Cat 5e Wire
I need to know what each wire does in cat5 cable. In our office we might be putting in a new phone system and I need this information for reference.
Thanks,
Andrew
Andrew-Poe@cericus.com
IT Employment
I need to know what each wire does in cat5 cable. In our office we might be putting in a new phone system and I need this information for reference.
Thanks,
Andrew
Andrew-Poe@cericus.com
by tomsal
Hi.
First, unfortunately I have the information you are asking in one of my great reference books I own --- but I left it at home today.
Secondly, I'm curious....if you are putting in a brand new phone system in this day and age -- its probably a VoIP phone system, if that's the case you don't need to know squat about what any of the wires functions are in a CAT5e cable.
Voice and data co-exist "automatically" in a VoIP system.
Otherwise, I can bring in my book tomorrow and post the info.
by oz_media
I YOU are installig a new phone system, be advised, if it is proprietary (NOrtel , NEC, Panasonic, Toshiba etc.) your warranty will be void as soon as you punch it down. These manufacturers have EXTREMELY strict regulations as to who can cable systems for them, they ofer specific product training to authorized dealers only and even those dealers cannot send out techs that are not specifically trained on specific product installs.
If you are wondering about your BIX rack ad what to puinch down, you are in for some serious problems.
No help sorry, just food for thought as I have seen this same instance at least 40 times now and in EVERY case, the warranty is void instantly, even if cabled by a reseller that is NOT a specifically trained and authorized dealer.
by rwhite
by tomsal
by Jay Garmon
Download: CAT 5 Patch/Crossover Cable Creation Guide
https://www.techrepublic.com.com/5138-6249-729182.html
Download: RJ-45 module installation guide
https://www.techrepublic.com.com/5138-6249-729104.html
by mshultz
If your system is a VoE or VoIP it'll be the same as data(unless you have some weird system). You can even use your existing data network to hookup the phones. It's like this, someone correct me if I'm wrong on the PoE pins.
Pins 1&2 and 3&6 are for data Tx&Rx
Pins 4&5 are not used as far as I can remember.
Pins 7&8 may be used for Power over Ethernet if you set it up that way for your phones(which is actually kind of nice).
Also, if you integrate your data and phone networks, you may want to look into getting 802.1Q/p capable equipment that allows for prioritization and QoS functions. Implementing that with my phone system has reduced any impact the VoE box would have had on my data network.
by mlayton
by oz_media
I don't know how many times our telephone techs and cabling techs have walked into an office where the IT staff have connected their own equipment and SOMEHOW it worked but the entire system was cabled and programmed wrong.
Many IT staff seem to tghink telephone systems are as easy to vable and configure as a network. Often they will get it to work but at about 50% of it's features are useless and/or line cards are not installed to the right ports etc.
I spent three years learning Nortel and NEC cabling, I STILL need to up my installation certs wit hNEC in order to install the newer PBX's, or else they just void the warrenty if it is not called in by a certified tech with a specific system cert number.
It is FAR more sophisticated than setting up even a complex network.
Makes you wonder about how much trouble NEC etc go to in order to make it difficult as the cat5e standard is an extension of the telecommunications standard and the in wall cabling is pin 1 to pin 1 etc. I can see how you would need to know the machine specs if you were hard wiring cat5e into the system but if it has an interface panel then it should not matter.
It may be a bit different if you route the phone through a switch or router, I just patch past as they are not part of the data network where I have dealt with them.
BTW I have done a few local adjustements simply by cutting the cable and crimping cat5e terminators to the end of each half, making sure to get the wire colour code order the same in each half. they always worked.
The Cat5 and Cat5e cabling in walls etc is, except for mistakes and cross over cables, pin 1 to pin 1 etc all the way through. Thus you only need to ensure what you have going in on one end is matched at the other. I used Cat5e to patch phoines through my house just by making sure that the phone cable into and out of the Cat5e sockets were wired the same.
Anyway as regards Cat5e and telephone, the cat5e standard is absed on the old telephone standard thus the middle two wires are the first twisted pair, the wires on each side of this is the next twisted pair (this is exactly the same as a four wire telephone socket) then the next two pairs are placed on on each side of these four.
If you consider the pin numbers as being from left to right as 5, 6, 3, 1, 2, 4, 7, 8 then the pins 3, 1, 2, 4 are eaxctly as a phone socket cable pin set up.
by oz_media
There's nothing to it BUT ANY shorts, opens etc will destroy a 40,000.00 PBX so they only allow certifed technicians to install.
There are a LOT of really minute adjustments that need to be made to high end PBX's in order for them to operate at thier best, this is why I said it may work, but not as it should. They are just too easy to screw up and I have seen mroe than my fair share of people who are 'IT gurus' that completely botch an install.
My point is that if you ae wiring a proprietary PBX or even a KSU, only user a certified installer or dealer (many dealers say they are NEC or Nortel approved, but they are not. There is a huge grey market they ae trying to extinguish so they are being EXTRA picky).
In the case of these systems, kiss your warranty goodbye and be prepared to pay for your $1600.00 line cards when/if they die. Or pay the $120.00+ epr hour to have a certified NEC/Nortel tech install it.
Just a heads up, I am not defending them, I just know how they work and have seen more than a few companies get stung when they say "ahh, what can there be to it?".
sounds like they need a better design. I can understand that a short could kill a card but it should not stuff the whole box and dice. And an open line should stop that line from working but should not cause any trouble to the hardware itself.
The PBX should come such that you just check the lines then 'patch' in. About 20 years ago I helped install a PBX and the connection to the building phones was a thick pile of twisted pair cables, the full colour went in the top row and the same colour with the white strip went in the bottom row of the phone gang box. If one of the lines from there was wired wrong then a fault light showed when you hit the test button. If someon ran power back down the line then a card blew and you lost 5 lines until you put a replacement card in, after testing each line on that card.
Can't see why they made it harder, this sort of increased difficulty would discourage me from buying their gear.
by sleepin'dawg
by oz_media
NEC is one of the top selling telephone systems in the world. They are extremely easy to cable but SHOULD any problems arise, the entire cabinet is voided, even if it is just a single card. Proprietary equipment manufacturers are really picky about this, (Panasonic, Nortel, Mitel Avaya, 3-Com, Toshiba, NEC, etc.)all void your warranty if they find out it is not a licenced install.
With NEC they have unlock codes for new PBX software and unified messaging systems, you MUST have an NEC tech code in order to call in and get the unlockcodes. They will provide the coeds based on your registered tech level so if you haven't trained on a speific PBX, you cannot get the codes.
I see many people buying systems at auctions or liquidations that are completely useless and they end up buying new product because (a) made in a different country (US and Canadian equipment is not compatible) (b) software level is too far out of date (c)cabinet is obsolete or missing cards that are no longer available
People seem to think a phone is a phone and many waste money looking for shortcuts and deals that just don't exist.
I readily understand your problem. The paperless office is a reality I have worked in one, mind you they had no papers that were required for legal or tax reason which is why they could get away with it.
OIur laws, and most country's laws, require original documents with original signatures for many things and these make the paperless office impossible for most people.
radio communications is an other area where the obvious is not always what happens. the closer to the source the stronger the signal, the more chance that the signal overflows into nearby frequencies causing problems. One reason why I stay with cat5e and keep away from WiFi (sounds like a bad lap dog, don't it, here Wifi).
The basic telephony technology is simple, covered it in my Base Cabling Licence, ie learnt how to wire up a PBX etc. The problem is the way some companies are going about and deliberately making it difficult. In the early days of computing each company went its own way and did the same sort of thing, any work by anyone but our approved techs means violation of warranty, after a time they saw this was not good in terms of long term viability; the PBX people should read the lessons from history and stop making it harder than it should be.
Most countries require you to have electronic equipment certified as compatible with the national stuff prior to being able to sell it, and
Aust is this way.
I can understand the company saying that you MUST have a certified tech to work on their software, but saying you must have their certified tech to lay cables that are supposed to be done according to a national standard is absurd, yet (it appears) NEC and other PBX people are doing this. If faced with such a situation I would likely look at alternatives, say wireless phone network, older PBX etc.
If I pay $40,000 for a new PBX I expect the company to delivery it, connect it to my existing local phone network, kick her into life and leave. If I later need to redirect PBX ext 2450 from the socket in room 2405 to the socket in room 5609 I should be able to have anyone with a cabling licence, and not a PBX licenced specialist, to be able to change the wires at the board.
I accept that you are stating a corporate rule, I just disagree with the crazy extent to which they are taking it.
by oz_media
You run cable! This really puts your feelings in perspective for me. You are allowed to connect whatever you want on the office side, you can cable your heart out. YOu simply cannot connect to or program the PBX. There are basic end user programs that permit the user to configure extensions and runs but as far as programming the pBX features and bandwidth management, it is proprietary and has been for as long as I can remember, even with basic 8X24 KSU's.
Running and setting up cable and extensions does not interfere with the PBX configuration, they just don't want people connecting line cards, programming PRI etc.
by oz_media
You run cable! This really puts your feelings in perspective for me. You are allowed to connect whatever you want on the office side, you can cable your heart out. YOu simply cannot connect to or program the PBX. There are basic end user programs that permit the user to configure extensions and runs but as far as programming the pBX features and bandwidth management, it is proprietary and has been for as long as I can remember, even with basic 8X24 KSU's.
Running and setting up cable and extensions does not interfere with the PBX configuration, they just don't want people connecting line cards, programming PRI etc.
This discussion is closed to new replies.
Sort by Trending