Question Locked

Wireless networking an Inspiron 1200

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I called DELL they said all there Inspiron 1200s have internal antennas. I searched for it and there is no internal antenna. How do I network wirelessly? I put in a mini-PCI card, but I cannot pick up any signals whatever.

8 replies

by mjd420nova

The small WIFI antenna is part of the card itself. The small card behind the door on the bottom, not the memory cards, has a small printed circuit trace around the outer edge that serves as the antenna.

by johnkenn777

Thank for your reply.

My dilemna is the only Wi-Fi mini-PCI card I could find that would work in the Inspiron 1200 is the MSI MP54G4 RT2560F Wireless-G Notebook Mini-PCI Card. It requires that the laptop have an internal antenna.

Thank you for all your help.

To your knowledge are all Inspiron 1200s supposed to have an internal antenna? I read that one of the cons is no internal wireless capability, but manufacturers like MSI have made the cards now.

by oh smeg

If you have the Hardware and software correctly installed do you have a working WiFi Access Point where the NB is. This needs to be on the 802.11 Protocol and you need to switch the Card on with a combination of the Switch on the side of the NB and if you have Bluetooth the Keyboard Keys which can toggle between WiFi & Bluetooth.

As for a Aerial this should be a white wire with a gold clip on its end on the Inspiron 1200 as per the Owners Manual displayed here under Installing the PCI Mini Card.

http://tinyurl.com/432xwx

This clip slides onto the PCI Mini Card and locks in place about half way down the clip. The bit that it clips to is a round looking pin with a Shoulder on it. You slide the Clip down the Pin till it locks in place you do not push it onto the Pin as this will not connect properly.

If you have a more modern PCI Mini Card the Aerial can be etched onto the Circuit Board as a trace around the outer edge of the Printed Circuit Board but if it has the option to fit the NB Aerial to use the Aerial as it will allow better reception. The aerial lead should be held down with some sticky Gaffer Tape under where the WiFi card screws in. If there is one fitted to this NB, you may be required to unscrew the WiFi Card to gain access tot he Aerial Lead.

Col

by johnkenn777

Thank you for the quick reply. It is crazy how difficult it seems to network a laptop wirelessly. I have an old Biostar board MKVD in my pc and I have no problems connecting it wirelessly to my Belkin Wireless G Router. What is the purpose of having a mini-PCI card slot in a laptop if you can't use it.

Here are the router and MSI mini-PCI card names:

MSI MP54G4 RT2560F Wireless-G Notebook Mini-PCI Card

Belkin Wireless G Router- 2.4GHZ 802.11g
Model F5D7230-4

The laptop is Inspiron 1200
Service Tag: 83Q6061

I thought the Service Tag would tell you the build of the laptop. It just shows a bunch of parts.

Thank you for all your help.

by oh smeg

With a PC it is very unlikely to be moved around so it doesn't require the same level of Security to prevent Intrusion that a Mobile Device that can be connected to many different WiFi Systems does. It also is only connected to the 1 WiFi Access point so there is no need to build up a Data Base of User Profiles to use the different Access Points.

This is your PCI Mini Card

http://www.msicomputer.com/product/p_spec.asp?model=MP54G4&class=com

The problem here is if this card was not supplied by the NB maker it may not be compatible with the NB that you are attempting to fit it to. As the Genuine Product is more expensive than the After Market offerings many attempt to use the After Market Products and they just are not compatible with the hardware that is it fitted to. In the case of WiFi Aerials the Maker will reserve the right to incorporate Design Changes as they see fit so with a newly developed or supplied WiFi Card they may no longer need a Aerial in the NB but a after market WiFi Card that is stated to work with this model NB will not have a Aerial built in and requires the one that was in a older version of that Model NB so you have an immediate problem arise here.

As far as Dell's Service Tag's go they show the exact components inside the unit that was supplied so you have the correct hardware configuration for that Particular NB. Dell do this by listing the Parts used to make the NB when it comes to identifying the actual NB and with the service Tag you will only be forwarded tot he actual Drivers that the item uses not the complete Drivers for that Model of system. The use of Service Tags refines the search to the exact hardware used to make the NB.

Col

by bens

When you inserted the Mini-PCI, you should have seen two wires (one primary, one secondary) taped next to where the Mini-PCI wireless card would normally go. These antenna cables normally run up and under the keyboard then around the LCD. It is possible that they are tucked uder the keyboard if they weren't taped down.

Is Device Manager picking up the wireless card? Do you have your wireless switch on (either by a physical switch or a 'FN' + hotkey)?

If all else fails, save yourself some time/headache and go with a wireless PCMCIA card which would have a built-in antenna. Sticks out the side some, but easier to install if you can't find the antenna wires anywhere. Just a thought.

by cfrobw

I have an Inspiron 1200 which I purchased in 2005 directly from DELL. The only option they offered for this model for wireless networking was a WiFi PCMCIA adapter card. They didn't offer an internal wireless option like it's twin the Inspiron 2200. Why I don't know. However last year I was really getting tired of inserting and removing the PCMCIA adapter so I looked into adding the internal miniPCI wireless adapter myself. First I checked Dells website to see which cards they had drivers for. I wanted the best card that I could find. I chose the one that had Wireless A B and G. I caught the card on ebay really cheap. I receieved the card and installed it along with the driver and had the same problem you had. After doing some research I found that there is supposed to be an internal antenna that is strung out in the LCD lid. So I looked around some more and found an internal LCD antenna for a Dell latitude/Inspiron on Ebay. I purchased it. When I receieved it I opened opened up the laptop and removed the cover from the LCD panel. I got some foil tape thats used for taping air conditioner ducts together. I put the metal antenna tabs in the top of the LCD panel and ran the wires down down carefully through the right side hinge area in and around to the miniPCI card and snapped them onto the card. Then I pulled the wires back leaving a little slack and started taping the antenna wires in place. I reassembled the lid and the rest of the case and now my Inspiron 1200 has internal wireless. It can even be turned on or off by pressing Fn+F2. It's really neat because of the A B G protocols, the wireless adapter shows you in a list all of the access points and shows which each protocol in running on each access point. I wish they would have had a MiniPCI card that had Wireless A B G and N on it.!

This discussion is closed to new replies.