Question Locked

Computer not booting or showing video after upgrade

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I upgraded from 2 gb of ram to 4 and now my computer won't boot or show video (We tried putting the old stuff back and it didn't make a difference). It has showed video twice since yesterday but I was unable to do anything, I saw the post screen and it detected the new ram ok. My brother bought a new mobo today so thats brand new now (Asus M2N32-SLI Dlx.)I was hoping the new mobo would fix the problem but it didn't help anything. We've gotten it to post normal a few times at least just the normal beep but no video. I was leaning towards replacing the video card but then I tried it again and the asus AI logo showed up and it posted normally and everything was looking good then it just stopped after detecting the DVD drive. I think I'll take it in to get a diagnostic of the problem if I can't fix it by the weekend.

Specs:
Asus M2N32-SLI Dlx
AMD X2 6000+
Corsair XMS2 DDR2 6400 (4x1GB)
Nvidia GeForce 8800 GTS XXX Edition 320mb

13 replies

by thechas

It sounds like you may be past the hardware problems. However, if you are running Windows XP, 2000, or even Vista, neither likes to boot up after significant hardware changes.

What was the original motherboard? If the chip-set is different, (even if it is from the same manufacture) Windows may lock up and require at least a repair install. If not a full reinstall.

Also, there are known issues with running more than 3GB of RAM on XP or W2K 32 bit versions.

Chas

by boxfiddler Hot topic

and wanted to say thanks for tidbits I didn't know or forgot I knew! :)

by i.hate.bell

so I put in an old cpu (AMD 64 3800) from my dell and tried starting it up for a laugh and guess what; it boots, with video too! anyways I had to press F1 cause of something with the cmos and it loaded fine after that, even right into xp. I went into the kitchen for a second and when I came back out the screen was black and the computer was beeping like crazy. Any ideas on what that means?

by dumphrey

but they all could be wrong...
1)When you put in the "Old" cpu, it was not seated properly, or the heatsink not seated properly, causing over heating.
2)The Video card is shot, but only partialy, hence the intermittent error.
3)The Bios became "corrupt" and should try resetting it.
4)The motherboard is going bad.
5)For some reason both processors you have are bad.
Like I said, lots o guesses.
What I would try.
1)Put back in original processor. Make sure its well seated.
2)Put in only 1 stick of the original ram.
3)reset cmos/bios settings using the mobo jumper.
4)reboot into bios setup and choose "safe" settings.
5)Reboot. If you have no beep codes, its most likely either your video card, motherboard, or processor (processor has to process errors on many mobos to generate error codes, and if mobo dies it cant generate error beeps). But I think you said you purchased a new mobo.
6)Switch out video card.
7)Reboot

See what any of that gets you. Oh btw, the beeping your computer was doing is a form of error code. The beeps are either continuous or in a pattern, and those patterns are unique to each type of bios. You can get info on the beep codes from your computer or mobo vendor.

by i.hate.bell

we double check the seating of all piece in the computer afew times now so hopefully its all seated correctly with the video acting all strange is what gave us the impression that it might be the video card thats dying, As for the motherboard going bad hopefully its not since its brand new and was replaced yesterday there is a chance that both processors are dead, I thinking I should apply thermal paste on. Usually there is no beep code and the one time we managed to get one we we're there to listen :( DOH I'll try doing what you said so figures crossed it atleast helps us figure out whats wrong.

by dumphrey

the hardware well under control. When you boot, do you get the normal single beep on boot up, even with no video? Oh, and does the mobo have built in video?

by i.hate.bell

just went to test the computer again and at the moment we aren't getting past the normal post beep from the mobo telling us that its working however occasionally when we turn it on it posts fine but stays black or posts and works, loads the bios which will complain about the cmos so we hit F1 to revert it back to normal and its launched into windows once, that hasn't happened again and it crashed when my brother was in the kitchen so I'm not sure what the beep code was apparently it went off that time. Sadly no the mobo doesn't have built in video, not surprising since it seems to be top of the line atleast in the stores around here. we have an old graphics card but the problem with testing that is that we have no idea if it still works.

could a lack of thermal paste/processor over heating be the cause of this?

by dumphrey

an overheating processor will shut down, and the bios SHOULD shutdown the computer. If you still have the other processor, but it in a known working mobo, and see if it works, then put it in this computer, use thermal paste (about as much as a thick piece of typing paper on top of the cpu core) and heatsink.

Constant overheating can fry a cpu.

by i.hate.bell

sadly we don't have any thermal paste at the moment and our other computer doesn't have the same motherboard socket I'll go out and buy some, if this is the problem after doing so our computer should boot? that is if we didn't already fry the cpu

by dumphrey

that it will boot, but you do NEED thermal paste between the cpu and heatsink to prevent damage. Do not forget to try a different video card as well. If nothing else "buy" a new one and the return it that same day for any of 1000 reasons (needed agp this is pcx etc). We need to eliminate the other problems it could be.

by i.hate.bell

thanks for all the help the thermal paste on the cpu is old now so it wouldn't surprise me if that was the situation we'll pick another graphics card & thermal paste tomorrow or the day after to test that. just one more question when do you have to change the thermal paste on a cpu? when you change mobos? are there any other times, its one of the few things I'm unsure about.

by dumphrey

anytime I take the heatsink off of the cpu. Unless its only been 30 min since I put new paste on, then I just tidy it up. But once its set up for 24/48 hours with a running computer, its best to replace it aftewr taking off the heatsink.

This discussion is closed to new replies.