Question Locked

Acomdata 320gb USB 2.0 work in Vista?

0 helpful
3 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Any way to get this to work on Vista? It worked on my WIndows XP but ever since i switched computer with Vista, it does not work.

3 replies

by rob miners

you normally get an error message if there is a USB problem. Did you get a message of any description that may help us to diagnose the problem. Here are a few things to check.

We recommend that when you install the Drive, you connect it to a USB port on your computer rather than to a USB hub. Once the installation has been successfully completed, you can then connect the Drive to a USB hub if you so choose. We recommend this approach because if you experience a problem during installation, it will be easier to troubleshoot if a USB hub is not used.

Troubleshooting for PC Users

The power will not go on when I turn on the Drive.

A: Make sure your connections are secure.

My computer does not recognize the Drive.

A: Make sure all of your connections are secure. If you have an add-on card, make sure it is working properly and/or update the driver. Also, make sure you have all the latest updates for your operating system.

When I leave my computer idle for a while and come back, my AcomData Drive won?t work properly.

A: The most likely cause is that your computer is going into Sleep mode. The immediate solution is to restart your computer. To prevent this problem from reoccurring, go into your Power Settings/Energy Saver and set it to where it never goes into Sleep mode.

My AcomData Drive feels warm when it?s powered on. Is this dangerous?

A: When in operation, the Drive may feel quite warm to the touch. This is normal.

The Drive gives me a ?Device cannot start. Code (10).?

A: This is a power issue. Make sure your connections are secure. The other possibility is that the Drive has malfunctioned and requires service.

I don?t see my AcomData Drive in My Computer, but it does appear in Device Manager. (Windows XP & 2000 only)

A: Right-click on My Computer. Select Manage in the pop-up menu. In the Computer Management window, select Storage, then select Disk Management. In the Disk Management window, you should see a list of available storage devices. Look for the Disk that has a capacity closest to your AcomData Drive. Right-click on the right-hand box; in the pop-up menu select Delete Partition. Once you do this, it will say ?Online? & ?Unallocated.? Right-click on the box and select Create New Partition in the pop-up menu. When the Partition Wizard appears, select Primary Partition and click on Next. You will see a default value for the AcomData Drive; click Next. You will then see a drive letter (you can change this drive letter if you wish); click Next. You will then be asked to format the AcomData Drive.

When I try to format my Drive in Windows 2000/XP I get the message: ?Could not complete format.?

A: This problem can occur if you are using an expansion card to connect the AcomData Drive. Plug the Drive into a data port on your computer and try the format again.

You may also come across this error if you are using Windows 2000 or XP and you try to format the AcomData Drive using the FAT32 file system. If reformatting the AcomData Drive and you do not need Mac compatibility, Windows 2000/XP users should use the NTFS files system.

After I connected the Drive to my PC, I got the following alert message: ?Hi-Speed USB device plugged into non-Hi-Speed USB Hub.? What does this mean?

A: Windows 2000 and XP users will get this alert message if you plugged the AcomData Drive into a USB port that only support USB 1.x. This is fine, except your AcomData Drive will operate USB 1.x speeds (up to 12 Mbps).

When using a USB 2.0 connection, the Drive seems to be operating slower than the rated 480 Mbps.

A: First, In order to reach USB 2.0 speeds, you need a connection that supports USB 2.0. If the connection only supports USB 1.x the Drive will operate at USB 1.x speeds (up to 12 Mbps). The Drive will auto-sense the speed of your USB port and adjust between USB 1.x and USB 2.0 speed. Second, 480 Mbps is the maximum speed of USB 2.0 devices. Actual data transfer rates will vary depending on a number of factors, including available CPU resources.

The User Manual

http://www.acomdata.com/AcomData_Downloads/3.5_External_Hard_Drives/E5_Series_Hard_Drives/M-E5.pdf

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by oh smeg

On what happens when you plug the drive into a Vista Box. If you get the Found New hardware thingy appear but it fails to mount the external drive look in Device Manager to see if the drive is actually present.

If it is and it was formatted on a Unpatched XP computer the Partition Information may not meet Vista's Security and it will need reformatting to be usable on Vista. If that is the case you'll need to copy the contents of the drive to a different computer not running Vista and then plug the drive into your Vista Box and format it. You can then return it to the other computer and copy your Data back to the drive and it will be readable on Vista.

If the External Drive isn't present in Drive Management it is possible that the Chip Set used in the Case is incompatible with Vista. There was one specific SIS Chip Set being sold in the early Vista Days that was not usable with Vista. I'm not sure about other Chip Sets used in USB Enclosures but it is possible that the Chip Set used is not compatible with Vista or it may be compatible with Vista but not Vista SP1.

Col

This discussion is closed to new replies.