Question Locked

DHCP & Default Gateway config FAILED... (no internet, WinXP)

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Greetings,

DHCP & Default Gateway config FAILED... (no internet, WinXP) is the problem.

Everything was working fine, and has been for better than a year, then the internet just stopped.

I used my "WinPing MFC Application" ("InstantHelp.exe") to generate this report:

"
Probing Network Adapters... passed.
1 adapters are found.

Probing connected network adapters... passed.
At lease one Adpater is connected - OK!

Probing DHCP configurations... failed.

Probing local IP statck... passed.
Local IP stack intact!

Probing the gateway configuration... failed.

Found: Default Gateway is not configured.

If static IP is configured, please configure default gateway.
If Dynamic IP is configured, restart the device.
Otherwise restart the local router/DSL/Cable modem.
Probing SMTP Server... failed.
Found: SMTP server is down.

Probing POP Server... failed.
Found: POP server is down.

Probing POP Server... failed.
Found: POP server is down.
"

I have tried resetting everything to no effect.

Any help would be greatly appreciated.

Thanks,
Robert Stretton
rbse@yahoo.com
.

13 replies

by cg it

telling us what all this info refers to.

Does [no internet WinXP] mean that this refers to your desktop?

or is the information from your consumer level router or DSL modem/router?

by rbse

I have WinXP as my OS on my desktop.
My internet on my dektop failed.
I have a troubleshooting program for broadband access called "InstantHelp.exe" that I used to generate the above report, in quotes.

I need to know how to "PASS" the "FAILED" items.

I use a Cable Modem / Wi-Fi Router / Wi-Fi Ethernet Bridge to the remote computer, that has the Internet Access problem.

Does that help?
.

by cg it

ok need some more clarification. Is the setup cable modem >>> Wi-Fi router>>> desktop? and do you use wireless or wired?

by grey hat geek

From what I can decipher from your post, you seem to be having router/cable modem problems. Your computer is not going to get a DHCP address if it cannot even find the default gateway. Are you on a cable modem, or DSL? Whichever it is, I would suggest that you check your modem or your router (if you are using one for your network. Do you have a router that is acting as the DHCP server, or is your cable modem set as the DHCP server? Try resetting either/or.

by rbse

Not sure where to set the DHCP server?

The main computer works fine on the cable modem / wi-fi router.

It's the remote wi-fi computer that has failed the connection.

Thanks for all your help.

by nepenthe0

If you have configured the router correctly, as previously discussed, the wireless adapter should be receiving a Wi-Fi signal and searching DHCP for a temporary assigned address.

1) Be sure the router is configured to obtain addresses [i]automatically[/i].

2) Disable encryption.

3) Be sure the 'SSID' is being broadcast.

4) If your adapter is 802.11g, set the router to broadcast in [b]G[/b] mode.

5) Be sure no MAC address filter is enabled.

6) Look for 2.4GHz interference (cordless telephone base station).

7) Look for RF interference (motors, fans, etc.)

8) Avoid metal shielding between youself and the router.

9) If you have a vertical router antenna booster, use it.

10) Disconnect the Ethernet cable from the modem to the router. Boot the router, then reconnect the cable.

11) Sometimes you have to boot both cable modem [b]and[/b] the router.

12) Right click the wireless adapter icon in the system tray and click [i]repair[/i].

Any luck?

Rick/Portland, OR

by rbse

Cable Modem to Wi-Fi Router.
Main Computer is hardwired to port -1-.
Second Computer is Wi-Fi to the Router through an ethernet bridge.
The second computer has no more access.

Does that help further?

by grey hat geek

Why are you going through an ethernet bridge?

It should be this

Internet----->Cable Modem----->connection from cable modem to wireless router

Plug your desktop into port 1 on the wireless router, then you need to go into the router and set it up for wireless access for your laptop. The wireless router is more than likely acting as your DHCP server (giving out ip addresses to your network). You do not need it in bridged mode. What wireless router do you have?

by cg it

the wireless router ought to have come with instructions. Best to read them. If you don't have em, the mfg probably has it available on their web site. I'd get em and follow them.

by boxfiddler Hot topic

They need to be unplugged periodically or they stop working. Some sort of static buildup in the end that plugs into the receptacle.

If you haven't unplugged it for awhile, unplug it for a few minutes, then plug it back in and try everything again.

by rbse

Thank you for your simple yet effective suggestion, it worked this time.

Thanks to all for your help on this.

by rbse

Thanks Rick,

This is a great checklist to troubleshoot an internet connection.

Problem solved.

If this doesn't help you, nothing will...

This discussion is closed to new replies.