Question Locked

Configuring frac T1/Router/Dual Port NIC/SBS 2003 R2 Premium Network

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Greetings,

I'm having a hard time configuring IP and DNS with the following setup:

Frac T1 -> Router -> connection3 -> SBS -> Server Local Area Connection -> Switch -> LAN

Server Config
+ System: Dell PowerEdge 2900
+ OS: SBS 2003 R2 Premium Edition
+ NIC: Dual Embedded Broadcom? NetXtreme II + 5708 Gigabit Ethernet NIC (disabled)
+ Intel? PRO 1000PT Dual Port Server Adapter, Gigabit NIC
+ LOM NICs are TOE Ready)
+ Dell Remote Access Card, 5th Generation for PowerEdge Remote Management

Router
+ Machine: Linksys WRT54GS
+ ISP: XO.net Frac T1
+ WAN IP: Static given by ISP
+ GW: Static given by ISP
+ DNS: Static given by ISP
+ Subnet: 255.255.255.0
+ LAN IP: 192.168.1.1
+ DHCP: Disabled

Connection3 (Port A on the Intel Dual-port)
+ IP: 192.168.1.10
+ Subnet: 255.255.255.0
+ GW: 192.168.1.1
+ DNS: 192.168.16.2

Server Local Area Connection (Port B on the Inter Dual-Port)
+ IP: 192.168.16.2
+ Subnet: 255.255.255.0
+ GW: Blank
+ DNS: 192.168.16.2
+ WINS: 192.168.16.2

Is there anything wrong with this setup? I have no internet connection from the server and I can't even ping router from the server (obvious). When I change the TCP/IP setting fro 'Connection 3', I get

"Warning: Multiple default gateways are intended to provide redundancy to a
single network such as and Intranet or the Internet. They will not function
properly when the gateways are on two separate, disjoint networks (such as
one on your intranet and one on the Internet). Do you want to save this
configuration?"

Also, when I first check DHCP server, pooling was set to, forgot exact range, 192.168.1.x to 192.168.1.xx

Many thanks in advance

7 replies

by bart777

Set the network up in a single subnet.
Disable NIC 2 on the server.
Keep the 192.168.1.x address on the SBS server.
Set DHCP to point the gateway to the router.
Set DHCP to point to the SBS server for DNS.
Setup the DNS forwarders on the SBS server.
Configure the router to forward you external connections to the server, such as you smtp port.

At this point your network is flat and much simpler. You could pull your hair out trying to troubleshoot the other scheme. Most of the customers I've had use SBS in this setup. Since you have a firewall already let it do it's job and the server can do it's job.

Best of luck.

by cg it

When you say fractional T1 line, are you implying that you have 1 global local address? or do you have a pool of them and bandwidth is allocated to each one?

Are you running ISA server 2004? if so, did you install the firewall client program on workstations? If not, install the firewall program on workstations. it's found in the client apps shared folder.

Next. Did you run the connect to the internet wizard from the things to do list?

If not, you need to.

by charles

We have a pool of address from what I know. Wow... does this matter?

And regards to ISA, I just got this system so I'm not even upto setting up ISA yet. I did ran wizard numerous time but no avail. When I run internet wizard, it ask for ISP given DNS address. Which address should I supply?

Thank you so much CG IT.

by charles

Thanks bart777!

But I don't quite understand your instructions.

Set DHCP to point the gateway to the router.
Set DHCP to point to the SBS server for DNS.
Setup the DNS forwarders on the SBS server.
Configure the router to forward you external connections to the server, such as you smtp port.

Would you please explain in little more detail? I'll give it a try when I get to work few hours later. I'll have to work on it overnight =(

by bart777

I just describing a way to flatten your network out.

If you have all of your PCs point to the SBS server for DHCP you can do the configuring in this to get the PCs pointing to the internet and the server at the same time.
Configure your SBS DHCP server settings to use the SBS server as the DNS/WINS server.
Also set the default gateway address to be the router to the internet.
the last thing you need to make sure of is that the SBS server's DNS server service is set to use the ISP's DNS server addresses as the DNS forwarders.

In the router you need to make sure that port 25 is set to forward traffic to your SBS server's Ip address so that the Exchange server will be able to receive mail. Also any other ports you would like to forward can be configured at thsi time, such as 3389 for RDP, or 110 for POP.

Setting things up in this fashion makes you netowrk a single layer, single subnet. This is much simpler to deal with.

Hope this helps Charles.

by cg it

If your using Cisco equipment [router or a PIX] with a fractional T1 and a pool of addresses assigned, you need to know what public address your going to use for http traffic. I assume that the reason you have a pool is so that you can assign different public addresses for different public services and thus assign bandwidth in 64kb chunks. Then you have to configure the Cisco router [or PIX] for many to one NAT for http traffic using the External NIC IP address as the source address. All internet traffic on a SBS dual NIC network goes through the SBS box and out the External NIC. The External NIC needs to be configured with an address, subnet maks, ISP gateway address, and ISP DNS addresses.

If your using SonicWall TZ series, it's a lot less of a problem. you just fill out the wizard form using the routers IP address and your ISP provided DNS addresses to the SBS external NIC [the one that connects to the router]. Your other NIC will be the one that connects to your LAN switch.

This discussion is closed to new replies.