Question Locked

CD/DVD ROM not working in Windows XP x64 Pro

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I recently built a new computer running WinXP x64 Pro. It has a EVGA nForce 590 SLI AMD2 Mainboard. I am running Windows XP x64 Professional SP2 - it is fully up-to-date via Windows Update.

After installing the OS on a older IDE CD ROM and booting into windows, the IDE CD Rom was no longer recognized. I switched to a USB Combo Drive (COMBO IDE5232CO USB Device from DYNEX Model #: DX-ECOD1). From there I was able to install the nVidia Mainboard drivers. Once the Mainboard drivers were installed, no CD Rom device I attempted to install on the system worked. I have an array of older IDE drives of varying abilities (plain old CDROM, CD-RW, DVD-R), the USB DVD-R mentioned above, and I purchased a new rebranded Toshiba Samsung DVD-RW (under the name Mad Dog Megastore - TSSTcorp CD/DVDW SH-S182D).

After browsing some posts here on Techrepublic. I decided I would try to reinstall the chipset drivers for the motherboard. I removed the drivers for the onboard NVIDIA NForce NEC's, the NVIDIA Network Bus Enumerator, and the NVIDIA nForce System Management Driver. No luck.

I then removed all the drivers for the Primary, Secondary, and Dual Channel PCI IDE Controllers. This seemed to actually change something - although it did not solve my issue. I had, for some reason, 4 driver entries for each type of IDE controller. When I removed all over them and rebooted, only a single entry appeared for each Controller. However, During the course of reinstalling these controllers and reinstalling the Chipset, 3 new redundant entries have appeared under the IDE ATA/ATAPI Controllers - 'NVIDIA nForce 590/570/550 Serial ATA Controller' - these were not present before, and certainly not three of them. (I also am not sure after which step these appeared, because I did not thoroughly check :/ )

Every single CDrom/DVDrom/CDRW/DVDRW I attempt to install shows up with a Yellow Exclamation point and the Device Status of "Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)"

They all also show up as the same driver, Microsoft Driver 5.2.3790.1830 (dated 10/1/2002)

One other thing I would note - there is one Unknown Device running on the system as well - however, I am told that this has something to do with a special feature on the motherboard that only works with Windows Media Center - or some such, and should register as Unknown on other systems.

Any of these CD-roms I have attempted to install have been the only IDE device (other then the USB drive). I only have 1 HD and it is SATA 3.0Gb/s. I do have other IDE HD's but have not attempted to install one to see whether they would work or not.

Any help would be greatly appreciated.

(Just to be thorough, 2 of the other drives I attempt to use but were not listed above are the LG CRD 8480C Internal 48x CD-ROM Drive, and the Hitachi GD-5000 DVD-ROM/DVD-RAM Drive... there were a couple others, but these 2 just happened to be sitting next to my desk at the time I am writing this)

13 replies

by thechas

Does the BIOS properly detect your drives?

If the BIOS does not detect the drives correctly, Windows cannot properly install the driver.

While you did not mention it, did you install any of the drivers that came with the drives themselves? If not, good, as the driver that comes with a CD drive is a legacy DOS mode driver and can mess things up for Windows XP.

While not probable, it is possible that you have a bad motherboard. I would try connecting an IDE hard drive up. If it also does not work, that says that there is a problem with the motherboard. Or at least the IDE driver.

It would not hurt to check with the motherboard manufacture for a BIOS update that corrects IDE device problems.

Chas

by skirsch

Yes, the BIOS does detect all the IDE devices i tried -- they show up in the post and in the cmos interface. And no, I didn't install any drivers that came with any of these drives. Most of the older drives are circa '94 or '99, so I figured any drivers that came with them wouldn't work...if I even still had those disks buried away anyways.

The newest drive, the one I just purchased, came with no driver disk actually. Just some DVD Burner software. In any case, when I went around the web trying to sniff out drivers, all I could really find were firmware flashes -- and, well, I don't have a disk drive in this tower which the older drives required to do a firmware flash, and the new drive's flash program couldn't recognize the drive because window's couldn't

I'll try hooking up a HD and look for a BIOS update and get back to ya.

by skirsch

Bah, I was kinda hoping it wouldn't work, then at least we'd have made some progress.

I hooked up a old HD running Win98 to the same IDE channel i've been trying to get the CDroms to work on. It worked as both a Master and a Slave** and as the Boot Device (although I didn't let it boot all the way through into Win98, just the splash screen).

As for the BIOS, i believe it is up-to-date... however I've now contacted both Phoenix and EVGA to confirm that - and to EVGA I included an extensive report on the problem I'm having.
(BIOS Date: 09/01/06
BIOS Type: Phoenix - Award WorkstationBIOS
BIOS ID: 09/01/2006-NVIDIA-6A61HP32C
OEM Sign-On: (681W1P26))

Thanks for the suggestions and diagnostic attempts Chaz. Any further help or suggestions you or anyone else might be able to give would be, again, greatly appreciated.

** Just to clarify, I tried it as both a Master and Slave more or less just for S's + G's. Actually the real reason is I first loaded it as a slave without checking, with my Win XP x64 HD as the primary boot, and when it worked, I was like 'Wow, if Master/CS is creating this problem, and I never tried slaving the CDroms on a otherwise blank channel - and that fixes it - I'll bang my head into the wall'. Hence me trying it as a Master as well ;)

by langlier

Are the drives on the same cable as anything else? Are they set up as Master or Cable Select? If they are not by themselves in Master try them as such and get back to me.

by langlier

Are the drives on the same cable as anything else? Are they set up as Master or Cable Select? If they are not by themselves in Master try them as such and get back to me.

by thechas

If I am reading things correctly on EVGA's web site, your BIOS is 3 revisions old.

The latest BIOS is version P35 dated 5/20/2007.

No information on what the interim updates changed.

If this were mine, I would be very tempted to flash the BIOS.

Have you tried different IDE cables?

I would also go into BIOS setup and open the Integrated Peripherals section.

Check the settings there. While the EVGA manual does not give a lot of detail, the setting of the HDD Block Mode can impact optical drive operation. And, since most optical drives are not ATA133 devices, you can try setting the IDE mode to lower speeds and see if that helps.

Finally, how do you feel about editing the registry? There is some risk, but that can be mitigated by setting a restore point, and or backing up the registry.

The key of interest here is:
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet\Enum\IDE

Listed under this key should be all of your optical drives, even ones you have removed.

With no optical drives connected, remove all of the sub-keys listing the optical drives.

What your goal here is to remove all optical drives that are not connected to the system so that Windows can start fresh with the next drive you connect.

You might also want to check for a wrong IDE controller as this can give Windows problems too.

Chas

by skirsch

Umm... lets see.

The newest of the CD drives I attempted to use is set to Master. The older two CDroms I tried were both on Cable select.

I have never tried it with two devices on the channel. When I connected the HD I disconnected the CDrom - I tested the HD in both Slave and Master, but not in CS.

However, like I posted above, the HD worked in all forms, as well as the IDE Master & Boot Device.

Again, for S's + G's, I might go ahead and try it with 2 devices, the HD and a CDrom (the newest one) in different master/slave configurations and see if that has any effect on either device working or not working.
I guess while I'm trying things out for the hell of it, I'll use the 2nd IDE channel too, and a different IDE cable.

Does anyone think it might be worth it to try and boot through with a Win98 HD or a WinXP x32 and see if those see the CDroms? The only reason I stopped the Win98 HD at the splash screen was because I knew that - if it even worked at all on this brand spanking new computer (which I kinda doubted, but what do I know) was because it would take an hour to boot it and for it to try and detect and find drivers for everything.

I do however had a laptop HD with a WinXP x32 SP2, and one of those nifty laptop HDs -> desktop IDE cable converters... I'll try all this fun stuff after lunch ;)

by pida_g

Hi, I have the exact same problem with my cd/dvd rom drive. I just built a new computer also with WinXP x64 Pro. My motherboard is MSI K9N Platinum with nForce 570SLI AM2 socket and my DVD rom is samsung DVD-RW SH-S183L.

When I installed windows there was no problems with my dvd rom, until i installed the chipsetdrivers. After that I got the same error message "Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)" with the same driver: Microsoft Driver 5.2.3790.1830 (dated 10/1/2002).

I also only got a burningprogram when i bought the dvd rom, but no driver.

Since I have another motherboard than skirsch I believe the problem isn't about the BIOS or motherboard itself, but rather the chipsetdrivers being bugged in win x64 or something like that.

I'm going to uninstall the chipsetdrivers and see if the dvd rom will work again. I'll edit in the result

If anyone solved the problem i would be happy to know how.

Best regards Peter

by konamtn

I have the same problem with my computer - it runs fine for a bit and then the drives disappear ... I have seen several other posts and have edited the reg file all to no avail - I think MS has stuck us with a "bug" and we have to wait for them to fix it!

by jasonh427

answer from:
http://svenmaes.blogspot.com/2007/06/missing-cddvd-rom-drives-in-windows.html

run regedit

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}

Find the "UpperFilters" and "LowerFilters" (and "UpperFilters.bak" "LowerFilters.bak", if they exist) valuesand delete them.

After that reboot or delete the devices one more time from device manager and voila they were back!

WARNING : some CD / DVD writer programs may have to be reinstalled!!! but that's a small price to pay i find :)

by mikeosip

SPENT ALL DAY TRYING TO FIGURE OUT WHAT HAPPEN TO MY 3 DRIVES. FOTUNATELY SAW YOUR POST AND WITHIN TEN MINUTES MY DRIVES WERE
WORKING AGAIN.YOUR RIGHT ITS A SMALL PRICE TO PAY - THANKYOU!

by skirsch

Hey folks,

Sorry I left this ticket floating for so long, but I got fed up with the issue an gave up... and then about a month or so ago, my computer downloaded some automatic updates, and POOF! Both internal drives and the external drive all installed and came up on my computer -- Go figure. Thanks for all the attempts at help, and I'm glad some other folks got some good feedback from the post!

Happy Holidays!

This discussion is closed to new replies.