Question Locked

Building my 9th Custom computer, but this one's not working.

0 helpful
22 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Okay, I'm not a complete newbie, just very close. I've built 8 custom computers for myself and my family, and I did a little trouble shooting for some of them, but I got them all there relatively easily. This one though is not going. I've got a "PCChips P17G Motherboard - V1.0, Intel 945GC, Socket 775, MicroATX" and a "Intel Pentium D 925 3Ghz DT 800FSB Socket 775 processor" along with "Dual Channel Supported 667MHz DDR2 ram" (Which had been used in a previous computer, but works fine.) Anyway, now that I have it assembled when I turn it on, the harddrive light comes on and stays on. The fans span, but that's about as far as it goes. Not even pressing the Num Lock will toggle the Num Lock light on and off. I don't even get a boot code. Honestly, it's like the ram is not reading. At least in my mind. Anybody else have an opinion?

22 replies

by willcomp

Ensure that CMOS reset jumper is in normal position.

Is 12VDC auxiliary CPU power connected (4 pin square plug)?

If neither of these are the cause, disconnect everyting not required for a basic boot and start there. You should only have motherboard, CPU, memory, PSU, keyboard, and monitor installed/connected.

by dr.llvll

Yep, I had the four pin plug. Honestly, that's my most frequent mistake. But no it was plugged in. I tried the CMos. Nothing. Now, I'm not even getting a beep code out of it. Here's a really dumb question. Does the beep come from the mother board or some external wiring to the case? So is it possible it's trying to beep but I didn't wire it to the case correctly? Oh, and would it hurt if I tried a 800Mhz ram chip in a 667Mhz board? I have one for a different computer and at least it would be a check if that would work.

by cg it

but with everything there is always the one that doesn't work. It's possible the board doesn't support the memory your trying to use.

then again it's possible the board is just dead.

If you bought it from Newegg.com RMA and get a different one.

by willcomp

Did you reduce down to bare essentials as recommended previously?

Most motherboards have a piezoelectric (button) speaker mounted on the motherboard. If there is no speaker connection on the front panel connector block, speaker is surely integrated on mobo.

If removing/disconnecting anything not needed for a basic boot does not help, remove memory and see if it beeps.

You did use standoffs to mount motherboard in case and did not place a standoff where ther was no screw hole? Either one can cause a short.

by dr.llvll

I got this one from Tiger Direct, but I haven't have any trouble return items with them either. Before I go ahead and give up though. Does anybody know if testing the 800Mhz ram in the 667Mhz board will hurt either? It's just one more thing to check.

by cg it

he's the resident hardware guru...

I don't think that mainboard will it take PC2 6400 memory [800 Mhz].

If you don't have any DDR2 PC2 5200 memory you might consider getting a 1 GB stick. Newegg.com has got 1 GB of it for around $25.00. [OCz brand].

by dr.llvll

I just want to know if it'd be damaging to try 800Mhz in a 667Mhz board. Does anybody know?

by willcomp

Using DDR2-800 memory will not damage anything -- either motherboard or memory. In theory it will downshift without any problems, however some motherboards are ticky about 800 MHz RAM especially Intel 965 chipset based boards. It has to do with voltages and SPD reporting. Still will not damage anything -- just won't boot.

by dr.llvll

I'm going to try the powering it up with no ram to see about a beep code. I didn't try that. Thanks for the advice. Other than that though, I was carful about the little feet thing and made sure they were only on holes. Thank you though for the note. Anyway, yeah, I also tried the stripping everything out. I'm starting to think it's a bad mother board. Not sure though. It's just irritating....

by willcomp

PC Chips has a habit of shipping mobos with the CMOS jumper in the Clear instead of Normal position.

I know that you checked this earlier, but wouldn't hurt to double verify that jumper is in Normal position. It will definitely prevent booting.

by dr.llvll

I did try that on several occasions unfortunately. Now, I just remembered though, that I had another motherboard sitting around. So I switched out the motherboards, and the computer doesn't work with either! Now, I'm starting to wonder. Might it be the processor? Has anyone ever heard of a processor Dead on Arrival?

by cg it

are you sure you have the 4 pin CPU power connector seated right?

by dr.llvll

Yeah, I checked that several times. It also occurred to me that maybe the Power Supply was bad since that's also new. Actually, I think I got another one floating around. I can test that.

by cg it

I'd return both the motherboard and the processor.

I know PCChips are decent boards though their failure rate is going to be higher than main name brand boards. I had to buy a PCChips board simply because it was the only Socket A boards available at Newegg.com. They weren't rated very high because of failure rates.

If you need an LGA 775 socket for that Pentium 4 processor, try the ASRocks boards as an inexpensive alternative to Asus, Abit ECS,MSI,Gigabyte. [though I have a preference to MSI Gigabyte makes good and inexpensive boards.

Might also consider going to AMD Dual Core Socket AM2 . you can get an AMD dual core for under $100.00 and a decent name brand board board for around $80.00 [Newegg.com of course]

by dr.llvll

I guess I will be just sending it back. I'm sick of the head ache, and I'd rather start back at square one. Anyway, thanks again everybody. You've all been really helpful.

|\/|ark

by cg it

there's that helpful button that gives a thumbs up..

Willcomp needs some of them thumbs up..

by mellow52

I have had it that if the heatsink with paste does not sit firmly and well on the processor that it will heat up so fast and senses it that it will refuse to go any further. Double triple check you have the heatsink / cooling fan on good.... must use paste. If it was ram you would be getting beeps.

by willcomp

The purpose of a minimal boot configuration is to reduce the possibilities and facilitate troubleshooting (fewer components involved). Swap any other components you can - power supply in particular.

When building a PC, I recommend you assemble basic system on a workbench or table top and test prior to installing in case.

by thumbsup2

In the old days (yeah, I'm OLD), processors arrived DOA all the time. Today, I would hope their QA has gotten better. But, one arriving DOA is not unheard of.

by willcomp

While I agree about checking HSF, you won't always get beeps with faulty RAM.

This discussion is closed to new replies.