Discussion Locked

Wireless Router which can issue in the 10.x.x.x subnet

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,

I am looking for a wireless router which is able to issues Ip's in the
10.10.x.x subnet instead of the 192.168.x.x range.

Like for example, the ones that linksys and d link make issue in the 192.x.x.x
range - someone told me that WLS-108MBPS from 3 Com can issue in the 10.x.x.x
range.

What do i need to look for in the technical specs before i buy it?

Thank You.

15 replies

by lowlands

As far as I know almost all of the wireless routers you can get allow you to specify the subnet you want to use. I have a linksys. By default, most of them are set up with an 192.168.x.x ip range, but you can change it to whatever you want it to be

by curlergirl

I have never heard of a router that could *not* issue IP addresses in whatever range you want to define. The DHCP server on a router works just the same way as the DHCP server on any other machine. Almost all routers I know of are issued with a default IP address and DHCP range in the 192.168.0.x or 192.168.1.x range, but you can change that. All you need to do is configure your computer to use DHCP, then connect to the router's control panel through a browser (if it has a browser interface) or through Telnet, find the router's IP address and DHCP server settings and change them to use whatever subnet you want to define.

Hope this helps!

by mehuls

Hi,

Thanks for your reply. I have a Linksys Wireless G broadband router (WRT54G).

I have tried to do what you have suggested.

1. navigate to http:192.168.1.1./ and put it the username and password.

2. That takes me to the setup of page where I see the following options:

+ Local IP address: which defaults to 192.168.1.1
+ Subnet Mask: where their is a drop down box - with the following options:

255.255.255.0
255.255.255.128
255.255.255.192
255.255.255.224
255.255.255.240
255.255.255.248
255.255.255.252

and the default selected is 255.255.255.0

+ DHCP Server - Enable or Disabled options

the default is Enabled

+ Starting IP Address:

their is only one Starting IP Address:

192.168.1. x

where in you can input anything in x.

My problem is that if I change the Local IP Address to 10.10.250.1, select the appropriate subnet mask, say 255.255.255.0 and I want DHCP to work - how do i make the starting address come from the 10.10.250.x

whereas the only thing that I can change is the x in
192.168.1.x !!!

Thanks

by educated_1_2

I see what you mean. I have the same router at home. It doesn't look like you can change the 192.168.1 in the "starting IP". But, I think that it is just a default field. I would try and change it and see what happens. I assume you already did, but if not, just try it. If you can't, hack the router or go buy a new one. We use Cisco 800 series at work (I think), I know they are programmable to 10 network.

by mehuls

okay - when I buy a new router what do I need to tell the sales person so that I dont need up buying a router like the current Linksys one that I have?

Are all Cisco routers programmeable?

Thanks,
Mehul

by w2ktechman

in the DHCP properties area. I have an 5 yr. old Linksys (not wireless) that allows multiple scopes.

by bcpgm

When you change the Local IP Address to 10.10.250.1, what you are doing is to define the network as 10.10.250.0 and the gateway address as 10.10.250.1. You could actually assign the gateway IP address as 10.10.250.254. Because the Subnet Mask was assigned as 255.255.255.0, the router acting as DHCP server will assign hosts (Servers, workstations, network printers, etc) IP addresses ranging 10.10.250.2-254.
There will be exactly 253 available IP addresses for the hosts; 0 for Network, 255 for broadcast, and one for the gateway (typically 1 but you can assign any between 1 and 254 inclusive).
In wireless network, you can combine wireless and wired hosts. Because of practical limit for the wireless, the number of wireless is limited to 32.

Once you change the IP address (10.10.250.1), you may have to reboot the computer to take effect.

by bcpgm

The total number of available IP addresses is 256 and three are reserved; Network (0), Broadcast (255), and Gateway.

by bcpgm

I have a Linksys WRT54GS v4 wireless router and I can change any in the Local IP Address. In fact, mine is 192.168.10.1.

by mehuls

That's in the class C range i.e 192.0.1.1 to 223.255.254.254.

I want mine in the class A range which is from 1.0.0.1 to 126.255.255.254.

More specially, from 10.10.250.1 onwards.

Rgs

by bcpgm

You have to CHANGE the Local IP Address to 10.10.250.1 and leave the Subnet Mask to 255.255.255.0.
This means the Router IP or the Gateway IP is 10.10.250.1. The number of available IP addresses will be 253; 10.10.250.2-254. By now you see the Starting IP Address as 10.10.250.x and the value of x is up to you. If you have 50 hosts, it could be any number between 2 and 205 inclusive. The Subnet Mask (SM) is also up to you. If you want to maximize the number of IP addresses, the SM should be 255.255.255.0. If you want to subnet, you can choose 255.255.255.128 and so on. The Local IP Address could be 10.10.250.100 because this is just the Router (or Gateway) IP address you are assigning. However, you want to make sure the IP address is not assigned to any other host. This is why typically the extreme end (1 or 254) is used as default so there would be no confliction problem.

by mehuls

I changed the local IP address to 10.10.250.254 and therefore, as you point out, the gateway address becomes 10.10.250.254.

What was greyed out i.e 192.168.1.x where x was the only thing you could change.

However, I restarted as you suggested and the 192.168.1.x changed to 10.10.250.x so problem sorted!!

Now to connect to the router i type http://10.10.250.254

The router is now able to issue the Ip's in the 10.x.x.x subrange!! And I agree that the D Links are better than the Linksys.

Thanks for the help!!

by jmgarvin

My wireless router is 10.60.foo.bar.

If Linksys won't do it, that D-Link will do it for sure.

This discussion is closed to new replies.