Question Locked

Windows 2003 Enterprice server and RAID 5 (with 4 drives 0 ,1 ,2 ,3)

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi Everyone..

I need a big help, recently we bought a Dell PowerEdge 2900 server with PowerEdge RAID Controller 5/i, PCI-Express, Integrated AND Integrated SAS/SATA RAID 5, PE Raid Controller 5/i Integrated..

Operation system is windows 2003 enterprice server, now please tell me how can i configure raid 5 with four hard drives (300GB, 3Gbps, SAS, 3.5 inch, 10K RPM Hard Drive) for these specs. Your help is greatly appreciated..and thanks in advance....

8 replies

by csheppard

1. Go to Start and right click on My Computer
2. Click Manage
3. Go down to disk management
4. On any one of those disks that you want configured for Raid 5, right click on it (all the way to the left) and change it to Dynamic
5. Change all the ones you want configured for Raid 5 to Dynamic
6. Now click on any one of those disks AFTER you changed it to dynamic. (right click on it)
7. Click on New Volume
8. When you go through the Wizard, add every single disk you want as part of the Raid 5 configuration and click Add
9. Select Raid 5
10. Do a quick format with NTFS

Thats pretty much it.

by churdoo

The above post is describing the setup of a software RAID, which is fine if you don't have the hardware to support a hardware RAID.

Since you have the hardware RAID controller on that server, you're better off letting the RAID controller manage the arrays as it was designed to do and to reserve your precious CPU cycles for the server role.

The short answer to your question is that you
a) physically install the 4 disks into the server.
b) go into the RAID utility which you access by stiking a key as identified by the RAID controller BIOS during the server POST, OR if there's an O/S installed, go into the Dell PERC array configuration utility (I think Dell places their utility in lieu of the standard windows disk manager, or at least they used to).
c) within the array config utility you group the 4 new disks and then create your RAID 5 on the group of disks.

Having said that however, some questions. Is the Windows 2003 Enterprise Server O/S installed? What disks or array is the O/S installed on? Are you trying to ADD the 4-disk RAID5 on the controller with another array? Are you intending the O/S to be located on this RAID5 array? Is the server in Production?

by eelamt

NO, I haven't installed the OS yet. Just received the server from Dell couple of days ago.. and I want to install the OS on the RAID 5 .. do you need any other info.. help pls..

by churdoo

Since that's the case, you just have to start the server. While the server is going through POST, you'll see a message on the screen from the PERC RAID controller indicating a keystroke that you press to get into the onboard config utility (I'm an HP guy so I don't know the Dell keystroke from memory). Press the key to go into the array config.

Once you're in the array config, go through the menus to see if the array was setup as RAID 5 from the factory or delete any array and create new RAID 5 using all four disks.

Once you see your desired RAID 5 setup, save the settings, reboot, and begin your Windows Server install.

by ms

Your hardware is all ready... except that the RAID level may not have been specified when the server or ordered... You will have to configure it for RAID 5 which will require you to scrub/format the hard drives and re-install all software.

Make sure you have backed up all data since nothing will be recoverable once the configuration changes. Your only next option will be to scrub/format!

Call Dell 800-WWW-DELL and with the service tag number, you'd be on your way in minutes

The process will take about 3-4 hours!

Good luck

by yvan.fournier

We have the exact same configuration here and did all that. Now when we get into windows and we check in the "computer management" under "disk management" we get that the c: drive uses 12 gigs for the system and the rest of the virtual disk is "unallocated". We read a bit an found out that we have to create an extended partition...which we did using the entire "unallocated" space (we are still not sure it was the right thing to do). The next step is to create a logical partition so we can assign a letter to it. That is where we are stuck. Should we create one big logical partition with the entire disk? It is asking as well to format (NTFS)...is it not going to erase the raid-5 or replace it with a software one?

Thanks,

Yvan

by churdoo

A 12GB system volume is a little tight for Server 2003. Over a very short time, the O/S will bloat and you'll find yourself filling up the system volume, and that's a pain in the a$$ to fix once you're in Production. If you have not gone into Production on this server, then I would re-install your O/S from scratch, this time creating more like a 30GB system volume.

After that, yes, in Windows / Disk Mangler, create an extended partition taking up the rest of the volume, and then create volumes(s) within the partition. Format as NTFS Yes, no question.

As for how big or how many volumes to make? Well that all depends on what the server role will be. Myself, I like to put System, Application executables, and logs on RAID1 volumes and data on RAID5 volumes, but the important things for you are that you're using RAID, you've got the System volume of sufficient capacity, at least one other volume for whatever role this server will be doing, and that you're careful not to install things on the system volume, i.e. c: drive.

This discussion is closed to new replies.