Question Locked

Computer can access internet, but not local network

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I've got a local network at home set up through a Linksys router, with a cable modem on the other end. I've got a laptop, a desktop, and a DVR. Everything can access the internet just fine. The laptop can ping everything, including the desktop. The desktop can ping itself, the router, and remote sites on the internet, but attempts to ping anything on the local network just get "Request timed out." Both computers run XP, but have different workgroups and domains. The desktop runs Windows Firewall, but turning it off didn't help. My main concern is getting the desktop to talk to the DVR, but hopefully the answer lies in why one computer can ping the other but not vice-versa, which is a symptom I could not find in any help files or web searching. Thanks in advance for any help, because I'm stumped.

16 replies

by mr.wiz

Try having all devices in the same workgroup.

by michapman

The desktop is in a workgroup, the laptop is in a domain, and the DVR, as far as I can tell, can be set for neither. I tried to make the desktop not be in a workgroup, but I could not see any way to make that happen. I can't mess with the network setup on the laptop.

by scott_heath

Typically this sort of problem is caused by a firewall. Even if you trun off Windows firewall if you have other security products installed (TrendMico, McAfee) they may have their own firewall. On each system open a command prompt and type IPCONFIG. Try pinging other systems IP Address instead of the computer name. It's also possible that your home router isn't handling internal DNS properly or is trying to send the requests to the external DNS server. What are the DNS settings on each of the PCs set to? If you've set them to internet DNS servers it would explain the ability to ping external addresses and not internal.

by michapman

The only other security product I have running is Symantec Anti-Virus which does not, as far as I can tell, have a firewall.
I have been doing all the pings to IP addresses rather than computer names.
Under TCP/IP Properties, both are set to Obtain DNS server address automatically. Under Network Connection Details, both show the same DNS servers.

by xt john

Do the machines have File and Printer Sharing for Microsoft Networks enabled? If so, you may be able to connect manually by typing the ip address into the run command like this:

\\192.168.0.1

This will usually bring up a dialog box, asking for the admin password of the machine you're attempting to reach. There wil lalso be a checkbox to have teh connection remembered. Once in... you should see the printer/folder shares in an explorer type box.

by scott_heath

On the Desktop PC - Right click on My Network Places and then go to properties and right click on the Local Area Connection and choose repair. See if that helps. Try changing everything to static and changing it back. I've seen the IP stack get messed up before and that seemed to work.

by michapman

Like pinging, I can access the desktop from the laptop, but not the other way around.

by michapman

When I first tried Repair, it wouldn't work because it couldn't get past the renew, even though ipconfig -release and -renew worked just fine. When you said to change everything to static, did you mean under the TCP/IP settings? I tried that and then switched it back to automatic and Repair does work now, but I'm afraid I still can't access the local network.

by scott_heath

...you go to Start, Run, and then type \\laptopipaddress\c$

by michapman

It takes quite a while, then a dialog pops up:

\\laptopipaddress\c$

The network path was not found.

And yes, I did substitue the actual address there. ^^

by scott_heath

Run "netstat -r" on your desktop pc. Take a look at where it thinks it should be routing stuff on your network. I am assuming you are using a class C with a 24 bit mask like 192.168.1.0/24. If you aren't you may want to change that. Or maybe the route table is screwed up. If you want you can post the route table here for us to look at. You can run "route -f" to clear the gateways then repair the connection to restablish them. The only other thing I can think of would be a virus of some sort.

Also, try taking all the DHCP settings assigned to your nic and set them statically and see if it works. I think for us to go much deeper we would need the IP config info from both your PCs and maybe your route table info on both and perhaps a list of running processes. Your laptop may have a firewall on it that you don't know about. It's joined to a domain so I am assuming it's a company laptop.

by michapman

For some reason, it won't let me reply to the last post, but I can reply to the main one.

Active Routes:
Network Destination, Netmask, Gateway, Interface, Metric,
0.0.0.0, 0.0.0.0, 192.168.1.1, 192.168.1.101, 20
127.0.0.0, 255.0.0.0, 127.0.0.1, 127.0.0.1, 1
192.168.1.0, 255.255.255.0, 192.168.1.101, 192.168.1.101, 20
192.168.1.101, 255.255.255.255, 127.0.0.1, 127.0.0.1, 20
192.168.1.255, 255.255.255.255, 192.168.1.101, 192.168.1.101, 20
224.0.0.0, 240.0.0.0, 192.168.1.101, 192.168.1.101, 20
255.255.255.255, 255.255.255.255, 192.168.1.101, 192.168.1.101, 1
Default Gateway: 192.168.1.1
===========================================================================
Persistent Routes:
None

The laptop's route table looks the same, save for an additional line which looks like the last one above, only with an Interface of 3.

While the laptop may have a firewall, the DVR is what I'm really trying to reach, and that should not have one.

Oh, and when you talk about manually setting the DHCP information on the NIC, I assume you're talking about entering the Internet Protocol (TCP/IP) Properties, rather than getting them automatically. I tried that and it didn't make a difference.

by scott_heath

Sorry about being unclear, I did mean to take the settings supplied by DHCP then enter them manually to see if it made a difference.

Your route table looks normal enough. When you "last line" are you referring to the gateway? and is "Interface of 3" referring to the Interfaces as they are listed before the route table or the last octet of an IP address?

I can think of no reason it shouldn't be working at this point. So how did you determine the IP of your DVR? And you are absolutely sure you can ping it from the laptop? Have you tried logging into your router and pinging it from there to see what it does. If your router allows for that sort of thing. Also, have you tried rebooting the router?

by michapman

Boy, do I ever feel silly. Fortunately, it did not magically fix everything or I'd feel even sillier. When I rebooted the router, the IP addresses all got shuffled around. Now the desktop still can't ping the laptop, and the laptop can't ping anything on the local network, but the desktop CAN ping the DVR, so I'll call that a win since that's what I was really after. It does make me wonder if my router is the problem, because I've had suspicions that it's a troublemaker. Thank you very much for all your help.

by scott_heath

Those home routers can do very weird things. I seem to need to reboot mine every few weeks. Take care.

Scott

This discussion is closed to new replies.