privilege level of 15.

Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.

username privilege 15 secret 0
no username cisco

Replace and with the username and password you want to use.

For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
———————————————————————–
^C
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet
line vty 5 15
privilege level 15
login local
transport input telnet
!
end

RouterA#exit

[Connection to 192.168.254.2 closed by foreign host]
RouterB#show config
Using 2264 out of 196600 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RouterB
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable password *
!
no aaa new-model
!
resource policy
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip domain name yourdomain.com
!
username cisco privilege 15 secret 5 *
username * password 0 *
!
!
!
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$
ip address 192.168.162.2 255.255.255.0
speed auto
full-duplex
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0
ip address 192.168.250.254 255.255.255.252
no ip route-cache cef
no ip route-cache
no fair-queue
service-module t1 clock source internal
service-module t1 timeslots 1-24
!
ip default-gateway 192.168.162.1
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.162.1
ip route 192.168.254.0 255.255.255.0 192.168.250.253
!
ip http server
ip http access-class 23
ip http authentication local
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
control-plane
!
banner login ^C
———————————————————————–
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username “cisco”
with the password “cisco”. The default username and password have a privilege level of 15.

Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.

username privilege 15 secret 0
no username cisco

Replace and with the username and password you want to use.

For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
———————————————————————–
^C
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet
line vty 5 15
privilege level 15
login local
transport input telnet
!
end

RouterB#