Discussion Locked

Cisco 2600 Router for Home Network

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi

i have a broadband 600k internet connection . my boss has given me a Cisco 2600 to "study with" at home .

i would like to

A: configure a home Network
B: make the home pc's able to use the one Broadband Internet connection via the router

i have minimal Cisco experience , but do know that i have an ip address given by my isp , and also have to configure a nat on the router for the home network .

can anyone help me on this ?

11 replies

by jim-h

Request A:
Alright, you mention for part ?A? that you want to configure a home network. Not knowing where you currently are with this just a Basic Hub or Switch connecting your Cisco 2600 and other PCs together is a good start.

Next, go ahead and decide on an ?inside? subnet that will be used just for your home network. Reserved private addresses are preferred but in theory you could really use whatever. The private addresses are 10.x.x.x, 172.16.x.x, or 192.168.x.x. Make sure that you choose the same subnet mask for everyone if they are connected to the LAN created by your hub or switch. Any PC should have a default gateway to your Router IP address.

Finally, make sure that everyone can ping everyone assuming that you are not running local Firewalls.

Request B:
Setting up a Cisco2600 for NAT should not be too difficult. You will just need to decide which configurations method best suite your needs. First, you defining your NAT inside and NAT outside interfaces. Next, you create a Pool of outside address that can/will be used. Finally, add any needed tweaks to your NAT setup using filters, static NAT, etc?

Here is a link to a Cisco?s sample for basic NAT setup.
http://www.cisco.com/warp/customer/556/12.html

Good Luck! Feel free to contact me for any assistance.
-Jim

by jim-h

Well your configuration could easily change base on how you connect to the internet. Static IP, DHCP, PPP, etc...?

I wrote a quick configuration for you below making basic assumptions. Go ahead and give it a try; make sure you put in your Addresses and Interfaces Correctly. Watch the output as you enter commands in case you get an errors message so copy and paste some lines and not all.

Feel free to contact me offline for any further assistance.

-Jim
-----------------------------------------------
conf t
!
!The "!" in a Cisco means this is a comment and the command will be ignored.

!Assuming Ethernet 0 is Home NEtwork
int e0
desc MY-HOME-LAN / INSIDE-NAT / 172.16.23.0/24 Network
ip address 172.16.23.1 255.255.255.0
ip nat inside
no shut
!

!Assuming Ethernet 1 is to Internet Modem
int e1
desc MY-BROADBAND-CONNECTION / OUTSIDE-NAT / IP=10.1.1.1/30 for SAMPLE!
ip address 10.1.1.1 255.255.255.252
ip nat outside
no shut
!

!Well you need a default Gateway to the internet.
!Since I used 10.1.1.1 as a SAMPLE...
!we will assume that 10.1.1.2 is connected to it for the Internet Gateway.
ip route 0.0.0.0 0.0.0.0 10.1.1.2

!Create Acces list permitting local addresses to use NAT:
access-list 1 permit 172.16.23.0 0.0.0.255

!NAT Pool for using your Outside Interface and referencing Access-list 1.
ip nat inside source list 1 interface ethernet1 overload
!
exit
!Write the "running-configuration" to the "start-up configuration"...
!So your changes are applied next reload!
write memory
-----------------------------------------------

by sean arnold

Thanks Jim H

this is my idea . i have a broadband modem which will connect to the router via ethernet rj-45 .
the router then will have a hub connected , again using ethernet connections .

i was planning on using an internal address range of 172.23.X.X and a mask of 255.255.255.0

i do not know how to enter this info onto the router and save it , although i can get in to the enabled section , after this i'm lost .

any ideas of what commands i need to input .

by Former member

How are you going to study with this when you're asking for all the answers?

by Former member

How are you going to study with this when you're asking for all the answers?

This discussion is closed to new replies.