Question Locked

1720 router with ADSL wic

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello everyone, new to site, i have a 1720 cisco router with a ADSL wic card,the router with the version it has was able to do all the configuring for vc mode (atm-vc-if)(saw it and did it myself)?? Now the problem i did a reload on it (yes without backing it up like a dummy), after the reload it will not take any pvc mode or DSL commands, even said it in the show diag when i did it, is there any commands i have to enter to get it back or do i have to download something--i am lost, please help from anyone would be great, thanks alot-- BOE-- The Show version is Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-K2SY7-M), Version 12.1(5)YB4, EARLY DEPLOYMENT RE
LEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Tue 03-Jul-01 19:41 by ealyon
Image text-base: 0x800080E0, data-base: 0x80B3540C

ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-K2SY7-M), Version 12.1(5)YB4, EARLY DEPLOYMENT RELEAS
E SOFTWARE (fc1)

Router uptime is 2 days, 8 hours, 36 minutes
System returned to ROM by power-on
System image file is "flash:C1700-K2SY7-MZ.123-7.bin"

cisco 1720 (MPC860) processor (revision 0x601) with 24576K/8192K bytes of memory
.
Processor board ID JAD051707U5 (4023631964), with hardware revision 0000
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
--More--
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

thanks again Boe

6 replies

by netman1958

2 lines of your show version output don't jive. It appears to have booted
ROM: C1700 Software (C1700-K2SY7-M), Version 12.1(5)YB4, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)

But this line shows a different image:
System image file is "flash:C1700-K2SY7-MZ.123-7.bin"

Could you run "show flash" or "dir" and post the output?

by mikebobski

Router#show flash

System flash directory:
File Length Name/status
1 6046364 C1700-K2SY7-MZ.123-7.bin
2 860 BristolPTP-New
3 214115 crashinfo_19930301-003554
4 210694 crashinfo_19930301-010737
5 217280 crashinfo_19930301-003739
6 257327 crashinfo_19930306-091055
[6947028 bytes used, 1441580 available, 8388608 total]
8192K bytes of processor board System flash (Read/Write

by netman1958

run the command "show run"
and look to see if there is a line that starts with "boot" for instance:
"boot system tftp" or something similar.

by robo_dev

Plug in the cable set the auto mode and no shut it. Until that is physically working you will make no progress.

have you moved what slot the wic is in?

show service-module serial [SERIAL INSTANCE]

The WIC T1 DSU can provide a payload loop back. A loop back button is receded on the visible side of the WIC T1 card. Using a pen or a small screw driver press the button once. A LED labeled LP will illuminate orange when the loop back is enabled. To disable the loop back press the loop back button again.

The integrity of the serial WIC interfaces can be tested using the following command:

test service-module serial

The debug command can be used with the serial WIC interfaces:

debug service-module

This discussion is closed to new replies.