Discussion Locked

RUMBA 2000 AS/400 Sessions Hog Memory!

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Our corporation runs a standard of Win95b OS with RUMBA 2000 installed to connect to the AS/400. Lately we have had a rash of users complaining that they cannot do anything while running an AS/400 session, because they don't have enough memory. I have observed this incident and found it to be non-machine specific. Our machines are a minimum of 128mb RAM with a minimum of a P2-266 processor.

When the user receives the message that they are out of memory, they get a very-classic Win95 whitebox that says "Out Of Memory!" and to free up some resources. This can occur even after a fresh boot, with maybe one other program open in addition to RUMBA.

PLEASE HELP!
640k

13 replies

by tbradley

Since you say that this just started, I would look at the AS/400 side of the issue vice the Client side.

While not an AS/400 operator, I've been on the other side, and know that the IBM side
can "push" processes to the client side that
can seriously degrade the desktop performance. In my case, it was a sloppy
programmer who left in un-attended service pack updates, which ran hidden in the background regardless of the Client version.

by sixfourtykilo

That doesn't seem very likely since this AS/400 caters to over 1000 users, and locally we have 180 clients that attatch to it. Of those 180 clients, maybe 5% of them are experiencing this matter. It was suggested to me that it also might be a connectivity issue, but now that source and I aren't so sure about that since the AS/400 has made a recent transition to our location.

Thank you for your help!
640k

by tbradley

I think you've just answered your own
question, when you added the additional
information on the move.

1. How are your users connections made, Twinax, or Ethernet?

If Twinax, how many users/segments are on
each address chain? One little known fact
about twinax is that each 2 Balun or equivalent connection takes up one address chain.

2. If Ethernet, are your 5% of users on a
unique VLAN, or Lan Segment?

Also look at static vs DHCP.

Good Luck

by sixfourtykilo

That is a good point to make, however we are in an Ethernet environment using DHCP and our users are divided across 10 VLANs. it would be a long time before we ran out of IP addresses and because it IS a large corporation, static is out of the question. I don't think that when connectivity was suggested, it was meant on an IP level. In any case, these are PCs running RUMBA 2000 as stated before. This is seeming to become a rather complex situation. We have covered all of the basics, cleaning up garbage on the PCs, checking revision levels, etc. I have people at headquarters calling in to NetManage about this and many other problems, however I would like to get a head start on the issue.

Thank you again!
640k

by estebandelatorre

I don?t think that it may be a connectivity issue. (...a memory hog box?)
What I can?t undestand if it is machine dependant or client dependant.
Check this out. They may help you to isolate the problem.
1.- Disable Antivirus programs
1.5.- Try to disable any program, of those how run at boot time and leave an icon near the clock. They always use a .DLL that may ... you know it's windows...
2.- Try running rumba (if under TCP/IP) without being connected to the network.
3.- If the box stillappears, try CTL-ALT-DEL and watch for any extrange program.
4.- Delete temporary files! and perform a scandisk.

Good luck!
Oh..
Why 640K, Did it came from D.O.S ?
You can call me 1024K (640K plus allways unusable 384K more!!)

by sixfourtykilo

You would think these to be common-sense issues. We've performed the level 1 steps, cleanup, loading and unloading of programs, etc. Unfortunately because we're dealing with such a large company here and if issues like miscreant programs and/or virus utilities were causing the problems, it would be near impossible to change from say McAfee Antivirus to Norton Antivirus.

Additionally, its difficult to leave a user in a "crippled" state as it may prevent them from normal operations and I believe that it is just not an acceptable solution at this time.

I'm not convinced its a connectivity issue as well. These clients can connect with RUMBA while not logged on to the network, but it is undetermined if they will get the same errors. Leaving them in this state will also severely cripple the user as they will not be able to print or access shared files.

Thank you for your help!
640k

PS - yes 640k is from the old DOS. You can't beat the days when 6k of convential memory was night and day when it came to running a program!!

by estebandelatorre

I deal with more than 2100 as/400 users, and a mix novell + microsoft network, more than 300 printer and know how difficult/near impossible is to change some software, but "The decision day" allways arrived.
* Change IT now! or learn to live with it!
I have Elite/400 Reflection/400 and Host on Demand working on my environment. Also I've evaluated Rumba, but all of them have one thing in common: Very innocuos, like notepad.exe (except when file transfers and printer emulations are instaled!).
Best luck!

by sixfourtykilo

I'm sure that RUMBA was decided on for its ease of file transfers and large database administration. So far we're still bouncing around with our headquarters IS group, Netmanage and different discussion threads.

We're talking a 10,000+ user environment.. so changing one software that absolutely everyone HAS to use is near impossible.

I just happen to be a satellite site of the mothership. Here, we support 200 users, but we have to abide by standards.

640k

This discussion is closed to new replies.