Question Locked

Comcast Cable and Pix 501 Static IP assignment - Newbie

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Our office has a PIX 501 ver 6.3(3)that had a Dynamic IP from Comcast. It changed and our support was lost from the outside. We secured a static IP and I am trying to assign the IP with no success. I assume that when the new static IP is set then the former VPN's will function. If I assign the static IP through the PDM then the office loses Internet connectivity. I am also shutting down the LAN DHCP on the SMB gateway from Comcast when I do this as it hands out a 10.1.10.1 address to the outside interface if I do not.
Here is my pix config...
Building configuration...
: Saved
:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password XXXXXXXXXXXXXXX encrypted
passwd XXXXXXXXXXXXXX encrypted
hostname pixfirewall
domain-name ciscopix.com
clock timezone EST -5
clock summer-time EDT recurring
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list inside_outbound_nat0_acl permit ip any 192.168.1.64 255.255.255.224
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute retry 4
ip address inside 192.168.1.21 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool vpnpool 192.168.1.71-192.168.1.80
pdm location 65.165.202.146 255.255.255.255 outside
pdm location 204.181.35.98 255.255.255.255 outside
pdm location 204.249.224.128 255.255.255.192 outside
pdm location 192.168.1.64 255.255.255.224 outside
pdm location 192.168.142.193 255.255.255.255 outside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 65.165.202.146 255.255.255.255 outside
http 204.181.35.98 255.255.255.255 outside
http 204.249.224.128 255.255.255.192 outside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-pptp
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group PPTP-VPDN-GROUP accept dialin pptp
vpdn group PPTP-VPDN-GROUP ppp authentication mschap
vpdn group PPTP-VPDN-GROUP ppp encryption mppe auto required
vpdn group PPTP-VPDN-GROUP client configuration address local vpnpool
vpdn group PPTP-VPDN-GROUP pptp echo 60
vpdn group PPTP-VPDN-GROUP client authentication local
vpdn username administrator password XXXXXXXX
vpdn username remote1 password XXXXXXXXXX
vpdn username remote2 password XXXXXXXXXX
vpdn enable outside
dhcpd lease 3600
dhcpd ping_timeout 750
terminal width 80
Cryptochecksum:d552196da477323f41a4155ba082416b
: end
[OK]

Can someone help me out with this? I've worked for days to make this work and Comcast tells me they are limited in what they can help a customer with. I am using the PDM within the PIX as I am not CLI familiar. Thanks

5 replies

by technogeek-1995

I didn't read everything, but I know that with Comcast, you need a "Domain Name." The name is HSD1.in.comcast.net that is for Indiana. I don't know if it will work for you. I think (if it doesn't work with above) the .IN. part should be your state. DHCP also needs to be the router configuration. That way it can assign IP addresses automatically. That was the problem on the other post I had...
https://www.techrepublic.com.com/5208-6230-0.html?forumID=101&threadID=267066

Good Luck.....(this is the configuration of my router)

by sdrucker

You said that they gave you a static IP address.
They should have also given you a subnet mask and a gateway.
You still have the line:

ip address outside dhcp setroute retry 4

That needs to be changed to:

"ip address outside 65.25.95.41 255.255.255.192"
and there also needs to be some default gateway lines in there... something like:

ip classless
no ip forward-protocol nd
no ip forward-protocol udp
ip route 0.0.0.0 0.0.0.0 65.25.95.1

Obviously, the 65.25.95.x addresses aren't your REAL addresses, but the ones that Comcast gave you when you switched to the extra $/mo plan that gives you a static IP address.

I hope that this helps.

by dhoag

I should have clarified that this is my initial config from the PIX as I wanted to start from scratch with the "pros". When I set the static IP in the PIX then the whole network loses Internet. I see no where in the PDM to add the suggested lines but will figure that out in the CLI. I am learning lots as I go and appreciate your guidance. I will try your suggestion and post with the result.

by cg it

does your internet work with DHCP enabled on the PIX external interface?

Try your configuration without the ACL enabled and see if that works. A lot of the times, it's the ACL that screws up connectivity since there is an implicit deny statement at the end of all ACLs'

you might want to try the permit any any statement instead of permit any and then 192.168.1.64

Ref: access-list inside_outbound_nat0_acl permit ip any 192.168.1.64 255.255.255.224

This discussion is closed to new replies.