Question Locked

Desperate to setup D-Link DI524 wireless router.

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi All,

I may sound like very primitive or asking for a complete support, however I have no choice. I have a D-Link DI524 wireless router which I am trying to set at my home with my TATA Indicom DSL internet. I have tried multiple things for connecting my wireless but this simply does not work. I have tried below ways to access my wireless:

1. Set up the WAN side IP in the D-link router to 192.168.1.5, the subnet mask to 255.255.255.0 and the gateway to 192.168.1.1, then set my DNS servers to 202.54.9.1 and 202.54.1.30.Nothing.
2. Accessed wireless D-Link IP 192.168.0.1 entered Internet uid/ password for PPPoE but nothing. I had to however access the D-Link router with a wire from router to the machine. I just connected to wireless network but the network does not get any connection from the Internet.

Can someone please put in some comments like what else need to be done to achieve this impossible task of setting up the wireless with my TATA Indicom connection. Taking to the support guys at TATA Indicom is a complete waste of time as they not technically sound to install a wireless router (neither am I).

Any and all inputs are welcome.
Thanks in advance for all your time.

Regards,
Utkarsh Gadewar.

16 replies

by cookieorc

First off you cannot set your WAN address to a private address. Your IP address cannot be in any of these ranges:
10.0.0.0 ? 10.255.255.255
172.16.0.0 ? 172.31.255.255
192.168.0.0 ? 192.168.255.255
Can you connect when your computer is directly connected to your modem? It could be how you set up your login to work on your modem. I know there are some wirless routers/modems that allow you to enter in your PPPoE username and password. Does your company offer anything like that?

by utkarshg

Yes I can connect to the Internet after signing in from the ISP's loginid/ password screen.
I am trying to set this router @ home, so nothing from the company.
System that I am using is HP 530 laptop.

by 1bn0

Is it
PPoE (Point to Point over Ethernet)
Static (assigned IP address from the ISP)
DHCP (Dynamic Host Configuration Protocol)automatically assigned by a server from the other end of the link.

If your connection is any of these than just configure the router accordingly and you should not have any issue.

by utkarshg

Yes it is PPoE and I did configure this on the wireless router, but no use.

by 1bn0

Some providers try to tie the DSL modem to the computer. The modem will respond to the computer that is used to set it up and no other unlesss it is reset. This usually applies to cable ISPs' but may be relevent to your situation. Connect to the router from your desktop. Find the Clone MAC settting. Some routers will read the MAC address themselves some you have to enter manually.
start | run | cmd

ipconfig /all

you will see your (wired)mac address listed.
(physical address)e.g. 00-13-72-85-42-EE

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme 57xx Gigabit Cont
roller
Physical Address. . . . . . . . . : 00-13-72-85-42-EE
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : xxx.xxx.xxx.177
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : xxx.xxx.xxx.248
DNS Servers . . . . . . . . . . . : xxx.xxx.xxx.69
xxx.xxx.xxx.108
Primary WINS Server . . . . . . . : xxx.xxx.xxx.69

by ebouza

Setup your WAN side on the DLink router to pick up an IP from your dsl router. Once you set that up reboot your dlink and it should pick up the ip from your dsl router. After that you should be able to get out to the internet. Remember that the LAN ip address does not matter what it is because that is the inside of your network. Hope this helps you. Good luck.

Erick

by utkarshg

Hi Erick,
Thanks for your input.
Can you tell me if it is necessary to set the userid/ password given by the ISP on the D-LInk router PPoE settings by accessing 192.168.0.1.
Also if I am not wrong by you line "Setup your WAN side on the DLink router to pick up an IP from your dsl router." you mean to say that setup the IP on the D-Link router to the same range of the DSL router?. Somehow i think i tried this but it did not work. Did i go wrong in setting up something there like Wrong Default Getway or wrong Preferred DNS ?

Utkarsh

by ebouza

Actually your DSL router should be set automatically to DHCP so your D-Link router should pick up an IP automatically from your dsl router. Answering your first question yes you will need to input your user id and password given to you by your ISP.

Please post again if you still need additional help.

Erick

by utkarshg

Hi Erick,

Thanks for your input first of all.
I think there is something with the ISP's DSL router, does it have to add some settings on the DSL router for D-Link router to pick up IP.

Things are a lot more tricky in India I guess, the same D-Link router worked just like plug and play in the US.

Once i get this i am going to make a Wireless settings for dummy's document on this and post it on the net.

Regards,
UG.

by ebouza

Log into your DSL router and check to make sure it is setup to hand out IP's. If not change the settings in the DSL router and make it a DHCP server, after you do that your DSL router should start handing out IP's. You will then need to reboot your D-Link router and it will pickup the IP that the DSL router is handing out.

I know that the DSL routers normally in the U.S. come from factory with the 192,168.1.1 ip. Get your laptop and connect directly to the DSL router and open up a Internet Explorer window and type in the default ip for the DSL router, once you are logged in go through all the settings and one of them is going to be to have it act as a DHCP server.

If you have any questions please continue to post them and I will try to help with whatever I can.

Good luck,

Erick

by utkarshg

HI Erick,

Thanks for your time again.
OK i found the DHCP setting on my DSL router and i see it saying
1.1 Enable DHCP server
1.2 Start IP address
1.3 End IP address.
This was already configured. Now this has another setting saying:
2.1: Enable DHCP server relay.
Which i used and then connected the wireless router, No results.
When i connect the wire from DSL router to the wireless(the same wire which i join to my laptop without wireless) it says local are network unplugged. Has this something to do here. Also my wireless IP address is configured in the range which is in the 1.1 and 1.2 settings.

I hope i am not trying your patience. Thanks for your time.
Regards,
Utkarsh

by utkarshg

Hi There,

If i find he clone mac setting(which i did not) then what do i do with it :(? I guess i sound a little dumb on this one. However sorry to say but your answer did confuse me a bit.
My DSL router is Broadcom TAD100
Regards,
Utkarsh

by 1bn0

Every ethernet device has a "UNIQUE" MAC Address. They are sort of like street addresses for the network interface. The IP address can change everytime the machine connects to the network but the MAC address stays the same (it can be changed,but was not originally intended to be so). This is also the basis for WOL Wake On Lan utilities that let you turn on a computer as long as it is physically connected to the network and the NIC has power.

The config on the DSL router is set to only allow 2 devices to obtain an IP address from your provider. I don't think you can actually define a single IP address range,2 is the minimum.

This makes me think they are definitely limiting what you connect to the line. Cable providers in North America do the same thing. They still want to run the ISP side like Cable TV side where they charge for every device conected to the network.

The DSL modem/router responds to the first Computer connected to it. And only the first. It identifies this machine by storing the MAC address of the NIC in the computer.

Cloning the MAC address in the router tells the router to program its WAN interface to use the MAC address of the computer that was previously cabled to the DSL modem/router.

The DSL modem can't tell the difference and so lets the customers router make the connection.

by cg it

In addition:
I haven't read all responses but typically today, cable and dsl ISPs provide a modem/router combination box to subscribers. This was done to combat consumers having unprotected computers on the internet which were then compromised and used in bot networks for spam.

So, if the modem the questioner is using is one of these combination modem/router boxes then adding in another wireless router into the mix creates 2 networks.

If so, then the wireless router connected to the modem/router combo box WAN port must be on the modem/router's box LAN with a statically assigned address. The default gateway is the modem/router box LAN address and DNS is the ISP DNS servers.

on the wireless router's LAN side, have to choose a different subnet than the modem/router's LAN subnet for the routing function to work. example the modem/router LAN address is 192.168.1.1 then the wireless router's WAN interface would be on that subnet and the wireless routers LAN address would be on a different subnet like 192.168.2.1 .

by ebouza

Utkarsh,

Can you please supply me with your personal email. I would like to send you screen shots.

Erick

Sorry for the delay.

This discussion is closed to new replies.