Question Locked

Cannot see Harddrive in XP

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

So I won't get anyone confused I will number the Harddrives I am talking about:

I have hooked up an IDE harddrive(1) to my PC which runs XP off a SATA harddrive(3). It works fine.

I have another slightly older IDE hardrive(2) that used to be IDE hd(1)'s slave.
When I tried to hook it(2) up to transfer data to SATA hd(3) XP found the harddrive and said it had been installed, but when I go to My Computer it's not listed.

What can be wrong? I have used the same cables for the hd that worked.

Thanks in adavance

6 replies

by hal 9000

If so the most likely thing is that you don't have the correct Jumper settings on them set. If you have placed the original IDE HDD back into the system as a primary or Master it firstly should be booting off that and if there was no SATA Drive installed while it was the Boot Drive it's unlikely to be seeing the SATA Drive.

The other potential problem is if you have just added the older IDE HDD to the system on the IDE Lead and it's set to Master with the first IDE Drive set the same way there is a Hardware clash occurring of if it's st to CS Cable Select it may not be active so go into Computer Management look up the rives and see if th IDE Drive in question is shown there. If it's not then you have a Hardware clash with incorrect jumpers setting being the most likely culprit.

If it's shown there but not active post back with the actual message that is being given about the drive.

Col

by mr_cod

I went into Computer Management and something is showing up. It lists the HD but it seems to be inactive, only listed as "Foreign" and no indication of how big the drive is.

I also "pretended" that I was going to install XP and found the drive, but it was not assigned a drive letter. This is the message I got

" -: Partition1 [Dynamic Volume] 57239 MB 0MB Free "

The drive was very full when the PC died on me, but I would imagine that it had more than 0 mb free.

Thank you for your reply.

by hal 9000

There could be a problem with the Partition as it may not be readable by XP. The FAT 16 and lower are not readable and if you had a FAT 32 partition it's possible that the File Allocation Tables got scrambled when the computer died.

As this is an IDE drive you could try a Windows 98 Boot Floppy and see what the drive Format is. It's also possible that when the computer died that the drive may have been damaged and you need to apply some Data Recovery Methods to recover your data.

The best Data Recovery tools are listed here and while my pick of the lot would be the On Track one it's also the most expensive and fastest to use as it only takes a short time to reconstruct the drive while most of thew others will save files by type and you'll loose their previous names.

http://tinyurl.com/pfuhz

http://tinyurl.com/6vef4

Warning here Win Hex is an excellent tool if you know Hex Inside out if you don't use Davory which is slower but far easier to use and you are unlikely to do any more damage than has already been done.

http://tinyurl.com/rmvrv

http://tinyurl.com/nc4kx

http://tinyurl.com/kdeu

http://tinyurl.com/70lc

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

I haven't used all of these only the Win Hex and On Track which where both excellent Utilities. The Get My Data Back is supposed to be made by Forensic Data Recovery staff from the Federal Data Investigations Computer Crimes Squad but as I've never used this product I'm not sure how well it actually works and the other one that I've heard good things about was the Stella product which according to another TR Peer is a good program.

If the data recovery program that you select recovers data and writes it to a drive you need to remember to write it to a different HDD to the one that you are attempting to recover it from or you will overwrite other data and it will be unrecordable.

I hope that is of some assistance.

Col

by hightower_uca

Simple. If you have installed the drivers for the IDE card correctly then all should be well. Follow these instructions : -

1st click on control panel

2nd click on Administration tools

3rd click on computer management

4th you will see a small screen broken into 2 parts

left side has computer management (local), system tools, storage, and service and applications.

double click on storage

Then click once on disk management

You will notice the screen is now broken in 3 parts.

The Middle lower is what you will be concentrating on scroll down using the scroll bar in that section until you find the undefined drive.

Right click on the drive, and then format it.

follow the instructions quick format if new drive full if used. Win XP should assign a letter to your drive when viewed in My Computer after format.

If not then follow these steps given here except instead of format choice letter assign when right clicking your drive.

BE CAREFUL YOU CHOOSE THE RIGHT DRIVE BEFORE FORMATTING.

by daveah

That got me through to my 160g hdd that wasnt playing the game but now it ready to go thanks again

This discussion is closed to new replies.