19 replies
by danny.williams Accepted solution
by rob miners Accepted solution
Can the Hard Drive and CD/DVD be seen in the BIOS. If not check the Cabling and Jumper Termination. Hard Drive Master on IDE1, CD/DVD Master on IDE2.
Common BIOS entry Keys
F1
F2
DEL
ESC
F10
A user will know when to press this key when they see a message similar to the below example as the computer is booting. Some older computers may also display a flashing block to indicate when to press the F1 or F2 keys.
Press to enter BIOS setup
Tip: Hold a Key down, this will cause a stuck key error, which may allow you to enter the BIOS setup.
If the PSU is only rated at 200W or 250W replace it with something around 450-550W and dont go cheap as they are inferior and do more harm than good.
Note: A damaged or insufficiently charged internal battery can corrupt CMOS or BIOS settings.
Let us know how you get on.
by abdirisaq8 Accepted solution
by robo_dev Accepted solution
you have to enable the secondary SATA port on the motherboard through bios setup.
Only 2 of the 4 SATA ports are enabled by default on Dell systems
by oh smeg Accepted solution
Did you replace the HDD with the correct size HDD.
IDE Drives have a upper Size Limit beyond which BIOS can not recognize them. If you have replaced the drive with a similar sized one it shouldn't be a problem but if you have replaced a 10 GIG Drive with a 160 GIG Drive this will be a problem and BIOS [b]Will Not[/b] recognize the drive.
You also need to alter the Jumper Setting on the IDE Drive to Master from Cable Select or CS.
If this is a NB you not only need to look at the size of the drive which was removed but the Voltage and Wattage/Amperage of the old drive and compare this to the new one. A HDD with a higher Amperage or Wattage will not work in a system that can not power it.
And if it is a SATA Drive BIOS may not see it and this is perfectly OK as that is how this computer is. If it is a SATA Drive you not only need a Dell Recovery Disc but you need the Dell Recovery Disc for that computer. If you try to use another one it will not have the correct drivers on it and will not install the OS. If the Restore Disc that you have is for a Desktop and you are attempting to use it on a fairly new NB it will not have the SATA Driver to allow the OS to be installed on the SATA Drive.
As for the Computer not booting off the CD Rom you need to go into BIOS set the Date & Time and then set the Optical Drive either CD or DVD to the First Boot Device if there isn't a floppy and the HDD to the Second Boot Device. If you have a Floppy drive the Floppy is the First Boot Device, The Optical Drive is the Second and the HDD is the Third Boot Device. When you have this set exit BIOS Saving your Changes and with the Dell Recovery Disc in the Optical Drive restart the computer and the system will now Boot off the Dell Recovery Disc though you may see a message on the screen to [b]Press Any Key to Boot Off the CD.[/b]
Ideally you should list the model of the Dell so that we can give you an answer for your computer. If you want to ask a question about a piece of Software or Loading the OS you also need to tell us what you are using in the Form of a OS and if it is an Application what it is and what version number it is.
A Dell 2400 can be a Dimension, Power Edge, ATI Video Card, a LCD Monitor, Optiplex and several other things.
If this is a Dell Dimension 2400 you have a IDE drive and you need to use one of a similar size set to Master and then in BIOS on the First Page that Appears you have an Option to see the Drive. If it isn't there the Data Cable the wide flat one [i]"the colored edge should be closest to the power plug"[/i] is in the wrong way or the Power Plug isn't in Properly. Actually both the leads may not be in correctly as they are a tight fit and you need to be Firm but not Rough in fitting them.
If you care to post back with your System Model and the HDD that you have to replace the one in this computer someone here will help you out with a solution.
Col
Col
by danny.williams Accepted solution
by danny.williams Accepted solution
by rob miners Accepted solution
by fatmann Accepted solution
by oh smeg Accepted solution
If the original Drive was 40 GIG and you have bought a 160 GIG Drive the Hardware was never designed to work with something so big. It is like trying to fit a 747 Motor into a Honda Civic. Yes it can be done but there is a lot of ginning around involved and it certainly will not be Plug in and work.
You can try flashing the BIOS to the newest one available and this may increase the size that BIOS can see but it will not reach to the 160 GIG Limit on this M'Board. If you want to use this drive you need a PCI to IDE Adapter Card and fit this to the computer and connect the drive to it instead of the M'Board. Then when you install Windows you'll need to press the [b]F6 Key[/b] when the very first blue screen appears and when prompted insert the IDE Adapter Driver copied to the root of a floppy into the A Drive and press enter. The Windows Installer will then load the IDE Adapter Driver and you will then see the HDD in the Windows Installer.
You can use a Software application like Seagate's Disc Wizard to trick the BIOS into using this drive but this isn't the easiest option and it may prove unreliable latter. Of course fitting a Drive that BIOS can actually see would be the easiest solution here.
Col
by robo_dev Accepted solution
Then our hypothetical Pratt & Whitney JT9D equipped Honda Civic would be unlikely to achieve the rated 56,000 lbs of static thrust.
Similarly, if the power connectors are not properly seated and providing the appropriate voltage and current to the hard drive and CD-ROM, then the combination of an eleven foot long (132.7"), 8,885 pound airplane engine in a 2,000 pound automobile would be just as likely not to operate successfully.
by oh smeg Accepted solution
But as this isn't a new build I'm supposing that the IDE Lead is at least connected the right way on the M'Board if nothing else. I think I mentioned which way the IDE Lead should be plugged into the Drive above earlier but that may have been elsewhere.
Besides I was never into the Wacky Racers and wouldn't consider something that big suitable for a civic particularly when there are some really nice small Military Engines available that would fit the bill quite nicely. :D
But given the chance I would really like to find a different use for a Pegasus Engine. They are just a cure little engine. B-)
Now what did that guy say something along these lines [b]Cars are OK but to really get me interested it's got to have a Afterburner.[/b] Well something like that at least. Beside you don't get anything slipstreaming you as they just don't run in the jet wash. ?:|
Col
by nepenthe0 Accepted solution
I said that after I jettisoned AV software my computer ran like an F-15 on afterburners.
But don't tell Old Mycroft, 'cause he'll have a flippin fit...
Rick/Portland, OR
by oh smeg Accepted solution
It was a guy by the name of Ken Warby who used to drive a World Speed Record Boat.
I did a little bit of work with the boat as the Afterburner wouldn't ignite in the boat but worked perfectly on the Test Stand at the RAF base in Wagga Wagga. :D
Then when the Air-force apprentices destroyed that motor I was cut loose and allowed to return to my real work. So I never did find out why the Afterburner wasn't working but I defiantly have my own ideas I just didn't get a chance to see if I was right though. :(
Col
I have a Need for Speed. :D
by nepenthe0 Accepted solution
Wasn't T.E. Lawrence (Lawrence of Arabia) engaged in similar research when he was working for the English Army? Alas, within a month of his discharge, he crashed his motorcycle to avoid some boys playing in the street, and never regained consciousness.
Rick/Portland, OR
by danny.williams Accepted solution
Ok peoples, I downloaded the bios information from the dell site by the service tag#. The computer wouldn,t recognize that there was anything in the drive (floppy that is).I did set the boot sequence for the floppy to be the first boot-up.I have tried the jumper settings at master and at cable select, no change. I have double checked the IDE cable for correct polarity and seated properly.I have tried to boot w/out battery installed, to reset bios?, no help. Removed battery for 30 minutes and reinstalled, no help.I am missing something/procedure order, or my mother board is at fault? Any other things to try?? I seen chipset file on dell site, but did not have the floppy space to download.Do i need to do that?
Appreciate you all!
Dan Williams
by oh smeg Accepted solution
You also need to download the Flashing Utility copy both of these to the Root of a Floppy and then boot the Computer off a Boot Disc, then when you get the DOS Prompt [b]C: >[/b] change Floppies and type in the Flash Utility Name and press Enter.
You can download a copy of a Boot Floppy from here I suggest the Windows 98 one as it's easy to use.
Have you looked at the Jumper on the HDD? If there is only 1 HDD in this computer it should be set to Master but if the Optical Drive is on the same IDE Lead and set to master neither Drive will appear in BIOS, the same applies if both are set to Slave as well.
If you do not know what a Jumper is there are 2 rows of Pins between the IDE Socket and the Power Socket on the HDD. On the sticker on the HDD there will be a Diagram telling you which is Master, Slave and any other settings that this particular drive may have available.
You also need to look at the Size of the HDD as if it is dramatically different to the one that came out BIOS may not be able to recognize it even with a Upgrade or Flash of the BIOS.
Col
by danny.williams Accepted solution
I need to replace the motherboard on my dell. I am having trouble knowing which motherboard to get. I think its socket is a Mpga478b ??????
The #'s from the uprocessor I.C. is 2.4 Ghz/128/400 SL6VU 54378577
It is a pentium 4.
Which mother board can I use? I do not need anything fancy. Onlu use it for e-mail, pictures, music etc. No gaming or movies.
by oh smeg Accepted solution
And is no longer supported by the new CPU's types. The M'Board that you currently have supports the Older P4 CPU Format and the DDR RAM which has been replaced with 776 Pin CPU's in Single, Dual or Quad Cores with more Internal Cache and DDR 2 or 3 RAM which is considerably faster and cheaper than the existing DDR RAM so you are going to have trouble finding a Current Model M'Board for starters.
The newer M'Boards use a 24 Pin ATX power Connector + either a 4 or 6 Pin Axillary Power Connector so your current Power Supply will need replacing as well and you may have issues with the existing HDD and any Optical Drives as the new ones all tend to be SATA instead of the older IDE drives so the new M'Boards don't have as many IDE Connectors and do have SATA Connectors.
The next thing is that because you have a Dell you only have a Dell Recovery Disc which possibly will be no use to you with a New M'Board as it lacks the necessary drivers to allow you to install the OS. If you are looking at using XP Pro you need to limit the hardware to Single or Dual Core CPU's as XP Pro can not support any more CPU's. That is a design limit built into XP that isn't currently in Vista though currently Vista has a Upper Limit of 4 CPU's or Cores that it can use.
So within those limits you can look at these ASUS M'Boards which show as Current Models though many shops may not have stocks
These are all according to ASUS 845 Intel Chip Set M'Boards which is the same type as you originality had fitted by Dell and will take the existing hardware like CPU and RAM or these 865 Chip Set M'Boards by ASUS
You'll just have to look for one with On Board Video like the one you currently have as this uses the CPU & System Memory to generate Video, or these Gigabyte M'Boards which are newer 865 Chip Set M'Boards
actually just look at the 854 and 864 Chip Set M'Boards listed here
These will fit right in though the supplied Back Plate will most likely need changing with the new M'Board but these are supplied with all new M'Boards so that shouldn't be a problem. These M'Boards will use your existing CPU and RAM if you get one with On Board Video you will not need to buy a Video Card.
The only possible problem here may be the need to change the Power Supply if the M'Board that you end up getting requires a 24 Pin ATX plug and it's probably a good idea to replace the PS with a Brand Name one to get rid of the cheap one that Dell buy and can fail taking the M'Board, CPU, RAM and Drives along with it. All the new PS's that I buy come with a 24 Pin ATX connector that can be used with 20 Pin ATX M'Boards so that shouldn't be an issue. These Days I only use Gigabyte or ASUS M'Boards as they seem to work much better than any of the others but the ones you need to avoid are the Foxcom, ECS, PC Chips and the like. I have seen decent service from MSI and Aus Rock M'Boards but don't personally use them.
Of course if you want to go to either a Dual Core AMD or Intel CPU you'll have to also replace the RAM and CPU to get the newest technology which should be freely available unlike the older 845 & 865 Chip Set M'Boards.
Cheers
Col
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending