NOC Questionnaire
Q1. Does Windows Server 2003 support IPv6?
A. Yes B. No Ans: A
Q2. How do you install recovery console? (assuming that your Windows Server installation is on drive C)
A. C:\i386\winnt32 /cmdcons B. C:\i386\Tools /cmdcons Ans: A
Q3. You want to install Windows 2000 Server on a computer. What are the minimum recommended hardware requirements to install this operating system?
A. Pentium/75MHz processor, 16MB of RAM, 400MB of free hard disk space
B. Pentium/100MHz processor, 32MB of RAM, 500MB of free hard disk space
C. Pentium/133MHz processor, 256MB of RAM, 1GB of free hard disk space Ans: C
D. Pentium/166MHz processor, 128MB of RAM, 2GB of free hard disk space
Q4. You are preparing to install Windows 2000 on a computer, and you want this computer to be able to dual boot between Windows 2000 and Windows 98.Which file system should you use?
A. FAT (or FAT32) B. NTFS Ans: A
C. HPFS D. You can use either FAT or NTFS
Q5. You are installing Windows 2000 Professional on a computer that is ?not? on a
network. When prompted by Windows 2000 Setup during the installation, what should
you ?Make this computer a member of ??
A. Domain B. Active Directory domain
C. E-mail group D. Workgroup Ans: D
Q6. What is the maximum number of primary partitions a basic disk can contain?
A. 1 B. 2 C. 3 D. 4 Ans: A
Q7. Which volume type provides high fault tolerance, has a high cost associated with it,
and provides normal speed of access to files?
A. Mirrored volume B. RAID-5 volume
C. Simple volume D. Spanned volume Ans: B
Q8. You want to analyze partitions on your Windows 2000 computer. Which tool should you use?
A. Disk Management B. Disk Administrator Ans: A
C. Disk Defragmenter D. Windows Components Wizard
Q9. What type of DNS domain is microsoft.com?
A. Root domain B. Top-level domain
C. Second-level domain D. Third-level domain Ans: C
Q10. You install the DNS Server service on a Windows 2000 Server computer. You
configure this DNS server to use a root server, but you do not create any zones
whatsoever on this DNS server. What type of DNS server have you configured?
A. Master B. Forwarder
C. Root server D. Caching-only
Q11. You want to configure a static IP address on a Windows 2000 Server computer on
which you want to install the DNS Server service and Active Directory. What tool should you use to configure the static IP address?
A. Ipconfig.exe B. DNS administrative tool
C. Active Directory Users and Computers D. Network and Dial-up Connections folder
Q12. You want to move the Philadelphia OU from the acme1.com domain to the acme2.com domain. Which tool should you use?
A. MoveTree.exe B. The move command-line utility
C. Server Extensions Administrator D. Active Directory Domains and Trusts
Q13. You want to assign a mandatory user profile to a user. What must you do?
A. Rename the user?s NTUSER.DAT file
B. Rename the user?s ntuser.ini file
C. Copy the Default User profile folder to the user?s profile folder
D. Copy the user?s profile folder to the Default User profile folder
Q14. You want to create a domain local group. Which tool should you use?
A. Local Security Policy B. Domain Security Policy
C. Local Users and Groups D. Active Directory Users and Computers
Q15. You want to use a single group to organize users from multiple domains that perform similar job tasks. Which kind of group should you use?
A. Universal group B. Global group
C. Domain local group D. Built-in special group
Q16. You recently created a Group Policy object (GPO) and associated this GPO with a particular OU. Now you want to link this existing GPO with two additional OUs. Which tool should you use to link the GPO?
A. Windows Explorer B. Internet Explorer
C. Active Directory Users and Computers D. Active Directory Sites and Services
Q17. You want to deploy a service pack for an application that was originally
deployed by using Group Policy. You copy the service pack files to the shared network folder that contains the application?s original installation files. What should you do next?
A. Remove the application B. Upgrade the application
C. Redeploy the application D. Publish the service pack as a new application
Q18. BetsyR is a member of one group,Technicians, that is allowed the Full Control share permission to the Support share. BetsyR is a member of another group,Managers, that is allowed the Modify NTFS permission to the Support share. BetsyR is not assigned any specific share or NTFS permissions as an individual user. What is BetsyR?s effective permission to the Support share?
A. Allow ? Modify B. Allow ? Full Control
C. Allow ? Read & Execute D. Deny ? Full Control
Q19. You want to add a printer on your Windows 2000 Professional computer that is connected to an HP JetDirect adapter that does not support TCP/IP printing.What should you install on your Windows 2000 Professional computer before you add the printer?
A. The DLC protocol B. The NetBEUI protocol
C. Print Services for Unix D. Client Service for NetWare
Q20. How can you redirect print jobs to a different print device?
A. Copy the print jobs from one printer to another printer
B. Assign the printer to a port that is connected to a different type of print device
C. Cancel all of the print jobs, then delete the printer. Create a new printer with the same name,
and assign it to a different port
D. Assign the printer to a port that is connected to another identical print device
Q21. You want to enable system access auditing on a Windows 2000 Server
computer that is a domain controller. Which tool should you use?
A. System B. Windows Explorer
C. Domain Security Policy D. Domain Controller Security Policy
Q22. You want to add the Recovery Console to the boot loader menu of your Windows 2000 computer. You place your Windows 2000 compact disc into your CD-ROM drive and start a command prompt. At the command prompt, you change to the drive letter of the CD-ROM drive, and then change directories to the i386 folder. What should you type at the command prompt?
A. winnt32 /rcvcons B. winnt /rcvcons
C. winnt32 /cmdcons D. winnt /cmdcons
Q23. You want to enable Internet Connection Sharing on a Windows 2000 computer.The computer has several existing connections. On which connection should you enable Internet Connection Sharing?
A. VPN Connection B. Local Area Connection
C. Dial-up Connection to Internet D. Dial-up Connection to RAS
Q24. You are manually configuring TCP/IP addressing information on a Windows 2000 Professional computer on your network. What should you enter in the ?Default gateway? text box?
A. The IP address of a WINS server on the local network segment
B. The IP address of a router on the local network segment
C. The local network segment?s subnet mask
D. The local network segment?s network ID
Q25. You are preparing to install Certificate Services for the first time on your Windows 2000 network. You plan to install Certificate Services on a Windows 2000 Server computer that is a member of the domain. You want the certification authority (CA) to be able to use Active Directory. Which CA type should you select when you install Certificate Services?
A. Enterprise root CA B. Enterprise subordinate CA
C. Stand-alone root CA D. Stand-alone subordinate CA
Q26. An administrator wants to use both remote administration mode and application server mode on a Terminal server, but cannot seem to get the configuration to work. What is the problem?
A. The server does not have the necessary system resources to provide both modes
B. The server is not in licensing compliance
C. Terminal Services does not support using both modes on the same server
D. The administrator does not have DNS configured correctly
Q27. When using remote control, how do you end the remote control session without ending your Terminal Services session as well?
A. Use the hot key combination you selected
B. Use the Shut Down command
C. Use the Kill Session command
D. Just close the Terminal Services window
Q28. You are the administrator of a Windows 2000 network. Your Windows 2000 Domain Controller had been in operation for one year. During that year, you have deleted numerous objects. However, the Ntds.dit file is the same size it was before you deleted any objects.
You want to reduce the size of the Ntds.dit file. What should you do?
A. Delete all the log files from the NTDS folder and restart the server
B. Use the Ntdsutil utility to perform an authoritive restore
C. Run the Esentutil utility by using the /d switch
D. Restart server in directory services restore mode and use the Ntdsutil utility to compress the
database to another drive
Q29. Your company?s network consists of two Windows 2000 domains: XYZ.com and sales.XYZ.com. The sales.XYZ.com domain contains one domain controller. The domain controller in sales.XYZ.com fails, and you do not have a usable backup. You want to delete all references to sales.XYZ.com in the Active Directory database. What should you do?
A. Delete the domain reference by using the Active Directory Sites and Services snap-in
B. Delete the domain reference by using the Active Directory Domains and Trust snap-in
C. Delete the domain reference by using the Ntdsutil utility
D. Delete the domain reference by using the Repadmin utility
Q30. You are choosing a Windows 2000 operating system to use on a new computer at your company. This new computer will be a heavily used SQL server in your enterprise network environment. Which operating system should you choose?
A. Windows 2000 Professional B. Windows 2000 Server
C. Windows 2000 Advanced Server D. Windows 2000 Datacenter Server
Q31. Which component in the Windows 2000 architecture supports the logon process and Active Directory?
A. User mode B. Microkernel
C. Win32 subsystem D. Security subsystem
Q32. In which part of the Windows 2000 architecture do applications run in?
A. User mode B. Kernel mode
C. Window Manager D. Executive Services
Q33. Which of the following is not a feature of Active Directory?
A. It is flexible and extensible
B. It is scalable to any size network
C. It provides ease of administration by utilizing group policies
D. It eliminates the need for trust relationships between domains
Q34. What is the minimum number of domains that a domain tree can contain?
A. 1 B. 2 C. 3 D. 4
Q35. Which master role causes the domain controller that performs this role to be the only domain controller in the forest that can add a new domain to the forest?
A. PDC emulator B. Schema master
C. Infrastructure master D. Domain naming master
36. For most large companies, in terms of ease of network administration, what is the optimum number of Active Directory domains to use on their Windows 2000 network?
A. 1 B. 2 C. 3 D. More than 3
Q37. You have fully routed TCP/IP connections between the three sites on your Windows 2000 network.You want to accomplish replication as quickly as possible between these sites.Which protocol should you use for intersite replication?
A. RPC over IP B. SMTP
C. DHCP Relay Agent D. RIP Version 2 for Internet Protocol
Q38. You want to use System Monitor to see how much of the paging file on your Windows 2000 computer is being utilized. Which counter should you use?
A. Paging File-% Usage B. Paging File-% Usage Peak
C. Memory-Pages/sec D. Memory-Pool Paged Bytes
Q39. Which base priority is assigned to most applications, by default?
A. Realtime B. High
C. Normal D. Low
Q40. What is the default optimization setting for the Server service on Windows 2000 Server computers?
A. Minimize memory used
B. Balance
C. Maximize data throughput for file sharing
D. Maximize data throughput for network applications
Q41. You install Microsoft Office on a Terminal server deployed in application
server mode by using Add/Remove Programs in Control Panel. What should you do next before Terminal Services clients begin using this application?
A. Install the multi session feature
B. Boot Terminal Services in Application Testing Mode
C. Run the application compatibility script for that Office version
D. Run Tstest.exe
Q42. You?re having problems with a Terminal server in application server mode. The server will no longer allow clients to connect, even though it has been working fine during the past few months. What is the most likely cause of the problem?
A. The server is experiencing system resource problems
B. The server?s free licensing period has expired
C. The server is not running TCP/IP
D. There is a problem with RDP
Q43. You just finished installing the Dynamic Host Configuration Protocol (DHCP) service on a Windows 2000 Server computer that is a domain controller on your network.What must you do before the DHCP service can start?
A. Authorize the DHCP server in Active Directory
B. Configure a scope, a superscope, and a multicast scope
C. Configure a DHCP address reservation
D. Configure the DHCP server for DNS integration
Q44. You are the administrator of a medium-sized private network. You have existing routers and DHCP servers on this network. You want to enable computers on your company?s network that use private IP addresses to communicate with computers on the Internet that use registered IP addresses. Which Windows 2000 feature or protocol should you use to accomplish this?
A. Internet Connection Sharing B. OSPF
C. NAT D. DHCP Relay Agent
Q45. You want to enable dynamic routing on a Windows 2000 Server computer on your TCP/IP network. You want this computer to manage the propagation of multicast traffic throughout your network. Which routing protocol should you use?
A. IGMP Version 2, Router and Proxy B. Open Shortest Path First (OSPF)
C. RIP Version 2 for Internet Protocol D. Network Address Translation (NAT)
Q46. You want to create a scope on your Windows 2000 Server DHCP server that will contain a range of Class D IP addresses so that the DHCP server can assign these addresses to client computers that request them. What kind of scope should you create?
A. A scope B. A superscope
C. A multicast scope D. Any of the above scope types
Q47. You recently installed WINS on a Windows 2000 Server computer on your network. Prior to installing WINS, you configured the computer?s local area connection with a static IP address. Because of your network?s size, only a single WINS server will be needed. What else must you do in order for the WINS server to begin providing NetBIOS name resolution services on your network?
A. Add IP address-to-NetBIOS name entries to the lmhosts file on each client computer
B. Configure WINS replication
C. Authorize the WINS server in Active Directory
D. Configure each client computer to use the WINS server
Q48. What is the most critical decision you have to make before you implement your Active Directory?
A. The name of the first domain B. The number of domains
C. The number of users D. The DNS Ans: D
Q49. You install a new server application on your Windows 2000 Server computer. Response times fail to meet user specifications. You want to use the Process page in Task Manager to find out whether the response time of new application would improve by the addition of one or more processors.
Which two columns should you select to view?
A. User Objects & I/O Reads B. I/O Writes
C. Memory Usage D. Page Pooled
Q50. Several factors must be weighed when deciding whether to use a workgroup or a domain. Which factors is the most appropiate, when present, indicate that a workgroup may be the best choice?
A. When the network consists of a small number of computers, and all of the computers run Windows-based desktop operating systems
B. When the network consists of a large number of computers, and all of the computers run Windows 2000 Server
C. When management does not desire centralized security or administration, and users are technically savvy
D. When centralized network administration and security is desired, and users have minimal computer skills and are not comfortable administering their own computers
Ans: A