Question Locked

Building a Cd burner tower, Is my thinking correct?

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have been helping out friend that has a music studio. I offered to help build a cd burning tower to get production rolling.

My thoughts are: He haa a suitable case that I could use if i upgrade the power supply. I would like to upgrade the mother board also ( very old ). Also I planned on using a PCI SATA card with RAID on it, for the optical drives.

My question lies on the SATA card and how and will a burning program recgonize them as one drive? What tweaks or configurations may I have to apply for the drives to be reconginized as one. Any suggested configurations or specific hardware would be helpful.

Thanks in advance!!

17 replies

by robo_dev

if just dupe them, then buy a cheap $200 duplicator box.

Making CDRs for mastering is another story....

by matthewgillespie21234

Yes, but I wanted to light scribe them as well. Also to have a opprtunity to have a learning expierence.

by slayer_

And when your system boots, it acutally has its own BIOS, I have 2 CD drives hooked up threw it.
The bios seems to figure it out nicely, and Windows some how hides the fact they are attached that way.
The only time I've ever had issues with them is when installing WIndows, and in VM's the CD's don't get recognized. In everything else its normal, including burning situations. I copy discs with them all the time, they are 2 seperate drives.

by oh smeg

The PCI RAID Card has it's own BIOS and you'll need to configure the Array as a Mirror not anything else here. :)

But it should treat the 2 Burners as 1 Drive. Though you will need a Blank CD in every drive whenever you burn anything you will not be able to burn Single Disc's on the RAID Array. But if you have an IDE Burner fitted you can select that drive for single disc's.

Depending on just how many copies you need to make at a single time though you may be better off with a Dedicated Duplication machine that connects to a computer with a USB Lead and will burn up to 50 Copies at a time. These have a Arm that picks up the Blank inserts it into the Burner and then when it is finished removes it from the burner and places in on a spindle of burnt Disc's then picks up the next blank and repeats the process over again till either the Blank Spindle is empty or the desired number are burnt.

Verbatim used to have one of these models available and for small number duplicating it works well I have been told.

Col

by slayer_

It shouldn't be setup to Raid, thus assigning everything attached to it it's own drive, which is I thought what you wanted.

Otherwise, when your system Completes POST, your screen will black out and you will see another BIOS load up, this new bios will say which key to press. This BIOS display usually takes half a second, so look fast!
Remember you can use your keyboards Pause key to pause the bootup at the bios.

by matthewgillespie21234

Thank for everyones input, I will be posting later today the hardware specs to make sure everything is compatible. Thanks again!

by oh smeg

Or from the Drivers depending on how that particular Chip Set Works and if it is Jumpered or Software controlled.

So [b]Read the Manual[/b] that comes with the card to find out how it works.

Col

by slayer_

That can be used to boot from to install RAM drivers for any future OS installs in the same session. And then you also need to install them permenantly into windows afterwards.

The only pain is when Windows feels the need to restart during the install, cause you gotta redo the RAID drivers lol.

by matthewgillespie21234

i wait until the install is done then add the pci card. Wait till that is recognized then start adding drives?

by oh smeg

If you are planning on using a single Optical Drive connected directly the the M'Board. And you couldn't configure a RAID for the DVD Burners.

So how what do you plan to boot this system off to do that and what is the point if you don't have a RAID Array?

You need to use a RAID 1 Array here to just in case you don't know which is which and how they work.

Col

by matthewgillespie21234

I was going to use a ide cd rom that was already there for the install. Then add the devices once the install is done.

Windows will promt for third party RAID drivers and i could just get it done all in one shot?

by slayer_

so that should work :).

Just make sure you install the RAID array drivers before you let windows try and configure them.

by oh smeg

Just be careful to make sure that you manually configure the RAID to only the DVD Burners as if windows has it's way you may find out that you have a trashed OS/Boot Sector on the HDD.

Col

This discussion is closed to new replies.